Royal Sovereign RSL-2701 User manual

Table Top Laminator

OWNER'S MANUAL

Read all instructions carefully before use.

For any Customer Support needs please choose the

Customer Support tab on www.royalsovereign.com

Royal Sovereign International Inc.

www.royalsovereign.com

TABLE OF CONTENTS

TOPIC PAGE

1. Introduction ....................................................................................................... 3

2. Package Contents .............................................................................................. 3

3. Safety Precautions.............................................................................................. 4

4. Parts.................................................................................................................... 5

5. Features Guide ................................................................................................... 6

6. Operation Instructions ......................................................................................... 9

7. Film Loading and Threading ............................................................................. 10

8. Maintenance .................................................................................................... 12

9. Trouble Shooting Guide .................................................................................... 13

10.Specification .................................................................................................... 14

11.Warranty ........................................................................................................... 15

Table Top Laminator

1. INTRODUCTION

2. PACKAGE CONTENTS

380-Series

Preloaded Roll Films

(380mm×75mic×30m)

(14in×3mil×98.4ft）

2701-Series

Preloaded Roll Films

(635mm×75mic×30m)

(25in×3mil×98.4ft）

Owner's Manual

Thank you for purchasing RS Table Top Laminator. It has been designed and manufactured

to provide years of continuous service. For high quality lamination, please read this

instruction manual thoroughly. This manual will provide you with complete operating and

maintenance information.

3. SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in

serious injury. Please read the instructions carefully and keep for future

1. Only a licensed electrician should install wiring and outlet for the laminator.

2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.

3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points

that can trap body parts or clothing and cause serious injury.

4. Keep flammable and wet objects away from the machine.

5. Place machine on a level surface.

6. Avoid excessive sunlight, humidity and extreme temperatures.

7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/

or repairing.

8. Keep out of reach of children.

9. Only Royal Sovereign authorized maintenance and service technicians should make

repairs.

10. Do not attempt to laminate items that exceed total recommended material thickness

for the unit

11. When cleaning the machine, don't use flammable sprays or materials.

12. Do not touch the rollers when they are hot or place foreign objects inside the machine.

13. Do not cover the surface of the machine until the machine has completely cooled.

*14.You can laminate by single film when the switch in the left cover is “O”.

(Insure the machine drastically cold, press the button in the left cover be “ O ”,then you

can laminate by single side. It is a damage for the paper to laminate by single side while

the rollers up and low are heating all together.)

4. PARTS

1.Upper Film 2.Lower Film 3.Idle Bar

4.Hot Rollers 5.Feed Table 6.Paper Guide

7.Control Panel 8.Tension Knob 9.Power Switch

*10.Single/Double Laminating Switch “O” (on) “I” (off).

* For Single Laminator.

Table Top Laminator

5. FEATURES GUIDE-1

Reverse the rollers to undo jams

and correct misfed documents

Run and stop the machine

Reduce roller speed

(1~10 speed settings)

Increase roller speed

(1~10 speed settings)

Film Application Thickness

125mic

* (100~125mic)

50~100mic

* (50~75mic)

25~38mic

* (25~38mic)

Figure 1

125mic(100~125mic)

50~100mic(50~75mic)

25~38mic(25~38mic)

RUN/STOP

REVERSE

DOWN

* For Single Laminator.

25-38 mic

50-100 mic

125 mic

210-230 F

230-270 F

270-310 F

5. FEATURES GUIDE-2

Reverse the rollers to undo jams

and correct misfed documents

Run and stop the machine

Reduce roller speed

(1~10 speed settings)

Increase roller speed

(1~10 speed settings)

Film Application Temperature

210 ~230 F

230 ~270 F

270 ~310 F

Figure 1

210~230 F

230 ~270 F

270 ~310 F

Table Top Laminator

25-38 mic

50-100 mic

125 mic

210-230 F

230-270 F

270-310 F

RUN/STOP

REVERSE

DOWN

Power Switch (1) - Located on the rear of

the machine. “I” (on) “0” (off). (Fig. 2)

Cross Cutter (2) - Used to cut off the

laminated web. (Fig. 2)

Feed Guide (3) -The feed guide permits

alignment of the item(s) to be laminated. To

position the adjustable guide, loosen the knob,

slide it to the desired position and tighten the

knob to secure the feed guide in place. (Fig. 3)

Safety Cover (4) - It prevents entanglement

NOTE: If the safety cover is opened, the power

to the motor will turn off.

Film Shaft and Locking

Core Adapter (5) -

The film shaft holds the film supply on the

machine. The locking core holds and locks the

film on the shaft to prevent shifting. (Fig. 4)

Film Tension Adjustment (6) - Allows the

operator to increase or decrease film web

tension. To increase the tension turn the knob

clockwise and to decrease tension turn the

knob counterclockwise. (Fig. 5)

Figure 2

Figure 3

Figure 4

Figure 5

1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)

2. Choose appropriate laminating thickness and speed. (Fig. 1)

3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).

4. Position the item to be laminated on the feed table.

5. Press the RUN button. The rollers will begin to turn, wait for heat line to disappear,

feed the item into the machine.

6. Insure the machine drastically cold, press the button in the left cover be “ O ”,then you

can laminate by upper roller for single laminating.(It is a damage for the paper to

laminate by single side while the rollers up and low are heating all together.)

7. The first paper is bad while OPP film laminating, please use a test paper first and then

the second paper must keep the distance less than 15mm form the front one.

8. Stop the laminator when all of the items have completely exited the rear of the

machine.

9. Please loose the film tension as loosed as possible.

10.If there the temperature is high while laminating by some films with thin paper on the

middle temperature level that you can use the low temperature level.

Repeat the above steps until all of your lamination is completed. When lamination is

completed the machine is not in use for an extended period of time turn the power off.

NOTE: Stand by mode and auto power off mode

- Stand by mode: If no activity is made within 30 minutes after each use the

machine will automatically switch into stand by mode. (In stand-by mode the

temperature will decrease to 80~90℃ and the three film thickness setting

indicators will blink).

- Auto power off mode: If the machine is in stand by mode and no activity is

made for 60 minutes the machine will automatically power off.

- If any activity is made while in stand by or auto power off mode the machine

will return to it’s previous stage.

6. OPERATION INSTRUCTIONS

Table Top Laminator

Figure 7

Figure 8

7. FILM LOADING & THREADING

Figure 6

1. Slightly slide the shaft to the right and pull it out

from the machine. (Fig. 7)

2. Take both lock core adapters off from the shaft.

Other manuals for RSL-2701

This manual suits for next models

Table of contents

Other Royal Sovereign Laminator manuals

Royal Sovereign

Royal Sovereign EL-9DF User manual

Royal Sovereign

Royal Sovereign ES-1310 User manual

Royal Sovereign

Royal Sovereign RPA-5954R User manual

Royal Sovereign

Royal Sovereign 1050 User manual

Royal Sovereign

Royal Sovereign ES-410 User manual

Royal Sovereign

Royal Sovereign RSC-5500H User manual

Royal Sovereign

Royal Sovereign NPH-1200N User manual

Royal Sovereign

Royal Sovereign RSL2701S User manual

Royal Sovereign

Royal Sovereign ES-1300C User manual

Royal Sovereign

Royal Sovereign RSL-382CR User manual

Royal Sovereign

Royal Sovereign NB-1900N User manual

Royal Sovereign

Royal Sovereign RSH-1151 User manual

Royal Sovereign

Royal Sovereign APL-330U User manual

Royal Sovereign

Royal Sovereign RSC-820CL User manual

Royal Sovereign

Royal Sovereign ES-1315 User manual

Royal Sovereign

Royal Sovereign RSC-1650C User manual

Royal Sovereign

Royal Sovereign APL-330U User manual

Royal Sovereign

Royal Sovereign RSH-380SL User manual

Royal Sovereign

Royal Sovereign RSH-380 User manual

Royal Sovereign

Royal Sovereign RSC-5500H User manual

Royal Sovereign

Royal Sovereign RSC-1400L User manual

Royal Sovereign

Royal Sovereign RSL2701S User manual

Royal Sovereign

Royal Sovereign IL-926W User manual

Royal Sovereign

Royal Sovereign NPH-1200N User manual

Popular Laminator manuals by other brands

Renz

Renz HT 330 L Operation manual

Gfp

Gfp 44TH Service manual

Lapis

Lapis Lamina006 user manual

Hama

Hama L44B instruction manual

PAVO

PAVO FLORIDA manual

M-Triangel

M-Triangel MT-102 Operating instruction

Akiles

Akiles PROLAM 230 instruction manual

D&K

D&K Masterpiece 550 owner's manual

Falcon

Falcon F-40 Operator's manual

LEITZ

LEITZ EasyLaminator A4 operating instructions

LEITZ

LEITZ coldLAM CS9 operating instructions

kala

kala Starter 1080 user manual

Fellowes

Fellowes Venus A3 Instructions before use

Qomolangma

Qomolangma FMJ-1400-WA-PLUS user manual

Opus

Opus Coverator 330 user guide

ALDI

ALDI OL 250-L user manual

Phoenix

Phoenix 2700-DH operating manual

acropaq

acropaq AL-3400 instructions