Satel SPL-5010 User manual
SPL-5010
OPTICAL-ACOUSTIC OUTDOOR SIREN
spl5010_en 10/16
The SPL-5010 siren provides information about alarm situations by means of optical and
acoustic signaling.
1. Features
Acoustic signaling by means of piezoelectric transducer.
Optical signaling by means of LEDs.
Weatherproofed electronic circuit.
Tamper protection in 2 ways – cover removal and tearing enclosure from the wall.
High-impact polycarbonate enclosure, featuring a very high mechanical strength.
2. Description
1
Explanations for Fig. 1:
cover locking screw.
mounting holes.
auxiliary hole.
mounting holes for additional SPL-TO tamper sensor.
piezoelectric transducer.
2 SPL-5010 SATEL
opening for wires.
electronic board.
tamper element with mounting hole.
water drain holes (do not plug).
Terminals
+SO-
- input to trigger the optical signal. The signaling will be triggered after +12 V DC
voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to
terminal “-“.
+SA-
- input to trigger the acoustic signal. The signaling will be triggered after +12 V DC
voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to
terminal “-“.
TMP
- tamper output (NC). Connect one terminal to the control panel zone programmed
as tamper, and the other to the control panel common ground.
Additional tamper protection
Optionally, the SPL-TO optical tamper sensor can be installed in the siren. The sensor will
detect any attempt to tamper with the siren using mounting foam. It can be used to create an
independent tamper circuit or connected in series with the tamper circuit of the siren.
3. Installation and start-up
Power down the control panel before connecting the siren to it.
The siren must be installed on the wall, high above the floor, at a hard to access location, so
as to minimize the risk of tampering. Make sure that some free space is left above the siren
(at least 2.5 cm). Otherwise, it will be impossible to replace the cover.
1. Remove the cover locking screw.
2. Lift up the enclosure cover by approx. 80º and remove it (see Fig. 2).
SATEL SPL-5010 3
3. Place the enclosure base on the wall and mark the location of mounting holes. Remember
to allow for the mounting hole in the tamper element (see Fig. 1).
4. Drill the holes for wall plugs (screw anchors).
5. Run the wires through the opening in the enclosure base (see Fig. 1).
6. Using wall plugs (screw anchors) and screws, fasten the enclosure base to the wall (the
wall plugs and screws are included in the siren delivery set). Be careful when screwing
down the tamper element so as not to break the narrowings.
7. Connect the siren terminals with wires to the control panel terminals.
Note: Some alarm control panels may require that a resistor R (approx. 1 kΩ) be connected
between the +SA- terminals in the siren (see Fig. 3). Otherwise, the siren will produce
a buzzing sound when inactive.
8. Replace the siren cover, close the cover and then lock it with the screw.
9. Power on the control panel.
10.Test the siren for correct functioning. In order to test the siren you can use the output test
function, which is available in some control panels, or you can trigger an alarm for testing
purposes.
4. Specifications
Supply voltage ................................................................................................... 12 V DC ±15%
Maximum current consumption:
optical signaling....................................................................................34 mA
acoustic signaling ...............................................................................200 mA
Sound pressure level (at 1 m distance) .................................................................up to 120 dB
Environmental class according to EN50130-5 ........................................................................ III
Operating temperature range..................................................................................-35...+55 °C
Dimensions ......................................................................................................298x197x72 mm
Weight............................................................................................................................... 670 g
The declaration of conformity may be consulted at www.satel.eu/ce
4 SPL-5010 SATEL
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.eu
Table of contents
Other Satel Security System manuals
Satel
Satel ABAX 2 User manual
Satel
Satel MICRA User manual
Satel
Satel SD-3001 User manual
Satel
Satel SP-4002 User manual
Satel
Satel Micra MPB-300 User manual
Satel
Satel Micra MSP-300 User manual
Satel
Satel SD-3001 User manual
Satel
Satel ABAX 2 User manual
Satel
Satel ASP-100-R User manual
Satel
Satel SP-4002 User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual