StarTech.com PCI4S9503V Manual

3.3 Volt/5 Volt Buffered High Speed Serial

PCI Card

PCI4S9503V

PCI8S9503V Instruction Guide

The Professionals’ Source For Hard-to-Find Computer Parts

SERIAL CARD

* Actual product may vary from photo

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SCO OpenServer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Introduction

Thank you for purchasing a 3.3 volt/5 volt buffered high-speed serial card from

StarTech.com. Compatible with both 3.3 or 5 volt motherboards, this card adds either

four (PCI4S9503V) or eight (PCI8S950V) high-speed RS-232 ports to your system. The

card uses a 16-Byte buffer in both the receive and transmit channels simultaneously,

reducing the number of CPU interrupts and improving system performance.

Features

•Adds high speed RS-232 serial ports to your computer

•Works with both 3.3 volt and 5 volt server slots

•Complies with Universal 32 bit PCI bus and PCI Bus Version 2.2 specifications

•Compatible with most major OS platforms including Windows, Linux and UNIX

•Provides transfer rates of up to 115 KBytes/sec

•Uses only one IRQ assigned by the PCI BIOS

Before You Begin

To ensure a quick and easy device installation, please read through this section carefully

before attempting to install the device.

Requirements

•Acomputer running Windows XP/2000/NT/Me/98/95, DOS, Linux or SCO Open

Server

•An open 3.3 or 5V PCI slot

Contents

•1x serial card

•1x serial cable with DB9 connectors

•Driver disks for Windows, Linux, and Unix

Note: Depending on the driver version, you may also see this referred to as the P584 or

the PCIPORT on the driver disk.

Installation

Note: In one system, you can install two of these serial cards. You must differentiate

between the two cards by using the jumper (located near the end of the card). The card

with the jumper ON will be card number 1. The card with the jumper OFF will be card

number 2. Install the cards one at a time, starting with the card you want to be

designated number 1.

Installing the Card

1. Make sure that your system is unplugged and you are grounded.

2. Remove the cover of your system (see your computer's user manual for details, if

necessary) and gently turn your computer onto its side.

3. Locate an empty PCI slot (usually white in colour) and remove the metal plate that

covers the rear bracket. You may need a Phillips screwdriver to perform this step.

Hang on to the screw! You will need it to secure the card later.

4. Gently insert the card into the empty slot, making sure it is firmly seated.

5. Secure the card in place using the screw you removed in Step 3 and put your

computer case back on.

6. Plug the 37-pin end of the serial cable into the port on the card.

7. Turn the computer on.

Driver Installation

Note: Depending on your operating system and the configuration of your system, the

instructions below may not be identical to what you see on your screen.

Windows

Windows XP/2000

Once you turn your computer on after installing the card, Windows will automatically

detect the new hardware. Follow the onscreen prompts and direct Windows to the

Win2000 folder on the driver disk (Windows 2000 and Windows XP use the same driver).

Notes:

•To change the COM port number: Windows will automatically assign the card a

COM port number. If you need to specify another port number, you can use the setup

utility included with the driver. Go to: Control Panel/System/Hardware/Device

Manager/Multi-Port Serial Adapter/Setup. From here you will be able to set the

target value.

•Each serial card needs an open IRQ for Plug and Play function.

Windows NT

Before you begin the installation, make sure you are logged in as a user with

administrative privileges.

1. Start the Control Panel applet by double-clicking on its icon in the Program Managers

main group.

2. Double-click the Network icon to bring up the Network Control Panel applet.

3. Select Add Adapter. A list of possible adapters will be displayed. Select “Other:

Requires disk from manufacturer.”

4. When prompted for the path, specify the location of the driver for the card you

installed. Depending on your version of the driver disk, the drivers may be found in

the P584/NT4 folder.

5. Follow the onscreen prompts to complete installation. Make sure that the COM port

number does not conflict with any other devices in your system.

6. Use the “Binding” function to make more serial ports available. If you do not perform

a binding function, you may not have an extra COM port available in your next boot

procedure.

Notes:

•When installing two cards in the same system, the card with the jumper ON will be

assigned the lower COM port number. The card with the jumper OFF will have the

higher COM port number.

Windows Me/98/95

Once you turn your computer on after installing the card, Windows will automatically

detect the new hardware. Follow the onscreen prompts and direct Windows to the Win95

folder on the driver disk (Windows Me, 98, and 95 use the same driver).

Notes:

•After you install the driver, you may get another message saying that new hardware

has been found. You do not need to install the driver again.

•Each serial card needs an open IRQ for Plug and Play function.

•In Windows 98, you need to assign the card to COM 5 or higher, because COM 3/4

has been reserved for a legacy COM port.

DOS

When installing multiple cards in DOS, it is important to install the card designated card

Number 1 (with the jumper ON) first.

1. Change your active directory to the target directory:

ex: c:\RAYON

2. Insert the driver disk into the disk drive and copy the DOS files from the driver

diskette:

ex: xcopy /s/e/v a:\DOS\*.*

3. Run the driver installation command:

ex: c:\rayon\pciport

4. The cards will now be installed in your system. Each card will show the card number

in the system (for the application to specify the target card and target port), the card

model, the card jumper setting (for card number 1 or 2), the IRQ assigned, and the

COM port number for the card.

You may see the following error messages:

•PCIPORT already installed. This means the driver has already been installed.

•Please check the “JP1”. This means that both cards in the system have their jumpers

ON.

•PCIPORT not in system. There is no card in the PCI slot.

Notes:

•The driver function call description can be found on the DOS driver diskette. There is

also a DEMO program for the user to meet their target application program.

LINUX

1. Login as super-user (SU) or root.

2. Change your directory to root and copy the driver diskette to the system:

# cd /

# tar xvf /dev/fd0

3. Change the directory to /etc/pciport and run the Install command:

# cd /etc/pciport

# ./Install

4. Follow the prompts to perform the following:

• Choose your Linux kernel version

• Rebuild your system

• Exit and reboot with new settings

The device name will be /dev/tty8[1--2] [a--h]

Card Definitions

Note: Card 1 is the card with the jumper ON.

I/O Port Number Definitions

For example, the device named /dev/tty82b is the device plugged into port B on card

Number 2.

Notes:

•The above installation procedure installs a module type driver. If you can not install

the driver successfully, you may need to use a kernel type driver. You will need to

enter the Build directory and run Install again. In kernel type drivers, you may need

to have the full source file for the Linux system to be re-compiled.

•Each serial card needs an open IRQ for Plug and Play function.

Card Number Device Name

1tty81?

2tty82?

Port Number Device Name

Atty8?a

Btty8?b

Ctty8?c

Dtty8?d

Etty8?e

Ftty8?f

Gtty8?g

Htty8?h

SCO OpenServer

1. Log in as a super-user (SU) or root.

2. Extract all the files on the diskette using the tar command:

# cd /

# tar xvf /dev/fd0135ds18

3. Change the directory to /etc/pciport and run the Build command:

# cd /etc/pciport

# ./build

4. Reboot your system.

The device name will be /dev/tty8[1--2] [a--h]

Card Definitions

Note: Card 1 is the card with the jumper ON.

I/O Port Number Definitions

For example, the device named /dev/tty82b is the device plugged into port B on card

Number 2.

Notes:

•The resources for the card are assigned by the PCI BIOS. If your environment has

changed, you may need to run the Build command again to remove the old driver

and reinstall it again.

•Each serial card needs an open IRQ in order to function properly.

Card Number Device Name

1tty81?

2tty82?

Port Number Device Name

Atty8?a

Btty8?b

Ctty8?c

Dtty8?d

Etty8?e

Ftty8?f

Gtty8?g

Htty8?h

Other manuals for PCI4S9503V

This manual suits for next models

Table of contents

Other StarTech.com PCI Card manuals

StarTech.com

StarTech.com PCIPOST Manual

StarTech.com

StarTech.com PEX4S952LP User manual

StarTech.com

StarTech.com PEXMSATA3422 User manual

StarTech.com

StarTech.com UVCHDCAP User manual

StarTech.com

StarTech.com PEX1000MMSC User manual

StarTech.com

StarTech.com PEX8S1050LP User manual

StarTech.com

StarTech.com PCIIDE2 System manual

StarTech.com

StarTech.com PCI2S232485I User manual

StarTech.com

StarTech.com PCIESATA2I User manual

StarTech.com

StarTech.com PCISCSI2 User manual

StarTech.com

StarTech.com PEX1PECP User manual

StarTech.com

StarTech.com PCI2S650DVLP User manual

StarTech.com

StarTech.com PEXUSB3S4 System manual

StarTech.com

StarTech.com PEX2S650 User manual

StarTech.com

StarTech.com PEXUSB4DP User manual

StarTech.com

StarTech.com PEXUSB3S44V User manual

StarTech.com

StarTech.com PCI1S550 User manual

StarTech.com

StarTech.com PCISATA2 User manual

StarTech.com

StarTech.com PCI1P2 User manual

StarTech.com

StarTech.com SVID2USB232 User manual

StarTech.com

StarTech.com PEX1TO16R User manual

StarTech.com

StarTech.com PEX1000MMSC User manual

StarTech.com

StarTech.com PEX867WAC22 User manual

StarTech.com

StarTech.com PEXUSB311AC2 User manual

Popular PCI Card manuals by other brands

ERMA

ERMA SSI 1417 instruction manual

SIIG

SIIG CyberSerial Dual PCI Software installation

Moxa Technologies

Moxa Technologies CP-102E Quick installation guide

I-Bus

I-Bus IBC2602 user guide

Exsys

Exsys EX-60102 manual

Chelsio Communications

Chelsio Communications T5 Series Installation and user guide

Conrad Electronic

Conrad Electronic 97 46 71 operating instructions

Micro Innovations

Micro Innovations USB650A Quick installation guide

KTI Networks

KTI Networks KF-310 user guide

Asus

Asus SpaceLink WL230 user manual

SIIG

SIIG SC2475 Quick installation guide

TRENDnet

TRENDnet TEW-703PI Quick installation guide

Belkin

Belkin F5D7000F user manual

Pericom

Pericom PI7C7100 manual

ADLINK Technology

ADLINK Technology cPCI-3548 user manual

Digium

Digium TE200 Series user manual

Allo.com

Allo.com 2nd Gen E1/T1/J1 Quick installation guide

Western Digital

Western Digital FireWire PCI Adapter installation guide