Siemens RVP201 User manual

Building Technologies B2464en 74 319 0613 0 b 22.01.2008

Energy-efficient heating with

the RVP201/211 heating controller

Operating Instructions

You want to switch the heating on

1. Is the plant ready to operate? Check the mains

switch.

2. Check the time of day and – with the 7-day time

switch – the weekday. Make readjustments, if neces-

sary (refer to the following section).

3. Move the operating mode selector to the required

Auto mode.

You want to set the clock

The switching dial may only be turned clockwise, never

anti-clockwise!

1. First, make a coarse setting:

Turn the switching dial slowly in clockwise direction

until the current time of day reaches the time indicator

(with the 7-day dial, also observe the weekday).

2. Now make the correct setting:

Turn the large hand until the time of day is correct.

Tip: The change from wintertime to summertime, and vice

versa, must be made manually.

You want to heat in automatic mode Auto

The controller has two Auto modes:

Automatic changeover between NORMAL tem-

perature and heating control OFF according to the

24-hour program.

Automatic changeover between NORMAL and

REDUCED temperature according to the 24-hour

program.

You want no heating for a certain

period of time

Move the operating mode selector to . The control is

switched off, but ready to operate.

Only with the RVP211: Select either

for control switched off, or

automatic d.h.w. heating, control switched off

Tip: Frost protection is ensured in all operating modes.

Meaning of LED “Override”

-“Override” flashes: A fault has occurred – refer to the

section covering operational faults

-“Override” steady on: Controller is controlled by the

room unit. The settings used are those made on the

room unit. There is no fault

You want to heat continuously Auto

-No setback: Select operating mode

-Continuous setback: Select operating mode

Tip: Do not forget to reset the operating mode!

Your rooms are too cold or too warm

Especially in mild weather:

Readjust the room temperature with setting knob . One

point represents a room temperature change of 2 °C.

Especially in cold weather:

Readjust the slope of the heating curve with setting knob :

-Room temperature too high: Reduce slope by about 0.2

-Room temperature too low: Raise slope by about 0.2

Building Technologies B2464en 74 319 0613 0 b 22.01.2008

Especially in the night:

Readjust the setback with setting knob . The scale indi-

cates the setback in °C against the NORMAL tempera-

ture.

Tip: Each time you make a room temperature readjust-

ment, wait two days; the controlled system needs

time to adapt.

Tip: Do not forget objects that are sensitive to low tem-

peratures, such as plants.

You want to change the heating periods

For digital time switch: please refer to separate instructions.

Set the periods of time for the NORMAL temperature and

REDUCED/OFF with the switching dial using the tilting

riders:

-For periods of time with NORMAL temperature:

Tilt riders outward

-For periods of time with REDUCED temperature or

OFF: Tilt riders inward

Tip: Before making any settings: Prepare a heating

schedule.

Only with the RVP211: You want to

change the DHW temperature

Readjust the DHW temperature with the setting knob .

Recommended setting: 55 to 60 °C.

Tip: Excessive temperatures lead to more scale buildup.

Your heating system responds in an

unusual manner

-In the event of a power failure, the clock will make up

for the lost time when power returns.

You can cancel catching up by briefly setting the selec-

tor to and then back again to the required operating

mode. Then, readjust the clock

-Temperature does not change: Check the operating

mode; automatic setback and heating up with only one

Auto mode

-Room unit (if present) is inactive: Check the controller's

operating mode – it must be an Auto mode!

-Required temperature is reached either too early or to

too late: Change the 24-hour program

Tip: Well insulated buildings have a great thermal inertia.

What to check in the case of operational

faults

-Are all fuses of the plant in order?

-Is sufficient fuel in the tank?

-Have the controller settings (e. g. the setpoints) been

changed?

-Does the green LED “Override” flash? Reason: Flow or

boiler temperature sensor faulty / not connected, or

outside and room temperature sensor

faulty / not connected. Select operating mode and

call in your heating engineer

-Has the burner gone to lockout? If yes, press the reset

button

Energy saving tips

-Do not allow room temperatures to exceed 21 °C dur-

ing the day

-Air the rooms for only short periods of time, but with the

windows fully open

-Set the thermostatic radiator valves in unoccupied

rooms to the frost protection position

-Make certain there are no curtains, furniture, etc., in

front of the radiators

-Close shutters and blinds whenever possible

-Check the consumption of heat on a regular basis

Other manuals for RVP201

This manual suits for next models

Table of contents

Other Siemens Controllers manuals

Siemens

Siemens OpenAir GCA Series Owner's manual

Siemens

Siemens DE406M Series User manual

Siemens

Siemens SIRIUS 3RW40 5 User manual

Siemens

Siemens SIRIUS 3RW44 User manual

Siemens

Siemens GDB 9E Series User manual

Siemens

Siemens SIMATIC S5-95F User manual

Siemens

Siemens DOL 3TW7291-1A Guide

Siemens

Siemens REV13 series User manual

Siemens

Siemens SQS35.53 User manual

Siemens

Siemens SlMATlC S5-010W User manual

Siemens

Siemens RUGGEDCOM WIN5214 User manual

Siemens

Siemens Flowrite 599 Series User manual

Siemens

Siemens REV23.03RF User manual

Siemens

Siemens Albatros2 RVA78.690 User manual

Siemens

Siemens SIMOTION C230-2 Technical Document

Siemens

Siemens TIM 1531 IRC User manual

Siemens

Siemens RVA63.242 User manual

Siemens

Siemens SIMATIC NET CP 1613 A2 User manual

Siemens

Siemens BT300 LonWorks User manual

Siemens

Siemens RDF870KN User manual

Siemens

Siemens SIMATIC S7-200 User manual

Siemens

Siemens 340 User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens RBC User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide