TRENDnet TEW-410APB User manual

User’s Guide

TEW-410APB

Wireless 802.11g AP

User’s Manual

Version 1.4

User’s Guide

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical,

photocopying, recording, or otherwise without the prior writing of the publisher.

July. 2003

User’s Guide

Contents

1. Introduction.............................................................................................................. 3

2. Safety Notification ................................................................................................... 4

3. Hardware Installation .............................................................................................. 5

4 Web Management Settings ...................................................................................... 6

4.1. Primary Setup ………………………………………………………………………………………………7

4.2. System…..………………………………………………………………………………………………….11

4.3. Operating Mode……………………………………………………………………………………………12

4.4. Status……………………………………………………………………………………………………….14

4.5 Traffic Log…………………………………………………………………………………………………..15

4.6 AccessControl ……………………………………………………………………………………………..16

4.7 Advanced Wireless………………………………………………………………………………………..17

4.8. SNMP………………………………………………………………………………………………………19

4.9. Upgrade Firmware………………………………………………………………………………………..20

5. Troubleshooting .................................................................................................... 22

User’s Guide

1. Introduction

Thank you for purchasing your AP Wireless 802.11g AP.

This user guide will assist you with the installation procedure.

The package you have received should contain the following items:

 AP Wireless 802.11g AP

 User Guide

 Power Supply / Cord

 Ethernet Cable

Note: if anything is missing, please contact your vendor

User’s Guide

2. Safety Notification

Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please

keep the unit away from water and other damaging elements. Please read the user manual thoroughly

before you install the device. The device should only be repaired by authorized and qualified

personnel.

 Please do not try to open or repair the device yourself.

 Do not place the device in a damp or humid location, i.e. a bathroom.

 The device should be placed in a sheltered and non-slip location within a temperature range of

+5 to +40 Celsius degree.

 Please do not expose the device to direct sunlight or other heat sources. The housing and

electronic components may be damaged by direct sunlight or heat sources.

User’s Guide

3. Hardware Installation

Front Panel

The front panel provides LED’s for device status. Refer to the following table for the meaning of each

feature.

LED STATUS Description

Off No power

Green On

1. Power on 2. Reset to default 3. Firmware upgrade (first 1

minute)

PWR/STAT

Green

Blink 1. System up 2. Power on 3. Firmware upgrade

Off no Ethernet link detected

Green On

10/100Mbps Fast Ethernet link detected. No activity.

Link

Green

Blink Indicates data traffic on the 10/100 Mbps LAN

Active Green

Blink

Indicates the device is linking or active data throug

h wireless

links

Rear Panel

The rear panel features 1 LAN ports and Reset button. Refer to the following table for the meaning of

each feature.

Power (DC 5v)

Used to connect to the power outlet. Only use the power

adapter provided with the device. Use

of an unauthorized

power adapter may cause damage to your device and

violate your warranty.

Reset

Press the Reset Button for approximately ten seconds, all

configurations will set to factory default settings.

LAN The RJ-45 Ethernet ports used to connect

your PC, hub,

switch or Ethernet network.

AP Default Settings

The default settings are shown following.

User admin

Password admin

AP IP Address 192.168.1.250

AP Subnet Mask 255.255.255.0

RF ESSID ap11g

11g RF Channel 6

Mode 11b+g

Encryption Disabled

User’s Guide

Web Management Settings

START UP & LOGIN

In order to configure the Wireless 11g AP, you must use your web browser and manually input

http://192.168.1.250 into the Address box and press Enter. The Main Page will appear.

To start configure the Wireless 11g AP, you must login as “admin” in the User Name box. And input

password “admin” on the password section.

Once you have logged-in as administrator, it is a good idea to change the administrator password to

ensure a secure protection to the Wireless 11g AP. The Security Settings section described later in

this manual describes how to change the password.

Once you have input the correct password and logged-in, the screen will change to the Setup page

screen.

TURN ON POWER SUPPLY

Quick power cycle can caused system corruption. When power on, be careful not to shut down in

about 5 seconds, because data is writing to the flash.

User’s Guide

4.1. Primary Setup

Primary Setup

This screen contains all of the AP's basic setup functions.

Most users will be able to configure the AP and get it working properly using the settings on this

screen.

LAN IP Address and Subnet Mask:

This is the AP's IP Address and Subnet Mask as seen on the

internal LAN. The default value is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask.

MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER

To change the configuration, use Internet Explorer (IE) or Netscape Communicator to

connect the

WEB management 192.168.1.250.

User’s Guide

Wireless:

This section provide the Wireless Network settings for your WLAN

Wireless Settings

SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must not exceed 32

characters, which may be any keyboard character. You shall have selected the same SSID for all the

APs that will be communicating with mobile wireless stations.

Channel: Select the appropriate channel from the list provided to correspond with your network

settings. You shall assign a different channel for each AP to avoid signal interference.

Security: There are 3 types of security to be selected. To secure your Wireless Networks, it’s strongly

recommended to enable this feature.

-WEP

Make sure that all wireless devices on your network are using the same encryption level and

key. WEP keys must consist of the letters "A" through "F" and the numbers "0" through "9."

User’s Guide

-WPA-Preshared key

There are two encryption options for WPA Pre-Shared Key, TKIP and AES. TKIP stands for

Temporal Key Integrity Protocol. TKIP utilizes a stronger encryption method and incorporates

Message Integrity Code (MIC) to provide protection against hackers. AES stands for Advanced

Encryption System, which utilizes a symmetric 128-Bit block data encryption.

To use WPA Pre-Shared Key, enter a password in the WPA Shared Key field between 8 and 63

characters long. You may also enter a Group Key Renewal Interval time between 0 and 99,999

seconds.

WPA

Algorithms

Please choose your algorithms method. You can select

between TKIP or AES.

WPA Shared

Key

Please input the Pre-Shared Key. The key should be 8

characters or 63 characters in alphanumeric.

Group Key

Renewal

Please input the period of renewal time. The default selection

is 300 seconds.

Important Notice

In order to make right use of WPA, please ensure that your current Wireless Adapter’

s driver, and

Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen),

though the Operating System must also support 802.1x protocol. For Microsoft’

s OS family, only

Windows XP has incorporated this by default. The rest of the OS must installed 3er party’

s client

software such as Funk ODySSey.

Other manuals for TEW-410APB

Table of contents

Other TRENDnet Wireless Access Point manuals

TRENDnet

TRENDnet TEW-730APO User manual

TRENDnet

TRENDnet TEW-821DAP User manual

TRENDnet

TRENDnet TEW-738APBO User manual

TRENDnet

TRENDnet TEW-750DAP User manual

TRENDnet

TRENDnet TEW-820AP User manual

TRENDnet

TRENDnet TPL-410AP User manual

TRENDnet

TRENDnet TEW-670AP User manual

TRENDnet

TRENDnet TEW-AP100 User manual

TRENDnet

TRENDnet TEW-636APB User manual

TRENDnet

TRENDnet TEW-815DAP User manual

TRENDnet

TRENDnet TEW-753DAP User manual

TRENDnet

TRENDnet TEW-715APO User manual

TRENDnet

TRENDnet TEW-753DAP User manual

TRENDnet

TRENDnet TEW-310APB Owner's manual

TRENDnet

TRENDnet TEW-650AP User manual

TRENDnet

TRENDnet TEW-412APBO User manual

TRENDnet

TRENDnet TEW-676APBO User manual

TRENDnet

TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... User manual

TRENDnet

TRENDnet TEW-638PAP User manual

TRENDnet

TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... User manual

TRENDnet

TRENDnet TEW-653AP User manual

TRENDnet

TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... User manual

TRENDnet

TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M User manual

TRENDnet

TRENDnet TEW-840APBO User manual

Popular Wireless Access Point manuals by other brands

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Quick installation guide

Ubiquiti

Ubiquiti NanoStation NSM2 quick start guide

Cisco

Cisco Aironet 1550 Series Getting started guide

Aruba

Aruba IAP-335 user guide

Advantek Networks

Advantek Networks AWN-AP-54MR user manual

IP-COM

IP-COM AP355 user guide

Buffalo

Buffalo AirStation WLA-L11G user manual

EnGenius

EnGenius EnStationACv2 user manual

D-Link

D-Link DAP-3662 Quick installation guide

xG Technology

xG Technology xMax CN1300 installation guide

Widelink

Widelink ezWave WAP-1100 Series user guide

Edimax

Edimax CAP1200 user manual

Ubiquiti

Ubiquiti LBE-5AC-Gen2 quick start guide

Aruba

Aruba AP-203R installation guide

LuXout Shades

LuXout Shades LUXSHADE MOTION manual

CreatComm

CreatComm TB5F user manual

SineDigital

SineDigital MW-1500AP(H) installation guide

TP-Link

TP-Link AP9650 V1 Quick installation guide