Royal Sovereign NPH-1200N User manual

OWNER'S

MANUAL

LAMINATOR Model No. NPH-1200N/900N

Read all instructions carefully before use.

MAJOR PARTS 3

CHARACTERISTICS OF NPH SERIES 3

SAFETY PRECAUTIONS 4

CONTROL PANEL INSTRUCTIONS 5

HOT LAMINATING PROCEDURE 8

COLD LAMINATING PROCEDURE 8

COLOR FOIL LAMINATING PROCEDURE 9

POUCH BOARD LAMINATING PROCEDURE 9

MAINTENANCE 10

TROUBLESHOOTING 10

SPECIFICATIONS 11

POUCH FILM SETTINGS 11

NPH-1200N/900N

TABLE OF CONTENTS

TOPIC PAGE

NPH-1200N/900N

MAJOR PARTS

CHARACTERISTICS OF NPH-SERIES

Cover Roller Screw Cover Roller Power Cord

Cover

Front Opening Control Panel LCD Panel

1. The NPH Series has been designed and manufactured to provide

Hot and Cold lamination for school, home and office needs.

2. Automatic cool down function- If the power is turned off or a power failure occurs the

rollers will continue to turn until they are cooled down.

3. Automatic overheating protection- If a temperature sensor were to fail the heating

elements will not heat up.

4. Digital control of speed, temperature and mil thickness with LCD display help ensure

professional results.

5. Laminates color foil.

6. Laminates over 2.5 feet per minute.

NPH-1200N/900N

SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result

in serious injury. Keep this information for future reference.

1. To prevent the possibility of fire or injury, do not allow articles of

clothing (neckties, scarves, or paperclips etc.) inside the machine.

2. Do not attempt to laminate items that exceed total recommended

material thickness.

3. To prevent the possibility of electric shock, do not immerse the

laminator in water or permit liquids inside the machine.

4. Do not operate machine for any other purpose other than its

intended use.

5. This machine is for indoor use only.

6. Do not operate the machine if the outlet or power cord is

damaged. Contact a qualified electrician.

NPH-1200N/900N

CONTROL PANEL INSTRUCTIONS

Appropriate speed and temperature may be set, using the LCD controller. The LCD

panel was designed for convenience, by incorporating the ability to program your

settings into "Memory".

1. CONTROL PANEL SETTINGS

LCD DISPLAY

CONTROL PANEL

NPH-1200N/900N

2. LCD WINDOW

Mic

125Mic

Foi l

250

Mic

175

Mic

100Mic

SPEED TEMPERATURE

1. Pouch Thickness

* 6 Pouch

Thickness Options

75 mic =3 mil, 100 mic =4 mil, 125 mic =5 mil

175 mic =7 mil, 250 mic =10 mil

2. SPEED

Seven speed options (1-7)

3. TEMPERATURE

Displays current temperature

4. Displayed when desired temperature

is met.

5. This indicates that the current temperature

is either higher or lower than the preset

temperature.Wait until the indicator stops

blinking.

6. Indicates what direction the rollers

are moving in (FWD/REV).

7. Displayed when the machine is in the cold

temperature mode.

Mic-

3mil

125

Mic-

5mil

Foil

250

Mic-

10mil

175

Mic-

7mil

100

Mic-

4mil

TEMPERATURE

NPH-1200N/900N

3. CONTROL PANEL FUNCTIONS

T-Check

HOT/COLD

MEMORY

TEMPERATURE

SPEED

PROGRAM

POWERREVERSE

: Press this to check the current

temperature

: Press this to choose Hot

or Cold function

: Press this to set current temperature

in memory (up to 6 memory settings)

or to recall preset temperature settings.

: Increase or Decrease Temperature

: Increase or Decrease Speed

: To scroll through preset temperature

settings

: Reverse Function

: Power ON/OFF

TEMPERATURE

SPEED

PROGRAM

1. Place and use the laminator on a sturdy, flat work surface.

2. Plug in the laminator after verifying the correct outlet voltage.

3. Press the power button.

4. Make sure the machine is in the hot lamination mode by pressing the

HOT/COLD button.

5. Select the correct pouch thickness by pressing the program buttons up or down.

6. Set the temperature and speed according to the pouch thickness.

Please refer to the SPECIFICATIONS section for recommended settings.

7. The symbol will stop blinking and a symbol will appear when your

desired temperature is met. The machine is now ready for lamination.

8. Place the item to be laminated into the laminating pouch.

9. Insert the pouch (sealed side first) into the front opening of the machine.

10. The laminated item will exit out the rear of the machine when completed.

11. If you laminate several items continuously the may disappear, please wait

until it is displayed again before continuing lamination.

NOTE: Your laminated item will be hot and can easily bend. To keep your

laminated item flat, place on a flat surface and allow it to cool.

NPH-1200N/900N

HOT LAMINATING PROCEDURE

COLD LAMINATING PROCEDURE

1. Make sure the machine is in the cold lamination mode by pressing the

HOT/COLD button. You will see the displayed when the machine

is in the cold temperature mode.

2. The symbol will stop blinking and a symbol will appear when the cold

temperature is met. The machine is now ready for lamination.

3. Place the document to be laminated on the adhesive side of the cold film with the

document face down.

4. Insert the document to be laminated into the front opening of the machine.

5. Remove paper liner from the cold film slowly while the document is being inserted

into the machine.

NOTE: When switching the machine from the hot to cold mode, please

wait until the rollers cool down. It will take approximately 6 minutes.

The symbol will appear and you will hear 3 beeps.

1. Make sure that the machine is in the Foil lamination mode by pressing the

PROGRAM buttons up/down until it is in the foil mode.

2. Set the temperature and speed according to the pouch thickness (FOIL).

Please refer to the SPECIFICATIONS section for recommended settings.

3. The symbol will stop blinking and a symbol will appear when the correct

temperature is met. The machine is now ready for lamination.

4. Place the document into the pouch board.

5. Insert the pouch board (sealed side first) into the front opening of the laminator.

6. The finished item will exit out the rear of the machine when completed.

NPH-1200N/900N

COLOR FOIL LAMINATING PROCEDURE

POUCH BOARD LAMINATING PROCEDURE

IMPORTANT: Carrier is required for Foil Lamination

1. Make sure that the machine is in the Foil lamination mode by pressing the

PROGRAM buttons up/down until it is in the foil mode.

2. Set the temperature and speed according to the pouch thickness (FOIL).

Please refer to the SPECIFICATIONS section for recommended settings.

3. The symbol will stop blinking and a symbol will appear when the correct

temperature is met. The machine is now ready for lamination.

4. Position the color foil on the document with the color side facing up. When you are

applying the foil to small areas or using different colors, use the tape that’s included

to hold the foil in place.

5. Place the document into the paper carrier.

6. Insert the carrier into the front opening of the machine.

7. The carrier will exit out the rear of the machine when completed.

NOTE: Your laminated item will be hot and can easily bend. To keep your laminated

item flat, place on a flat surface and allow it to cool.

NPH-1200N/900N

MAINTENANCE

TROUBLESHOOTING

When adhesives from the film build up on the rollers the quality of lamination

will decrease and jamming may occur. Please clean the rollers regularly.

1. Turn on the laminator and set the temperature at 100°C(212°F) and set the mil

thickness at 100 mic(4mil).

2. Insert a sheet of clean thick paper (about 0.5 mm or 1/50” thick) into the front

opening of the machine 2-3 times to remove excess adhesive from the rollers.

3. To thoroughly clean the rollers make sure the machine is in the COLD mode and the

rollers are completely cool.

4. Unscrew the 2 screws on the cover using a screwdriver. Once the screws are off,

remove the top cover.

5. Use a cleaning solvent such as Laminex Poly-Off or something equivalent on a lint

free cloth to clean residue on the rollers. (Do not use alcohol or petroleum based

cleaning solvents or abrasives.)

6. Place the cover back on and screw in tightly.

7. Use and store this unit in a dry area, damp areas may damage the machine.

Problem Possible Cause Possible Solution

Motor doesn’t work

- Power cord may not be

plugged in.

- Power switch is off

- If laminating heat sealed

pouches, the machine may

be set in the COLD mode

- The temperature may be

set too low.

- The speed is set too high

- Check and plug in the

power cord.

- Check and turn on the

power.

- Make sure the machine is

in the HOT mode

- Check the temperature is

set according to pouch

thickness.

- Adjust to a lower speed.

Pouches are not

laminating correctly

Other manuals for NPH-1200N

This manual suits for next models

Table of contents

Other Royal Sovereign Laminator manuals

Royal Sovereign

Royal Sovereign NPH-1200N User manual

Royal Sovereign

Royal Sovereign PL - 922 User manual

Royal Sovereign

Royal Sovereign RSC-1401C Series User manual

Royal Sovereign

Royal Sovereign RSC-1400C User manual

Royal Sovereign

Royal Sovereign RSH-1151 User manual

Royal Sovereign

Royal Sovereign RSL-2701 User manual

Royal Sovereign

Royal Sovereign ES-1315 User manual

Royal Sovereign

Royal Sovereign CS-900 User manual

Royal Sovereign

Royal Sovereign RHD-2201 User manual

Royal Sovereign

Royal Sovereign ES-900C User manual

Royal Sovereign

Royal Sovereign RSC-5500H User manual

Royal Sovereign

Royal Sovereign APL-230 User manual

Royal Sovereign

Royal Sovereign RSH-380 User manual

Royal Sovereign

Royal Sovereign CL-1223 User manual

Royal Sovereign

Royal Sovereign RFCI-1826 User manual

Royal Sovereign

Royal Sovereign RSC-5500H User manual

Royal Sovereign

Royal Sovereign RSL-2702 User manual

Royal Sovereign

Royal Sovereign PL-1310 User manual

Royal Sovereign

Royal Sovereign NR-901 User manual

Royal Sovereign

Royal Sovereign NB-1900N User manual

Royal Sovereign

Royal Sovereign RSC-1650C User manual

Royal Sovereign

Royal Sovereign RSC-820CL User manual

Royal Sovereign

Royal Sovereign RSL-2702 User manual

Royal Sovereign

Royal Sovereign IL-926W User manual

Popular Laminator manuals by other brands

Renz

Renz HT 330 L Operation manual

Gfp

Gfp 44TH Service manual

Lapis

Lapis Lamina006 user manual

Hama

Hama L44B instruction manual

PAVO

PAVO FLORIDA manual

M-Triangel

M-Triangel MT-102 Operating instruction

Akiles

Akiles PROLAM 230 instruction manual

D&K

D&K Masterpiece 550 owner's manual

Falcon

Falcon F-40 Operator's manual

LEITZ

LEITZ EasyLaminator A4 operating instructions

LEITZ

LEITZ coldLAM CS9 operating instructions

kala

kala Starter 1080 user manual

Fellowes

Fellowes Venus A3 Instructions before use

Qomolangma

Qomolangma FMJ-1400-WA-PLUS user manual

Opus

Opus Coverator 330 user guide

ALDI

ALDI OL 250-L user manual

Phoenix

Phoenix 2700-DH operating manual

acropaq

acropaq AL-3400 instructions