Texas Instruments SMALL-AMP-DIP User manual

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

User's Guide

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

This user’s guide contains support documentation for the SMALL-AMP-DIP evaluation module (EVM).

Included is a step-by-step guide on setting up and configuring the EVM, bill of materials (BOM), and

printed circuit board (PCB) layout.

Contents

1 Introduction ................................................................................................................... 3

2 Hardware Setup.............................................................................................................. 4

3 EVM Description and PCB Layout......................................................................................... 7

4 Bill of Materials and References ......................................................................................... 10

List of Figures

1 Location of packages on EVM............................................................................................. 4

2 Detach desired PCB......................................................................................................... 5

3 Detached PCB with soldered IC........................................................................................... 5

www.ti.com

2SBOU215–January 2019

Submit Documentation Feedback

SMALL-AMP-DIP Evaluation Module (EVM)

4 Terminal strip (TS-132-G-AA) broken into 4 position length........................................................... 5

5 Terminal strip (TS-132-G-AA) inserted into spare DIP socket......................................................... 6

6 Fully assembled PCB ....................................................................................................... 6

7 DPW package top layer (left) and bottom layer (right) PCB layout ................................................... 7

8 DSG package top layer (left) and bottom layer (right) PCB layout.................................................... 7

9 DCN and DDF packages top layer (left) and bottom layer (right) PCB layout....................................... 7

10 RUG package top layer (left) and bottom layer (right) PCB layout.................................................... 8

11 RUC package top layer (left) and bottom layer (right) PCB layout.................................................... 8

12 RGY package top layer (left) and bottom layer (right) PCB layout.................................................... 9

13 RTE package top layer (left) and bottom layer (right) PCB layout .................................................... 9

List of Tables

1 Package type mapped to EVM............................................................................................. 4

Trademarks

All trademarks are the property of their respective owners.

www.ti.com

Introduction

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

1 Introduction

The SMALL-AMP-DIP-EVM is designed to facilitate evaluation of op amps offered in small packages. This

EVM gives users an easy tool to test the following op amp packages: DPW, DCN, DDF, DSG, RUG, RUC,

RGY, and RTE. This EVM routes each pin of the device to a header pin and can be used as a basic

building block for circuit design and device testing purposes.

1.1 List of Packages

The SMALL-AMP-DIP-EVM contains the following packages:

• DPW-5

• DCN-8

• DDF-8

• DSG-8

• RUG-10

• RUC-14

• RGY-14

• RTE-16

Hardware Setup

www.ti.com

4SBOU215–January 2019

Submit Documentation Feedback

SMALL-AMP-DIP Evaluation Module (EVM)

2 Hardware Setup

The SMALL-AMP-DIP-EVM setup requires identifying and breaking out the desired PCB from the EVM

and then soldering the IC and terminal strips onto the EVM. This section presents the details of these

procedures.

2.1 EVM Package Locations

Figure 1 and Table 1 map the location of each package on the EVM. Figure 1 labels each package

drawing with a letter ranging from A to G. Table 1 matches the package drawing to a letter in Figure 1.

Figure 1. Location of packages on EVM

Table 1. Package type mapped to EVM

Package Name Letter in Figure 1

DPW-5 A

DCN-8 B

DDF-8 B

DSG-8 C

RUG-10 D

RUC-14 E

RGY-14 F

RTE-16 G

www.ti.com

Hardware Setup

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

2.2 EVM Assembly Instructions

This section provides step-by-step instructions on how to assemble the EVM.

1. Choose the desired package. See Section 2.1 for the location of each package type.

2. Gently flex the PCB panel at the score lines to separate the desired package from the EVM.

Figure 2. Detach desired PCB

3. Solder the device onto the separated PCB.

Figure 3. Detached PCB with soldered IC

4. Use long-nose pliers to snap terminal header strips into the desired position lengths.

• For the DPW, DCN, DDF and DSG packages, the terminal strips need to be snapped into 4

position lengths, as shown in Figure 4.

• For the RUG package, use 5 position lengths.

• For the RUC and RGY packages, use 7 position lengths.

• And for the RTE package, use 8 position lengths.

Figure 4. Terminal strip (TS-132-G-AA) broken into 4 position length

Hardware Setup

www.ti.com

6SBOU215–January 2019

Submit Documentation Feedback

SMALL-AMP-DIP Evaluation Module (EVM)

5. Insert the header strips into a spare DIP socket or breadboard as shown in Figure 5.

Figure 5. Terminal strip (TS-132-G-AA) inserted into spare DIP socket

6. Position the separated PCB with the soldered IC over the terminal strips and solder each pin in

place. Carefully remove the PCB from the DIP socket. Figure 6 displays a fully assembled PCB.

Figure 6. Fully assembled PCB

www.ti.com

EVM Description and PCB Layout

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

3 EVM Description and PCB Layout

This section shows the PCB layout of each circuit configuration provided on the EVM.

3.1 DPW Package

Figure 7 displays the PCB layout of the top (left) and bottom layers (right) for the DPW package.

Figure 7. DPW package top layer (left) and bottom layer (right) PCB layout

The X2SON (DPW) package has the following dimensions: 0.48-mm pitch, 0.37-mm maximum height, 0.8-

mm length, and 0.8-mm width.

3.2 DSG Package

Figure 8 displays the PCB layout of the top (left) and bottom layers (right) for the DSG package.

Figure 8. DSG package top layer (left) and bottom layer (right) PCB layout

The WSON (DSG) package has the following dimensions: 0.5-mm pin pitch, 0.75-mm maximum height,

2.0-mm length, and 2.0-mm width.

3.3 DCN and DDF Packages

Figure 9 displays the PCB layout of the top (left) and bottom layers (right) for the DCN and DDF

packages.

Figure 9. DCN and DDF packages top layer (left) and bottom layer (right) PCB layout

The SOT-23 (DCN and DDF) package has the following dimensions: 0.65-mm pin pitch, 1.1-mm maximum

height, 2.9-mm length, and 1.63-mm width.

EVM Description and PCB Layout

www.ti.com

8SBOU215–January 2019

Submit Documentation Feedback

SMALL-AMP-DIP Evaluation Module (EVM)

3.4 RUG Package

Figure 10 displays the PCB layout of the top (left) and bottom layers (right) for the RUG package.

Figure 10. RUG package top layer (left) and bottom layer (right) PCB layout

The X2QFN (RUG) package has the following dimensions: 0.5-mm pin pitch, 0.37-mm maximum height,

1.5-mm length, and 2.0-mm width.

3.5 RUC Package

Figure 11 displays the PCB layout of the top (left) and bottom layers (right) for the RUC package.

Figure 11. RUC package top layer (left) and bottom layer (right) PCB layout

The X2QFN (RUC) package has the following dimensions: 0.4-mm pin pitch, 0.35-mm maximum height,

2.0-mm length, and 2.0-mm width

www.ti.com

EVM Description and PCB Layout

SBOU215–January 2019

SMALL-AMP-DIP Evaluation Module (EVM)

3.6 RGY Package

Figure 12 displays the PCB layout of the top (left) and bottom layers (right) for the RGY package.

Figure 12. RGY package top layer (left) and bottom layer (right) PCB layout

The VQFN (RGY) package has the following dimensions: 0.5-mm pin pitch, 0.9-mm maximum height, 3.5-

mm length, and 3.5-mm width.

3.7 RTE Package

Figure 13 displays the PCB layout of the top (left) and bottom layers (right) for the RTE package.

Figure 13. RTE package top layer (left) and bottom layer (right) PCB layout

The WQFN (RTE) package has the following dimensions: 0.5-mm pin pitch, 0.75-mm maximum height,

3.0-mm length, and 3.0-mm width.

Bill of Materials and References

www.ti.com

10 SBOU215–January 2019

Submit Documentation Feedback

SMALL-AMP-DIP Evaluation Module (EVM)

4 Bill of Materials and References

4.1 Bill of Materials

Designator QTY Description Part Number

PCB 1 Printed-Circuit-Board SMALL-AMP-DIP-EVM

Header Strips 2 Header, 2.54 mm, 32 × 1,

Gold, TH TS-132-G-AA

4.2 References

(1) DIYAMP-EVM Tool Folder

(2) DUAL-DIYAMP-EVM Tool Folder

(3) DIP Adapter EVM Tool Folder

(4) TI Precision Labs Training

Table of contents

Other Texas Instruments Motherboard manuals

Texas Instruments

Texas Instruments DAC8801/11EVM User manual

Texas Instruments

Texas Instruments MMWAVE-DEVPACK User manual

Texas Instruments

Texas Instruments DP83869 User manual

Texas Instruments

Texas Instruments INA219EVM User manual

Texas Instruments

Texas Instruments Stellaris LM3S9B90 Manual

Texas Instruments

Texas Instruments TMDSEVM6678L User manual

Texas Instruments

Texas Instruments MSP430FR6043 User manual

Texas Instruments

Texas Instruments TPS65280EVM User manual

Texas Instruments

Texas Instruments TM4C Series User manual

Texas Instruments

Texas Instruments TVP9900EVM User manual

Texas Instruments

Texas Instruments TPS61040EVM User manual

Texas Instruments

Texas Instruments TPS7A3301EVM-061 User manual

Texas Instruments

Texas Instruments TPS281C100 User manual

Texas Instruments

Texas Instruments DLP LightCrafter Display 3010 User manual

Texas Instruments

Texas Instruments TPS1HC30-Q1 User manual

Texas Instruments

Texas Instruments TAS5731EVM User manual

Texas Instruments

Texas Instruments MSP-EXP432P401R User manual

Texas Instruments

Texas Instruments TSW1200EVM User manual

Texas Instruments

Texas Instruments BQ24450EVM User manual

Texas Instruments

Texas Instruments ADS8028EVM-PDK User manual

Texas Instruments

Texas Instruments BQ25616J User manual

Texas Instruments

Texas Instruments TMS320DM365 EVM User manual

Texas Instruments

Texas Instruments LMK5B33216EVM User manual

Texas Instruments

Texas Instruments DRV8701EVM User manual

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 user guide