Satel ASP-105 User manual

WIRELESS OUTDOOR SIREN

ASP-105

asp105_e 08/05

The ASP-105 wireless outdoor siren is designed for operation as part of the ABAX

two-way wireless system.

The optical and acoustic signaling are independently triggered by radio. A xenon lamp

(flash) is the source of light signal, while the sound signal is generated by means of

a piezoelectric transducer.

The ASP-105 outdoor siren is supplied with +12V (±15%) direct voltage. An

emergency power supply is the 6V 1.2Ah battery.

1. DESCRIPTION OF ELECTRONICS BOARD

Electronic circuit of the outdoor siren is made with the use of SMD technology and

impregnated against adverse effect of weather, which ensures a high reliability of the

device.

A tamper contact, which reacts to opening or pull-off of the housing from the surface,

is connected to the TMP terminals. The terminals +12V and COM are used to connect

the outer power supply.

The 3.15A fuse protects the battery power supply circuit.

The LED indicator is "on" in the TEST MODE only (see the ACU-100 controller manual)

to signal communication with the controller.

antenna red black

to battery to piezoelectric

transducer

LED indicator

fuse 3.15A

xenon lamp

Fig. 1. Outdoor siren electronics board

SATEL ASP-105

Placed on the electronics board is a label with 7-digit serial number, which must be

indicated when registering the outdoor siren in the system.

2. INSTALLATION

Prior to permanent mounting of the outdoor siren, you should check the level of signal

received from the siren by the ACU-100 controller and, if necessary, change place of

the installation so as to ensure optimal positioning in terms of communication.

The ASP-105 outdoor siren should be mounted on flat surface, at a high and hard-to-

access place, so as to minimize the risk of tamper. The device is to be attached to the

surface by using screws and expansion bolts.

In order to permanently install the wireless outdoor siren:

1. Remove the two screws locking the device cover.

2. Lift the cover by an angle of approx. 60° and remove it.

Caution ! The converter which supplies the optical signaling system generates high voltages

which may cause an electric shock. Therefore, observe safety precautions: carry

out the installation only with the battery disconnected, and connect the +12V

cable last.

3. Pass the 12V DC outer supply cable through the hole in the housing.

Fig. 2. View of outdoor siren housing

4. Using screws, secure the rear housing panel to the surface. It is advisable to keep

a clearance of minimum 2.5cm between the upper edge of the outdoor siren and

the ceiling or any element that may be situated above the device. Otherwise,

replacement of the cover may prove impossible.

5. Using a screw, secure the tamper element to the surface.

6. Using silicone, seal the mounting holes and the cable inlet opening.

cover locking screws

tamper contact

(to be screwed to surface)

screw

holes

cable inlet opening

ASP-105 ABAX 3

7. Connect the battery.

Note: The tamper alarm signaling will be blocked after activation of the service mode in case

of operation with INTEGRA series control panels, or activation of the TEST MODE in

any other configuration, as well as for 40 seconds after power-up of the siren.

8. Screw the outer supply cable to the terminals on the electronics board. The cable

should not be laid up in the close vicinity of the siren antenna, since it may cause

radio communication interference.

9. Replace the device cover and lock it with screws.

For information on registration and installation of the outdoor siren in the

wireless system - see the ACU-100 Controller User Manual.

3. TECHNICAL DATA

Operating frequency band..........................................................868.0MHz ÷ 868.6MHz

Nominal supply voltage ............................................................................12V DC ±15%

Current consumption (average):

- standby mode...............................................................................................30mA

- standby mode + battery charging...............................................................150mA

- optical signaling..........................................................................................165mA

- acoustic signaling .......................................................................................450mA

Inner battery...................................................................................................... 6V/1.2Ah

Inner battery protection................................................................................fuse T 3.15A

Operating temperature range....................................................................-20°C...+55°C

Housing dimensions .............................................................................. 148x254x64mm

DECLARATION OF CONFORMITY

Product:

ASP-105 - Outdoor Siren for ABAX System

Manufacturer: SATEL spółka z o.o.

ul. Schuberta 79

80-172 Gdańsk, POLAND

tel. (+48 58) 320-94-00

fax. (+48 58) 320-94-01

Product description:Wireless outdoor siren with battery backup, designed for interaction with the

controller of the ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency range,

supplied from a 3V lithium cell. The device is intended to be used in burglary and panic alarm

systems.

This product conforms to the following EU Directives:

R&TTE 1999/5/EC

This product meets requirements of the harmonized standards:

R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;

EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1

Safety: EN60950-1:2001

Notified body taking part in conformity evaluation:

Identification No.: 1471

Gdańsk, Poland 2005-07-15 Head of Test Laboratory:

MichałKonarski

The latest EC declaration of conformity and product approval certificates are available for

downloading on our website www.satel.pl

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.pl

Table of contents

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual