Siemens SINAMICS S120 Technical Document
Equipment Manual 04/2004 Edition
SINAMICS S120
Control Units and
A
dditional System Components
Preface
System Overview
1
Control Units
2
Additional System
Components
3
Sensor System Connection
4
Appendix A
A
Appendix B
B
Appendix C
C
SINAMICS
SINAMICS S120
Equipment Manual for Control Units
and Additional System Components
Equipment Manual
(GH1), 04.2004 Edition
SINAMICS® Documentation
Printing history
Brief details of this edition and previous editions are listed below.
The status of each edition is shown by the code in the "Remarks" column.
Status code in the "Remarks" column:
A New documentation
B Unrevised reprint with new order no.
C Revised edition with new status
If factual changes have been made on the page in relation to the same software version, this is indicated by a new edition
coding in the header on that page.
Edition Order No. Remarks
04.04 6SL3097-2AH00-0BP0 A
Trademarks
SIMOVERT®, SIMATIC®, SIMATIC HMI®, SIMATIC NET®, SIMOTION®, SINUMERIK® and SINAMICS® are trademarks of
Siemens. Other product names used in this documentation may be trademarks which, if used by third parties, could infringe the
rights of their owners.
Further information is available on the Internet under:
http://www.siemens.com/motioncontrol
This publication was produced with SIPS+
The reproduction, transmission or use of this document or its contents is not
permitted without express written authority. Offenders will be liable for
damages. All rights, including those created by patent grant or registration of a
utility model or design, are reserved.
© Siemens AG, 2004. All rights reserved
We have checked that the contents of this document correspond to the hardware
and software described. Nonetheless, differences might exist and therefore we
cannot guarantee that they are completely identical. The information contained in
this document is, however, reviewed regularly and any necessary changes will
be included in the next edition. We welcome suggestions for improvement.
Subject to changes without prior notice
Order No. 6SL3097-2AH00-0BP0
Printed in Germany
Siemens Aktiengesellschaft
Equipment Manual for Control Units and Additional System Components
Equipment Manual, (GH1), 04.2004 Edition, 6SL3097-2AH00-0BP0 iii
Preface
Preface
Information on the SINAMICS S documentation
The SINAMICS S documentation is divided into the following areas:
• General documentation/catalogs
• Manufacturer/service documentation
• Electronic documentation
This documentation is an integral part of the manufacturer/service documentation developed
for SINAMICS. All documents can be obtained separately.
You can obtain detailed information about the documents named in the documentation
overview and other documents available for SINAMICS from your local Siemens office.
For the sake of simplicity, this documentation does not contain all detailed information about
all types of the product and cannot cover every conceivable case of installation, operation, or
maintenance.
The contents of this documentation are not part of an earlier or existing agreement, a
promise, or a legal agreement, nor do they change this. All obligations entered into by
Siemens result from the respective contract of sale that contains the complete and sole valid
warranty arrangements. These contractual warranty provisions are neither extended nor
curbed as a result of the statements made in this documentation.
Audience
This documentation is aimed at machine and plant builders, commissioning engineers, and
service personnel who use SINAMICS.
Objective
This manual describes the hardware components of the SINAMICS S system. It provides
information about installation, electrical connection, and cabinet design.
Preface
Equipment Manual for Control Units and Additional System Components
iv Equipment Manual, (GH1), 04.2004 Edition, 6SL3097-2AH00-0BP0
Danger and warning notices – symbol explanations
The following danger and warning notices are used in this document:
Danger
Indicates an imminently hazardous situation which, if not avoided, will result in death, serious
injury, or substantial damage to property.
Warning
Indicates an potentially hazardous situation which, if not avoided, could result in death, or
serious injury, or substantial property damage.
Caution
Used with the safety alert symbol indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or property damage.
Caution
Used without safety alert symbol indicates a potentially hazardous situation which, if not
avoided, may result in property damage.
Notice
Used without the safety alert symbol indicates a potential situation which, if not avoided, may
result in an undesirable result or state.
Note
This notice indicates that there are further issues to be taken into consideration.
Preface
Equipment Manual for Control Units and Additional System Components
Equipment Manual, (GH1), 04.2004 Edition, 6SL3097-2AH00-0BP0 v
Definition: Qualified personnel
With reference to this manual and the warning labels on the product, a "qualified person" is
someone who is familiar with the installation, mounting, startup, and operation of the
equipment and who has certified qualifications for the type of responsibility involved, such
as:
• Training and instruction, i.e. authority to switch on and off, to earth and to label circuits
and equipment according to safety regulations.
• Training and instruction in maintenance and use of adequate safety equipment according
to safety regulations.
• First aid training.
Finding information
To help you find information more easily, the following sections have been included in the
appendix in addition to the table of contents:
1. References
2. Index
Preface
Equipment Manual for Control Units and Additional System Components
vi Equipment Manual, (GH1), 04.2004 Edition, 6SL3097-2AH00-0BP0
Technical information
Hotline
If you have any further questions, please call our hotline:
A&D Technical Support
Tel.: +49 (0) 180 5050 - 222
Fax: +49 (0) 180 5050 - 223
E-mail: [email protected]
Please send any questions about the documentation (suggestions for improvement,
corrections, and so on) to the following fax number or e-mail address:
Fax: +49 (0) 9131 98 - 2176
Fax form: See feedback page at the end of this publication
E-mail: motioncontrol.[email protected]
Internet address
Up-to-date information about our products can be found on the Internet at the following
address:
http://www.siemens.com/motioncontrol
Other manuals for SINAMICS S120
94
Table of contents
Other Siemens Control Unit manuals
Siemens
Siemens SIMATIC S5 User manual
Siemens
Siemens SINAMICS G120P CU230P-2 Administrator guide
Siemens
Siemens ST950 User manual
Siemens
Siemens SIMATIC ET 200SP User manual
Siemens
Siemens SINUMERIK 840D sl User manual
Siemens
Siemens SICAM A8000 Series User manual
Siemens
Siemens SINAMICS G130 User manual
Siemens
Siemens Maxum II PD PA AP User manual
Siemens
Siemens P1 BIM User manual
Siemens
Siemens SENTRON PAC PROFIBUS DP User manual
Siemens
Siemens PSO 4000 User manual
Siemens
Siemens LMV 5 Series User manual
Siemens
Siemens S7-1500 PROFIBUS User manual
Siemens
Siemens 3VL9800-3MJ00 User manual
Siemens
Siemens SIMATIC NET RX1500 User manual
Siemens
Siemens LMO14 Series User manual
Siemens
Siemens Synco RMK770 User manual
Siemens
Siemens SINUMERIK 808D User manual
Siemens
Siemens EN100 User manual
Siemens
Siemens SIMATIC RF170C User manual
Popular Control Unit manuals by other brands
Festo
Festo Compact Performance CP-FB6-E Brief description
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Quick installation guide
JS Automation
JS Automation MPC3034A user manual
JAUDT
JAUDT SW GII 6406 Series Translation of the original operating instructions
Spektrum
Spektrum Air Module System manual
BOC Edwards
BOC Edwards Q Series instruction manual
KHADAS
KHADAS BT Magic quick start
Etherma
Etherma eNEXHO-IL Assembly and operating instructions
PMFoundations
PMFoundations Attenuverter Assembly guide
GEA
GEA VARIVENT Operating instruction
Walther Systemtechnik
Walther Systemtechnik VMS-05 Assembly instructions
Altronix
Altronix LINQ8PD Installation and programming manual
