TRENDnet TEW-WLC100 User manual
TEW-WLC100
Quick Installation Guide
Table of Content
1 English
1. Before You Start
2. Hardware Installation and Configuration
3. Connect your wireless access points
1
1. Before You Start
Optional Equipment
ŸEIA standard 19” rack
You can download the access point firmware from http://www.trendnet.com/support which
include instructions on how to upgrade the firmware.
Access Point Compatibility
Access Point Model Description Firmware Version
TEW-755AP N300 PoE Access Point 1.02 or above
TEW-821DAP AC1200 Dual Band PoE Access Point 1.04 or above
Before you proceed, please ensure you are using one of the access point models in the list and
the firmware version of your access points has been upgraded accordingly to the versions
indicated in the list below. Please reset all access points to the factory default configuration.
Also, make sure your network is using a DHCP server to distribute IP addresses to the access
points. By default, TRENDnet access point models listed below will obtain an IP address
automatically through DHCP or otherwise default back to 192.168.10.100 / 255.255.255.0 if a
DHCP server is not available on your network. Each access point must be assigned a unique IP
address on the same network.
Package Contents
ŸTEW-WLC100
ŸQuick Installation Guide
ŸCD-ROM (User's Guide)
ŸPower adapter (12V DC, 1A)
ŸRack mount kit
Minimum Requirements
ŸComputer with an Ethernet port and web browser
ŸNetwork cable
ŸWireless Access point(s) (TEW-755AP, TEW-821DAP)
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
2
2. Hardware Installation and Configuration
3. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
4. Open your web browser, type the IP address of the switch in the address bar, and then press
Enter. The default IP address is 192.168.10.200.
1
Power
2
3
6. Click Advanced, click Setup, then click on LAN Settings.
7. Configure the wireless controller IP address settings to match the requirements of your
network and click Apply.
5. Enter the User name and Password, and then click Login. By default:
User Name: admin
Password: admin
Note: User Name and Password are case sensitive.
Login
Note: The Default Gateway and DNS IP settings must be assigned to ensure the wireless
controller is able to check for available online firmware upgrades.
Advanced
LAN Settings
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
4
8. Using an Ethernet cable, connect one of the five Gigabit Ethernet ports located on the back of
the wireless controller to your network (e.g. router, switch, etc.)
9. Access the wireless controller management page using the newly assigned IP address.
Note: You may need to revert to your computer's original IP address settings before you can
access the wireless controller with the new IP address settings.
TEW-WLC100
Network
3. Connect your wireless access points
5
Important Note: Please make sure your access points have met the requirements in Section 1
Access Point Compatibility.
1. Using an Ethernet cable, connect each wireless access point to the wireless controller or
your network.
Note: If powering the access points using their power adapters, you can connect the access
points directly to your network or the wireless controller. If powering the access point using
power over Ethernet (PoE), you can connect your access points to your network or to the
wireless controller using a separate PoE injector or PoE switch (not included).
Network Network Network
PoE Injector
OR OR
Acess Point PoE Switch
Acess Point Acess Point
Power
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
6
3. After your access points have been found, they will automatically appear in the Device List.
2. After the access points are connected to your network and powered on, click on Basic, click
AP Management, and Device List in the wireless controller management page. Then click on
Discover to search for available wireless access points.
7
5. You can modify the access point basic settings such as SSID and encryption key on each band.
4. To configure access point settings, under the Select column, check one or multiple access
points you would like to configure and click on Device Settings to configure access points.
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
8
6. After modifying the settings, scroll down to the Password field, enter the access points
management password (default access point password: admin) and click OK to apply the
settings to the access points.
Note: If you are using a combination of single band (2.4G) and dual band access points (2.4G &
5G), the 5G settings will only be applied to dual band access points.
Other manuals for TEW-WLC100
3
Table of contents
Other TRENDnet Wireless Access Point manuals
TRENDnet
TRENDnet TEW-412APBO User manual
TRENDnet
TRENDnet TEW-630APB - Wireless Access Point User manual
TRENDnet
TRENDnet 14dBi User manual
TRENDnet
TRENDnet TEW-735AP User manual
TRENDnet
TRENDnet TEW-650AP User manual
TRENDnet
TRENDnet TEW-637AP - 300Mbps Wireless Easy-N-Upgrader User manual
TRENDnet
TRENDnet TEW-410APB User manual
TRENDnet
TRENDnet TEW-753DAP User manual
TRENDnet
TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... User manual
TRENDnet
TRENDnet TEW-210APB User manual
TRENDnet
TRENDnet TEW-750DAP User manual
TRENDnet
TRENDnet TEW-638APB User manual
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point User manual
TRENDnet
TRENDnet TEW-411BRPplus User manual
TRENDnet
TRENDnet TEW-670APB User manual
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point User manual
TRENDnet
TRENDnet TEW-740APBO2K User manual
TRENDnet
TRENDnet TPL-210AP User manual
TRENDnet
TRENDnet TEW-430APB - Wireless Access Point User manual
TRENDnet
TRENDnet TEW-821DAP User manual
