Siemens SIMOCODE pro 3UF7902-0AA00-0 User manual

SIMOCODE® pro

Initialisierungsmodul

Initialization module

Module d’initialisation

Módulo de inicialización

Modulo di inizializzazione

Módulo de inicialização

3UF7902-0AA00-0

Betriebsanleitung Operating Instructions Instructions de service

Instructivo Istruzioni operative Instruções de Serviço

Deutsch English Français

Vor der Installation, dem Betrieb oder der

Wartung des Geräts muss diese Anleitung

gelesen und verstanden werden.

Read and understand these instructions

before installing, operating, or maintaining

the equipment.

Ne pas installer, utiliser ou intervenir sur cet

équipement avant d'avoir lu et assimilé les

présentes instructions et notamment les

conseils de sécurité et mises en garde qui y

figurent.

GEFAHR DANGER DANGER

Gefährliche Spannung.

Lebensgefahr oder schwere

Verletzungsgefahr.

Vor Beginn der Arbeiten Anlage und Gerät

spannungsfrei schalten.

Hazardous voltage.

Will cause death or serious injury.

Turn off and lock out all power supplying

this device before working on this device.

Tension électrique.

Danger de mort ou risque de blessures

graves.

Mettre hors tension avant d’intervenir sur

l’appareil.

VORSICHT CAUTION PRUDENCE

Eine sichere Gerätefunktion ist nur mit

zertifizierten Komponenten gewährleistet. Reliable functioning of the equipment is only

ensured with certified components.

La sécurité de fonctionnement de l'appareil

n'est garantie qu'avec des composants

certifiés.

Español Italiano Português

Leer y comprender este instructivo antes de

la instalación, operación o mantenimiento

del equipo.

Leggere con attenzione queste istruzioni

prima di installare, utilizzare o eseguire

manutenzione su questa apparecchiatura.

Ler e compreender estas instruções antes

da instalação, operação ou manutenção do

equipamento.

PELIGRO PERICOLO PERIGO

Tensión peligrosa.

Puede causar la muerte o lesiones

graves.

Desconectar la alimentación eléctrica antes

de trabajar en el equipo.

Tensione pericolosa.

Può provocare morte o lesioni gravi.

Scollegare l’alimentazione prima di eseguire

interventi sull'apparecchiatura.

Tensão perigosa.

Perigo de morte ou ferimentos graves.

Desligue a alimentação elétrica e proteja

contra o religamento, antes de iniciar o

trabalho no equipamento.

PRECAUCIÓN CAUTELA CUIDADO

El funcionamiento seguro del aparato sólo

está garantizado con componentes

certificados.

Il funzionamento sicuro dell'apparecchiatura

è garantito soltanto con componenti

certificati.

O funcionamento seguro do aparelho

apenas pode ser garantido se forem

utilizados os componentes certificados.

GWA 4NEB 631 6478-10 DS 01 Last update: 23 November 2011

3ZX1012-0UF70-2AA1

Technical Assistance: Telephone: +49 (911)-895-5900 (8°° - 17°° CET) SIEMENS AG

Fax: +49 (911)-895-5907 Technical Assistance

E-mail: technical-assistanc[email protected] Würzburger Str. 121

Internet: www.siemens.com/industrial-controls/technical-assistance D-90766 Fürth

3UF7970-0AA01-0

(Systemhandbuch

SIMOCODE pro)

3ZX1012-0UF70-1AB1

(Systemhandbuch

SIMOCODE PROFINET)

www.siemens.de/industrial-controls/support

3UF7970-0AA00-0

(System Manual

SIMOCODE pro)

3ZX1012-0UF70-1AC1

(System Manual

SIMOCODE PROFINET)

3UF7970-0AA02-0

(Manuel système

SIMOCODE pro)

3ZX1012-0UF70-1AD1

(Manuel système

SIMOCODE PROFINET)

ES Manual de sistema

SIMOCODE pro

3ZX1012-0UF70-1AE1

(Manual de sistema

SIMOCODE PROFINET)

Technische Änderungen vorbehalten. Zum späteren Gebrauch aufbewahren.

Subject to change without prior notice. Store for use at a later date.

3ZX1012-0UF70-2AA1

Farben beachten!

Observe colors!

Faire attention aux

couleurs!

Respetar los colores!

Rispettare i colori!

Observe as cores!

3UF7902-0AA00-03UF793.-0CA00-0

3UF7010* ≥E09 V3.1; 3UF7011* nur 3UF71* (inkl. 3UF7150*)

only 3UF71* (incl. 3UF7150*)

uniquement 3UF71* (y compris 3UF7150*)

solamente 3UF71* (incl. 3UF7150*)

solo 3UF71* (incl. 3UF7150*)

apenas 3UF71* (incl. 3UF7150*)

3UF793.-0CA00-0

Grundgeräte GG2 (3UF7010*) bis E08, V3.0 und alle Erzeugnisstände des GG1 (3UF7000*) unterstützen dieses Modul

nicht und laufen mit den internen Parametern an.

Basic units BU2 (3UF7010*) up to E08, V3.0, and all product versions of BU1 (3UF7000*) do not support this module and

start up with the internal parameters.

Les appareils de base GG2 (3UF7000*)jusqu'à E08, V3.0 et toutes les versions GG1 (3UF7010*) ne supportent pas ce

module et démarrent avec les paramètres internes.

Las unidades base UB1 (3UF7010*) hasta E08, V3.0 y todas las versiones de la UB1 (3UF7000*) no soportan este módulo

3UF7902-0AA00-0 y arrancan con los parámetros internos.

Le apparecchiature base GG2 (3UF7010*) fino a E08, V3.0 e tutte le versioni di prodotto del GG1 (3UF7000*) non sup-

portano questo modulo e si avviano con i parametri interni.

Os aparelhos base GG2 (3UF7010*) a E08, V3.0 e todas as variantes do GG1 (3UF7000*) não são compatíveis com esse

módulo e são iniciados com os parâmetros internos.

nach Bedarf

as required

au besoin

según necesidad

secondo le esigenze

conforme necessário

Befestigungslasche

Fastening strap

Patte de fixation

Lengüeta de fijación

Linguetta di fissaggio

Lingueta de fixação

Maßzeichnung

Dimension drawing

Dessin coté

Dibujo dimensional

Disegno quotato

Desenho de dimensões

3UF7902-0AA00-0

ุ





Other Siemens Control Unit manuals

Siemens

Siemens SITOP User manual

Siemens

Siemens SINUMERIK 828D Turning User manual

Siemens

Siemens RMB795 User manual

Siemens

Siemens SIMATIC ET 200SP Technical Document

Siemens

Siemens 4AI I 4WIRE HART Manual

Siemens

Siemens SINUMERIK 840D sl Quick start guide

Siemens

Siemens SIMATIC TI505 User manual

Siemens

Siemens HARS-T03 Series User manual

Siemens

Siemens SIMOTION D410-2 User manual

Siemens

Siemens CP 5611 User manual

Siemens

Siemens SENTRON 7KM PAC 4DI/2DO User manual

Siemens

Siemens 7XT71 Series User manual

Siemens

Siemens 3SB5 Instruction Manual

Siemens

Siemens SCALANCE S623 User manual

Siemens

Siemens SINUMERIK 840D Parts list manual

Siemens

Siemens SIMATIC NET RUGGEDCOM APE1808 Instruction sheet

Siemens

Siemens RAB10 Series User manual

Siemens

Siemens Flowrite 599 Series Owner's manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens LGB21.130A17 User manual

Siemens

Siemens K60 F Series User manual

Siemens

Siemens 3UF51 User manual

Siemens

Siemens SIMATIC NET User manual

Siemens

Siemens 3RA2816-0EW20 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual