Speco O4MD3 User manual
Quick Start Guide
O4MD3
1Warning and Caution
■ If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to disassemble
the camera yourself. Any unauthorized changes or modifications
could void the warranty.
■ Do not allow water or liquid intrusion into the camera.
■ All installation and operation here should conform to local
electrical safety codes. Make sure the device is firmly installed
on the wall or ceiling.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use cleaning cloth to wipe it
gently.
■ Do not aim the camera at the sun or extremely bright light
sources.
■ Do not place the camera in extremely hot or cold environments
and dusty and damp locations . Do not expose it to highly
electromagnetic radiation.
■ Do not block any ventilations.
Package
2
Overview
3 Overview
3
Ethernet connector
CVBS connector
Reset
Micro SD card slot
MIC in connector
DC power connector
1
2
6
5
3
4
Camera Quick start guide
CD Plastic plug ×2
Drill template Wall mounting bracket
Screwdriver
2 tapping screws PA 4×25
1
2
3
4
5
6
* 1 It is recommended to install the security cap for outdoor installations.
* 2 DC 12V power supply is not required if a PoE switch or injector is used to power
the camera.
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.
DC12V
2
13
Security Cap
Installation
4
* Before you start, please make sure that the wall or ceiling is strong enough
to withstand three times the weight of the camera and bracket.
① Loosen the lock screw of the bracket and then remove the
mounting base from the bracket.
② Loosen the screws to remove the lower dome from the camera.
Lower Dome
Lock screw
Mounting base
③ Pull the cables through the bracket. Then fix the camera onto the
bracket with the screws provided.
④ Fix the mounting base of the bracket onto the wall with the screws.
⑥Adjust the camera to obtain an optimum angle . Before adjustment,
preview the image of the camera on a monitor.
⑤ Connect the cables. Then attach the bracket onto the mounting
base and fasten them with the lock screw.
Rotation 0°~350°
Pan 0°~360°
Tilt 0°~70°
Web Operation and Login
5
● Operation
IP Scanner can search for the device on the local network.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.
⑦ Install the lower dome back to the camera with the screws.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins.
O4 MD3
Table of contents
Other Speco Security Camera manuals
Speco
Speco O2P12X User manual
Speco
Speco VL-67/W User manual
Speco
Speco Intensifier O2iBD3 User manual
Speco
Speco CVC-1705 User manual
Speco
Speco VL-634 User manual
Speco
Speco H8D7M User manual
Speco
Speco O2P20X User manual
Speco
Speco Deterrent O4TDD1M User manual
Speco
Speco WDRB10H User manual
Speco
Speco CVC-770PH User manual
Speco
Speco CVC-5735DNV User manual
Speco
Speco CVC6146SCS Series User manual
Speco
Speco CVC-628M User manual
Speco
Speco HTSD12X User manual
Speco
Speco SIPT5 User manual
Speco
Speco O8D7M User manual
Speco
Speco CVC-770PHSCS User manual
Speco
Speco O2iD9 User manual
Speco
Speco O2D5M User manual
Speco
Speco CVC-625WP User manual
