TRENDnet TV-IP400 User manual
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TV-IP400
TV-IP400W
Version 09.08.05
Quick Installation Guide
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
5
7
1. Prepare for Installation ......................................................................
2. Install Hardware ................................................................................
3. Configure the Internet Camera ..........................................................
4. Using the Internet Camera Wirelessly (TV-IP400W only) .................
Thank you for purchasing the TV-IP400/TV-IP400W. This Internet Camera will
allow you to view live images from internal and external networks.
This guide will help you set up and configure your Internet Camera. Following
the installation instructions should be quick and easy. If you run into problems,
please refer to the Troubleshooting section or the more detailed installation
procedures on the CD User's Guide. If you need further technical support,
please visit www.trendnet.com or call our technical support department by
phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
System Requirement
1. 10/100Mbps Ethernet
2. CD-ROM Drive
3. CPU: Intel Pentium III 450MHz or above
4. Memory: 128MB or above
5. Web Browser: Microsoft Internet Explorer 5.0 or above, Netscape
Navigator 6.0 or above
6. VGA Resolution: 800 x 600 or above
TV-IP400/TV-IP400W
Utility CD-ROM
Quick Installation Guide AC Power Adapter
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TV-IP400
TV-IP400W
Version 09.08.05
Quick Installation Guide
2
2. Install Hardware
1. Place the camera on a flat, level surface.
2. Connect the RJ-45 network cable to the Internet Camera then connect the
other end of the network cable to a switch or hub.
3. Connect the power adapter to the Internet Camera. Make sure use the
power adapter supplied with the Internet Camera.
English
TV-IP400W
Note: Using a different power adapter may damage the unit.
3
2
TV-IP400
3
2
3English
1. Open Internet Browser Window and enter <http://192.168.0.20> (camera's
default IP address)
2. Click on System Administration to access the configuration page.
3. Configure the Internet Camera
Note: The PC's IP (Example 192.168.0.50) address must correspond
with the Internet Camera's IP address (Default IP: 192.168.0.20) in the
same segment for the two devices to communicate.
4English
3. Click Configuration and click Network. Enter an IP address, Subnet mask,
and Default gateway that corresponds with your existing network. Then click
the Save button to keep the changes
Note: If you need to access the configuration remotely, it is
recommended to enter a static IP address and the Internet DNS IP
address.
5English
4. Using the Internet Camera
Wirelessly (TV-IP400W only)
1. Click Configuration and click Wireless.
2. From the pull-down menu, select the SSID that matches your wireless
access point and set Connection Mode to Infrastructure.
6English
3. Scroll down to the bottom of the page and Click Save.
4. Disconnect the CAT5 cable and the power adapter connector from the
TV-IP400W.
5. Reconnect the power adapter connector to the TV-IP400W. Allow 5-10
seconds for the TV-IP400W and the wireless Access Point to communicate
wirelessly. Then type the IP Address that you assigned to the TV-IP400W in
your web browser for verification.
7
Q1.
A1.
Q2.
A2.
Q3.
A3.
The image is blurry, how do I fix this?
You can adjust the Internet Camera's focus by rotating the lens.
How do I view the Internet Camera's live images within my Local
Network?
Open a web browser (Internet Explorer or Netscape), type your
Wireless Internet Camera's IP address (i.e.: 192.168.0.20) in the Address
bar, and then hit the Enter key. The Welcome page of the Internet Camera
will appear.
When I enter the IP address of the camera, the image does not load,
why?
Please make sure all the Active X features are enabled for your
Internet Explorer.
1. Go to Tool (on the Tool bar) g Internet options g Security
Troubleshooting
8
2. Click on Custom Level and make sure all ActiveX controls are set to
"Enable" and click OK.
3. Once you save the settings, the browser will load again and the image
should appear.
Other manuals for TV-IP400
6
This manual suits for next models
1
Other TRENDnet Security Camera manuals
TRENDnet
TRENDnet TV-IP400 User manual
TRENDnet
TRENDnet TV-IP311PI User manual
TRENDnet
TRENDnet TV-H400 User manual
TRENDnet
TRENDnet TV-IP100-N User manual
TRENDnet
TRENDnet TV-IP400W - Wireless Advanced Pan User manual
TRENDnet
TRENDnet TV-IP343PI User manual
TRENDnet
TRENDnet TV-IP410WN User manual
TRENDnet
TRENDnet TV-IP450P User manual
TRENDnet
TRENDnet TV-IP121W User manual
TRENDnet
TRENDnet TV-IP501W User manual
TRENDnet
TRENDnet TV-IP851WC User manual
TRENDnet
TRENDnet TV-IP262P User manual
TRENDnet
TRENDnet TV-IP100W User manual
TRENDnet
TRENDnet TV-IP252P - SecurView PoE Dome Internet Camera... User manual
TRENDnet
TRENDnet TV-IP312PI User manual
TRENDnet
TRENDnet TV-IP323PI User manual
TRENDnet
TRENDnet TV-IP321PI User manual
TRENDnet
TRENDnet TV-IP1328PI User manual
TRENDnet
TRENDnet TV-IP400 User manual
TRENDnet
TRENDnet TV-IP651W User manual
