Satel SP-4003 R User manual

OPTICAL-ACOUSTIC

OUTDOOR SIREN

SP-4003

sp4003_en 05/10

The SP-4003 optical-acoustic outdoor siren comes in three versions differing by the color of

optical signaling (red in SP-4003 R, blue in SP-4003 BL and orange in SP-4003 O).

1. Features

•Acoustic signaling by means of piezoelectric transducer.

•Optical signaling by means of two sets of LEDs.

•Three selectable tones for acoustic signaling.

•Weatherproofed electronic circuit.

•Tamper protection in 2 ways – cover opening or tearing housing from the wall.

•Inner cover of galvanized metal sheet.

•Housing made of PC LEXAN high-impact polycarbonate, featuring a very high mechanical

strength.

Explanations for Figure:

1 - housing cover.

2 - inner cover of galvanized

metal sheet.

3 - housing base.

4 - piezoelectric transducer.

5 - tamper contact (NC).

6 - electronics board.

7 - housing cover locking

screws.

Fig. 1. View of the siren.

2 SP-4003 SATEL

2. Description of electronics board

Fig. 2. View of the electronics board.

Explanations for Fig. 2:

1 - wires to LED sets.

2 - terminals:

+SO- - optical signaling control.

+SA- - acoustic signaling control.

TMP and TMP - tamper circuit.

SENS. and TMP - siren tamper contact.

3 - pins for tone selection.

4 - description of setting jumpers for respective acoustic signals.

Fig. 3. Selection of acoustic signal type: A – tone 1; B – tone 2; C – tone 3

(- pins shorted; - pins open).

5 - wires to piezoelectric transducer.

SATEL SP-4003 3

3. Installation

In order to take off the cover, remove the two locking screws and lift it by an angle of approx.

60º. Install the siren on flat surface, in a hard-to-reach place, so as to minimize the risk of

tampering.

Note: Leave a distance of at least 2.5 cm between the upper edge of the siren housing and

the ceiling or another object located above the siren. Otherwise, replacement of the

cover may be impossible.

The siren should be secured to the mounting surface by means of screws and screw

anchors. Be careful when screwing down the tamper element to which the tamper contact is

fastened, so as not to break the narrowings.

4. Connection

All electric connections may only be made with power supply disconnected.

The SP-4003 siren can work in conjunction with any device at the output(s) of which +12V

DC voltage will appear in emergency. The signal is triggered after +12 V voltage is applied to

the corresponding terminals of the siren (SA for acoustic signaling, SO for optical signaling).

Make sure that the output current rating of the signaling control outputs is sufficient and will

guarantee correct operation of the device.

Fig. 4. Method of connecting the SP-4003 siren to control panel. Output OUT1 triggers optical

signaling and output OUT2 – acoustic signaling (the high-current outputs with normal polarity

– activation means that +12 V voltage is supplied). Zone Z1 should be programmed as 24 h

tamper.

4 SP-4003 SATEL

5. Specifications

Power supply ..................................................................................................... 12 V DC ±15%

Maximum current consumption:

optical signaling ........................................................................................250 mA

acoustic signaling......................................................................................270 mA

optical and acoustic signaling ...................................................................520 mA

Sound pressure level (at 1 m distance)..................................................................up to 120 dB

Environmental class according to EN50130-5 ........................................................................III

Operating temperature range..................................................................................-35...+55 °C

Maximum humidity ..........................................................................................................93±3%

Housing dimensions.................................................................................... 148 x 254 x 64 mm

Weight...............................................................................................................................894 g

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

[email protected]

www.satel.eu

The latest EC declaration of conformity and product approval certificates are

available for downloading on website www.satel.eu

This manual suits for next models

Table of contents

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual