Siemens UP 520/31 User manual

GAMMA instabus

Technical Product Information

February 2010

Blind actuator UP 520/31 5WG1 520-2AB31

Siemens AG UP 520/31, 4 pages Technical Manual

Industry Sector, Building Technologies

Low Voltage Distribution © Siemens AG 2010 Update: http://www.siemens.com/gamma

PO Box 10 09 53, D-93009 Regensburg Subject to change without further notice

2.10.1.18/1

Product and Function Description

Photo

The blind actuator receives telegrams from sensors via the

Instabus and controls a shutter or blind motor with its

output. Both travel directions are mechanically

interlocked. With sun protection or positioning telegrams,

the actuator offers moreover the possibility of moving

shutters, blinds and slats into any desired position. On

reception of a storm warning, the actuator is capable of

moving shutters or blinds into a predefined safety position

and to lock them up in this position.

In addition, the device has two extension inputs that

depending on parameter settings, can act directly on the

output (local operation, see “state of delivery”) or

alternatively also as binary inputs on the Instabus. The

connected potential-free switch or push button contacts

are read in via a common reference potential on the

actuator. As binary input, telegrams can be transmitted for

switching or dimming, for Venetian blind control, value

setting or scene recall / save.

State of delivery:

•When delivered, the switching state of the outputs is

undefined.

•On application of the bus voltage, the relays will switch

off.

•With the bus voltage applied, the extension inputs

control the relays of the actuator as follows:

input Operation behavior

short stop / slat up

A long move up

short stop / slat down

B long move down

Simultaneous actuation of A and B is not possible

Application program

12 A1S2 Shutter, 2x Input 207301

•2 binary inputs

oON / OFF / TOGGLE switching

oValue setting

oDimming

oBlind / Shutter – control

oScene control

oInputs blocking function

oBehavior on bus power restoration

•1 channel with additional functions

oSun protection function

oSafety function

oAdjustable response after bus voltage

failure

oAdjustable response to bus voltage return

oAdjustable priority of sun protection

function and manual operation

GAMMA instabus

Technical Product Information

February 2010

Blind actuator UP 520/31 5WG1 520-2AB31

Technical Manual UP 520/31, 4 pages Siemens AG

Industry Sector, Building Technologies

Update: http://www.siemens.com/gamma © Siemens AG 2010 Low Voltage Distribution

Subject to change without further notice PO Box 10 09 53, D-93009 Regensburg

2.10.1.18/2

Technical specifications

Power supply

•Carried out via the bus line

•Power consumption: typically 150 mW

Outputs

•Number: 1 output, potential-free relay contact (µ-contact)

•Rating voltage: AC 230V,

•Switching power: max. 1 motor 1000 VA

•Switching behavior: Can be parameter set, depending

on function

Contacts

•Output: Contact the load on H07V-K 1,5 mm2with the

attached clamps.

•Inputs and bus line: Line YY 6x0.6 mm

Approx. 33cm pre-assembled, can be laid to max. 5m

Mechanical specifications

•Casing: plastic

•Dimensions: d =53mm, height = 28 mm

•Weight: approx. 88g

•Mounting: in box mounts, Ø 60mm, depth: 40mm

Electrical safety

•Degree of pollution (to IEC 60664-1): 2

•Protection class (to EN 60529): IP 20

•Protection class (to IEC 61140): III

•Overvoltage category class (to IEC 60664-1): III

•Bus: safety extra low voltage SELV DC 24V

•Device complies with EN 50090-2-2 and IEC 60664-1

Reliability

Failure rate: 170 fit at 40°C

EMC criteria

•Complies with EN 61000-6-2, EN 61000-6-3 and EN

50090-2-2

Environmental specifications

•Climatic conditions: EN 50090-2-2

•Ambient temperature in operation: - 5 ... + 45 °C

•Storage temperature: - 25 ... + 70 °C

(Storage above + 45°C reduces the service life)

•Relative humidity (non-condensing): 5% to 93%

Markings

•KNX EIB

CE mark

•to EMC directive (residential and functional building)

Location and functioning of the display and

operating elements

PKBK

EIB+ / RD

EIB- / BK

A / GN

com / WH

B / YE

com / BN

Prog.

U 230V

Figure 1: Location of the indicating and operating elements

X Connector cables low voltages

Red: Bus (+)

Black: Bus (-)

Green: input A

White: Reference potential (com)

Yellow: Input B

Brown: Reference potential (com)

Y Connector cables load

black: L // brown: Up // pink: Down

Z Program button / -LED (red)

GAMMA instabus

Technical Product Information

February 2010

Blind actuator UP 520/31 5WG1 520-2AB31

Siemens AG UP 520/31, 4 pages Technical Manual

Industry Sector, Building Technologies

Low Voltage Distribution © Siemens AG 2010 Update: http://www.siemens.com/gamma

PO Box 10 09 53, D-93009 Regensburg Subject to change without further notice

2.10.1.18/3

Mounting and wiring

ÆGeneral:

It is recommended that the actuator is installed in two

flush sockets connected to one another (cf. fig. 2). One

socket (A) can accommodate, e.g., a series switch (C) as

well as the bus and extension connection. The other

socket (B) accommodates the actuator and the 230 V

terminals. The 6-pole connection lead (D) is guided

through the socket connection.

230 V

Figure 2

230 V

Bus/Com/A,B

> 4 mm

Figure 3

VDanger

•The device must be mounted and commissioned

by an authorized electrician.

•When connecting the device, it should be

ensured that the device can be isolated.

•The device must not be opened.

•For planning and construction of electric

installations, the relevant guidelines, regulations

and standards of the respective country are to be

considered.

•During installation, ensure adequate insulation

between mains voltage and bus or extensions! A

minimum spacing should be maintained

between bus / extension cable cores and mains

voltage cable cores of at least 4 mm.

(cf. figure 3)

ÆInputs:

Two extension inputs can be used for the connection of

potential-free contacts for local control or as binary inputs.

(cf. figure 4)

Line YY 6x 0.6 mm

Approx. 33cm pre-assembled, can be laid to max. 5m

COM

U = - 19 V (ca./approx.)

com

UCOM

rot / red

schwarz / black

grün / green

weiß / white

gelb / yellow

braun / brown

KNX

(-)

(+)

Figure 4

Caution

•To avoid disruptive EMI irradiation, the lines of the

inputs should not be laid parallel to lines conducting

mains voltage.

•Input A (green), input B (yellow) and reference

potential (com) (white and brown) must not

connect to inputs or reference potential (com) of

other devices.

VDanger

•On no account should you connect mains voltage

(230 V) or other external voltages to the extension

inputs! Connection to an external voltage would

endanger the electrical safety of the entire KNX/EIB

system (SELV / no galvanic isolation)!

People can be at risk, equipment and devices can be

destroyed!

•Unused cable cores of the 6-pole connection lead

are to be insulated from one another and from

external voltages.

GAMMA instabus

Technical Product Information

February 2010

Blind actuator UP 520/31 5WG1 520-2AB31

Technical Manual UP 520/31, 4 pages Siemens AG

Industry Sector, Building Technologies

Update: http://www.siemens.com/gamma © Siemens AG 2010 Low Voltage Distribution

Subject to change without further notice PO Box 10 09 53, D-93009 Regensburg

2.10.1.18/4

ÆOutputs:

A blind actuator is switching an electrical drive, which is

configured for two rotating directions (Up/Down). (cf.

figure 5)

PKBNBK

EIB+ / RD

EIB- / BK

A / GN

com / WH

B / YE

com / BN

Prog.

Un~ 230V

Figure 5

Note

•The outputs of the blind actuator are electrical

interlocked

VDanger

•The soldered end of lines have to connect by using

the attached clamps.

•Do not connect three-phase AC motors to blind

actuators

•Observe the instructions of the motor

manufacturers if motors are to be connected in

parallel. Otherwise risk of irreparable damage to

the motors.

•Use only blinds or shutters with limit switches

(mechanical or electronic). The limit switches of

the connected motors must be checked for correct

adjustment.

Dimensioned picture

Dimensions in mm

Figure 6

Ø = 53 mm

Height = 28 mm

General notes

•Any faulty device is to be returned to the local Siemens

office.

•If you have further questions concerning the product,

please contact our Technical Support:

℡+49 (0) 180 50 50-222 (0,14 €/min. from the German

landline network, deviating mobile communications

prices are possible)

+49 (0) 180 50 50-223

E-Mail: support.automation@siemens.com

Internet: www.siemens.com/automation/service&support

Other Siemens Controllers manuals

Siemens

Siemens 5WG1 530-1DB31 User manual

Siemens

Siemens DELTA i-system User manual

Siemens

Siemens SINUMERIK 840DE User manual

Siemens

Siemens N 567/01 User manual

Siemens

Siemens SINAMICS S120 Technical Document

Siemens

Siemens GDB 9E Series User manual

Siemens

Siemens GEB 1 Series User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens SIMATIC S7-1200 User manual

Siemens

Siemens 27086-TAB Owner's manual

Siemens

Siemens ACR12.3 1 Series User manual

Siemens

Siemens Stratos Outstation User manual

Siemens

Siemens QAA75 series User manual

Siemens

Siemens DXR2.E10PL-102BK User manual

Siemens

Siemens SINAMICS G130 User manual

Siemens

Siemens RMH760 User manual

Siemens

Siemens SIRIUS 3RA2110 Series User manual

Siemens

Siemens Desigo PXC4.E16 User manual

Siemens

Siemens OpenAir GLB141.1P Owner's manual

Siemens

Siemens MO310 User manual

Siemens

Siemens RVP360 Operator's manual

Siemens

Siemens SCALANCE M800 User manual

Siemens

Siemens SITRANS LUT400 User manual

Siemens

Siemens BACNET 125-699 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide