Rize MULTI-FLEX User manual

OWNER’S MANUAL

Wireless Adjustable Bed

Model Number: RI-ABT-A18-WWM-U-L-S-FM

Serial Number: ___ __________ ______

(Pla e your serial number here for ready referen e)

The

“MULTI-FLEX”

This produ t and all our bedding produ ts are overed by one or more of the following issued and pending U.S. patents in luding

Nos. 7448100, D657157, D663542, D657158, D657156, 8209801, 8209800, D663544, D663543 and other patents pending.

“With Bluetooth Single-Speaker

Sound System”

Wireless Adjustable Bed

Safety Pre autions.......................................................................1

Parts List......................................................................................3

Installation Guide........................................................................4

Wireless Hand Control Operation Guide .................................6

A tivating Bluetooth Sound System ......................................10

Troubleshooting ........................................................................11

Warranty & Registration ............................................................13

Model Number:RI-ABT-A18-WWM-U-L-S-FM

Table o Contents

The “MULTI-FLEX”

Sa ety Precautions

ATTENTION!

IMPORTANT SAFETY INSTRUCTIONS.

PLEASE READ THESE INSTRUCTIONS

THOROUGHLY BEFORE USING THIS

PRODUCT.

ELECTRICAL SAFETY

Always unplug this adjustable bed frame from the

ele tri al outlet before any leaning or maintenan e

of the bed frame. To safely dis onne t, make sure all

ontrols are in the off position, then remove the

plug from the outlet.

Keep ord away from heated surfa es. Keep air

openings free of lint, hair and the like - never operate

when air openings are blo ked. Never drop or insert

any obje t into any opening. Use only indoors.

Cease use of this bed frame and onta t a qualified

servi e enter for repair if: (1) it has a damaged ord

or plug, (2) it is not working properly, (3) it has been

dropped or damaged, or (4) it has been dropped

into water.

GROUNDING SAFETY

To redu e the risk of ele tri sho k, ele tri al fire, or faulty

operation of this produ t, your Adjustable Bed features a

polarized plug meant to be used only with a grounded

ele tri al outlet. If this plug does not fit into your outlet,

onta t a qualified ele tri ian to install a properly

grounded outlet. Failure to use a properly grounded

outlet for this produ t will ompromise this important

grounding safety feature. The use of adapters is not

re ommended unless the outlet is he ked by a

qualified ele tri ian to ensure the proper grounding of

the adapter. Please note: Unauthorized modifi ations

to this produ t ould void the ele tri al portion of

your warranty.

FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED

SHOULD BE PLUGGED INTO A SURGE PROTECTOR

(not supplied with this Adjustable Bed).

WARRANTY WARNING!

This bed is spe ifi ally designed to require no

maintenan e by you, the user. Any opening or tamper-

ing with the ontrol box, motors or hand ontrols (with

the ex eption of the battery ompartment if equipped)

will result in a void of the warranty. Only those

authorized may ondu t repairs or part

repla ement on your adjustable bed.

IN-HOME USE ONLY

This Adjustable Bed

is designed ex lusively for in-home use.

HOSPITAL DISCLAIMER: It is NOT designed for hospital use

and is NOT designed to meet hospital standards. Do not

use this bed with TENT TYPE oxygen therapy equipment or

use near explosive gases.

IMPORTANT SAFETY FEATURES

Weight failsafe feature: In the ase that an overload of

weight is pla ed on the head or foot me hanism, the

ontrol unit will automati ally stop all fun tions. The

ontrol unit will automati ally resume all fun tions

30 se onds after ex ess weight is removed.

Lo king aster feature: This Adjustable Bed may be

equipped with spe ial lo king asters. For your safety,

these asters will prevent bed movement when all

asters are in the lo ked position. To lo k asters, push

down the safety lat h on the aster. To resume produ t

mobility, lift the safety lat h up.

Please note: I your Adjustable Bed is positioned on a

hard loor sur ace such as hardwood or tile, it is strongly

recommended that rubber caster cups or carpet squares

are placed under the casters in addition to locking them

in place. Casters will not roll when locked, but may slide

on an uncarpeted sur ace.

Wireless Adjustable Bed

The “MULTI-FLEX”

Sa ety Precautions

SAVE THESE

INSTRUCTIONS!

Proper operation of your

Adjustable Bed®is necessary to

ensure the long life and durability you

expect from a high-quality product.

The manufacturer has tested and

inspected this product prior to shipment.

CONSUMERS WITH PACEMAKERS

It is possible that the (optional) vibrating feature of this

bed may be interpreted falsely by some pa emakers as

movement and/or exer ise. This is ommon with any

produ t that produ es a vibrating motion, and may or

may not affe t your pa emaker. Please onsult your

physi ian with any on erns.

RADIO FREQUENCY IS 433.92 MHZ.

FCC omplian e devi e omplies with part

15 of the FCC Rules.

Operation is subje t to the following two onditions:

(1) This devi e may not ause harmful interferen e, and

(2) this devi e must a ept any interferen e re eived,

in luding interferen e that may ause undesired

operation.

Any hange to the antenna or the devi e ould result in

the devi e ex eeding the RF exposure requirements and

void user’s right to operate the devi e.

The input transformer voltage is AC120V 60HZ; the

output voltage is DC24V 3A. In the ase of a short- ir uit,

a fuse on the transformer will blow to prote t the

ele tri al equipment of the devi e (Fuse: 1A~1.5A.).

Should this o ur, you should seek professional assistan e

to fix the problem, and all Customer Care at:

1-877-826-8757

PRODUCT RATINGS

Lift Motor Restri tions: The lift motors in this bed are

NOT designed to operate ontinuously for more than

three (3) minutes over a thirty (30) minute time period,

or approximately 10% duty y le. To ensure reliable

fun tionality and full life of this produ t, do not attempt

to ex eed these limits.

NOTE: Attempting to circumvent or exceed this rating will

shorten the li e expectancy o the product and may void

the warranty.

Weight Restri tions: The re ommended

weight limits on our adjustable beds are:

Twin/TXL/Split QN/Split CA King: 575 Pounds,

Full/FXL: 600 Pounds, Queen: 650 Pounds.

The stru ture of the bed will support the re ommended

weight when distributed evenly a ross the bed.

The hea an foot sections are not esigne to

in ivi ually support or lift this amount of weight.

For optimal performan e, entering and exiting the

adjustable bed with the bed in the flat or level

position is re ommended.

NOTE: Exceeding the recommended weight restrictions could

damage your adjustable bed and void your warranty.

SMALL CHILDREN AND

PETS WARNING

Immediately dispose of all pa king materials as it an

pose a smother risk to small hildren and pets. Injury

ould o ur also if hildren or pets are permitted to play

on or under the bed. Do not allow hildren to operate

this bed without adult supervision.

Wireless Adjustable Bed

The “MULTI-FLEX”

NOTE: Before discarding any packing

materials, check the adjustable bed

frame carton and verify all items in

the parts list are included:

A. Remote Control (1)

B. Mattress Retainer Bra ket (1)

C. Bed Leg (2)

D. Inner Headboard Bra ket (2)

E. Outer Headboard Bra ket (2)

F. Retainer Bolt (4)

G. Headboard Bra ket Bolt (6)

H. 1/4 In h Washer (2)

I. 5/16 In h Washer (12)

J. 5/16 In h Nut (6)

K. Allen Key Wren h (1)

L. Wren h (1)

M. Lounger Bed Leg (2)

N. Knob Bolt (2)

O. Spring Washer (2)

Parts List

(1)

(2)

(4)

(6)

(2)

(12)

(6)

(1)

(2)

Wireless Adjustable Bed

The “MULTI-FLEX”

Installation Guide

STEP 1.

For safety reasons, the following should be performed by 2 people.

Carefully lift the bed frame unit out of the shipping arton with the

top side fa ing downward.

STEP 2. Assembling Be Legs

For this step, you will need: 4 bed legs (Cand M), Knob bolts (N),

and spring washers (O), whi h an be found in the A essories box.

First turn the two (C) bed legs in a lo kwise dire tion into the holes

in the frame as shown above. Next thread ea h Lounger bed leg (M)

into the C- hannel frame. Make sure the leg opening is fa ing inside

the frame. Then, insert a Knob bolt (N) fitted with a spring washer

(O) into the predrilled hole in the C- hannel frame and through the

lounger bed leg. Tighten the Knob bolt in pla e. Repeat with the

remaining Lounger bed leg.

STEP 3.

Remove and extend the power ord from the frame.

STEP 4.

Take plasti wrapping off the base frame.

STEP 5.

Carefully rotate the base frame over so the top side is fa ing upward.

Be areful not to rest the frame on its side. The weight may damage

the legs.

STEP 6.

Plug the power ord into a grounded ele tri al outlet.

STEP 7.

Install batteries in remote.

If the remote is a wired remote, no batteries are needed.

Try all fun tions on the hand ontrol to

ensure all features are operational.

If the bed does not work, refer to Troubleshooting on p.1 .

STEP 8.

Return bed to flat or level position.

STEP 9. Assembling

The Mattress Retainer Bracket

Fasten the mattress retainer bra ket (B) to the front of the bed frame

using the retainer bolts (F) and 1/4 in h Retainer washers (H), as

shown in the diagram below.

DO NOT OVERTIGHTEN THE BED LEGS.

NOTE:

Bed may be equipped with spe ial lo king

asters. To prevent movement of this produ t, all four

asters should be in the lo ked position. It is re om-

mended that rubber aster ups or arpet squares (not

in luded) are pla ed under asters in addition to lo king

them inpla e. Casters will not roll when lo ked, but may

slide on an un arpeted surfa e.

NOTE:For optimal safety, a surge prote tor should be

used (not supplied with this Adjustable Bed).

NOTE :

Use ONLY the allen wren h to fasten the retainer

bolts. DO NOT use a power s rewdriver as it may over tighten the

bolts. Mattress retainer hardware must NOT be over tightened.

If the adjustable frame is to be set up without a headboard,

simply install a mattress on the frame.Installation is now complete.

If a headboard is to be installed, proceed to step 10 on next page.

Important!

MAKE SURE POWER CORDS DO NOT OBSTRUCT

ANY ADJUSTABLE BED MECHANISMS.

Wireless Adjustable Bed

The “MULTI-FLEX”

Installation Guide

STEP 10. Assemble the Hea boar Bracket

i. Use the remote to elevate the head of the bed so

the bed base frame is rea hable.

iv. When headboard bra kets are assembled, make sure there is a spa e of 1.5 (38.1 mm) to 2 in hes (50.8 mm)

between the edge of the bed base and the headboard bra kets.

v. Se urely fasten the headboard bolts (not in luded with your adjustable bed) to the end of the headboard bra ket assembly.

vi. Measure the distan e from the enter of one mounting hole in the headboard to the enter of the other.

vii. Measure the distan e from the enter of one mounting hole in the headboard bra ket assembly to the enter of the other.

viii. If you need to adjust the headboard bra kets, uns rew the bolts holding the outer headboard bra kets and move them

the ne essary distan e. Reinstall the bolts and se urely tighten.

STEP 11.

Pla e your mattress on the adjustable bed frame surfa e. Your adjustable bed and headboard installation is now omplete.

If the bed omes with a programming option, turn to the Wireless Hand Control Operation Guide to pro eed.

IMPORTANT NOTES:

Failure to follow the installation steps as they appear in this gui e

coul result in amage to your a justable be frame.

Make sure to position the bottom of the hea boar cross member no more than

3 inches (76.2 mm) between the hea boar an the top of the mattress.

ii. Slide the inner headboard bra ket (D) into the C- hannel

frame. (The bra ket opening and the C- hannel opening should

fa e ea h other to reate a box shape.) Insert a retainer bolt (G)

fitted with a 5/16 in h washer (I) into one of the predrilled holes

in the C- hannel frame and through the inner headboard

bra ket. Tighten in pla e with a 5/16 in h washer (I) and 5/16

in h nut (J). Repeat on the other side.

iii. Pla e the open side of the outer headboard bra ket (E) onto

the exposed square tube of the inner headboard bra ket (D) to

reate a tight fit between (D) and (E). Insert a retainer bolt (G)

fitted with a 5/16 in h washer (I) into the outer headboard

bra ket (E) and through the inner headboard bra ket (D). Hand

tighten using a 5/16 in h washer (I) and a 5/16 in h nut (J).

(Leave loose enough for adjusting.) Repeat on

the other side.

Wireless Adjustable Bed

The “MULTI-FLEX”

Wireless Hand

Remote Operation

FOR YOUR SAFETY, READ THE OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE

OPERATING THIS PRODUCT. ELECTRIC SHOCK MAY OCCUR IF ELECTRICAL COMPONENTS

ARE NOT INSTALLED OR OPERATED ACCORDING TO THESE GUIDELINES.

Hea an Foot Position A justments (A, B, C, D)

• Press & Realease button to raise or lower the head and foot se tions of your adjustable bed. The premium “Wall-Glide” feature

will automati ally syn hronize with all Head & Foot adjustments. NOTE:* “D” will allow the lowering of the foot se tion for a

“LOUNGE” position.

Incline (E)

• Press to raise the head se tion to an ideal position for wat hing TV, reading or laptop use.

Be “Flat” Button (F)

• Press down and hold for 2 se onds to return bed to the flat position.

Zero Gravity (G)

• This fun tion allows your legs to be lifted to a position slightly higher than the hest. This allows blood to flow

ba k to the heart, redu ing stress and fatigue.

LED Signature Light

A. Raises the Head of the Bed

B. Lowers the Head of the Bed

C. Raises the Foot of the Bed

D.Lowers the Foot of the Bed

F. Returns Head & Foot to FLAT

Position (hold 2 seconds)

I. Increases the Intensity

of Vibration (Head)

K. Increases the Intensity

of Vibration (Foot)

J. Decreases the Intensity

of Vibration (Head)

N. Turns on Massage

Wave 1,2 or 3

L. Decreases the Intensity

of Vibration (Foot)

G. Zero Gravity

H. Lounge

M. Full Body Massage

O. Stops Massage

E. Incline Watching TV/Reading

Wireless Adjustable Bed

The “MULTI-FLEX”

P. Under

Bed Light

Wireless Hand

Remote Operation

NOTE:This bed may show minor intermittent performance because of typical RF interference. This is normal in the operation of the bed, not a defect.

Lounge (H)

• Press & Release to lower your legs, Raise your head and relax in a lounge position.

Hea an Foot Massage A justments (I,J,K,L)

• Press & Release button to a tivate the massage feature on the head and foot of the bed (starting at intensity 4 of 8).

Gradually in rease or de rease intensity of massage vibration by pressing the appropriate button. The lowest setting on

ea h massage unit will turn off the respe tive vibration. The massage feature is programmed with an Auto Shut-Off Timer

that will automati ally turn off the massage after 15 minutes of ontinuous use.

Full Bo y Massage (M)

• Press to a tivate both the head and foot massages at the same time.

Wave Massage A justments (N)

• A tivates both units to wave mode massage. NOTE: You must stop the massage in order to a tivate another

massage setting su h as full body or another wave massage

Stop Button (O)

• Hold down for 2 se onds to stop massage..

Un er Be Light (P)

• Press the button to turn on or off the under bed light. (Button on ba k of Remote)

Remote Features

• The Wireless Adjustable Bed uses a RF (Radio Frequen y) hand ontrol system.

• The buttons are ba klit, when a button is pressed, to aid in the visibility of the remote in low light environments.

• It is not ne essary to fa e the re eiver to operate the remote ontrol. Remote signal is best transmitted within

9 feet (3 meters) of the re eiver.

Safety

• In the ase that an overload of weight is pla ed on the head or foot me hanism, the ontrol unit will automati ally stop all

fun tions. The ontrol unit will automati ally resume all fun tions 30 se onds after ex ess weight is removed.

• Massage motors will automati ally shut off after running ontinuously for 15 minutes. All massage fun tions will be

operational again after 5 minutes. Automati Shut Off will o ur after 15 minutes of ontinuous use.

• The input transformer voltage is AC120V 60HZ, the output voltage is DC24V 3A. In the ase of a short- ir uit, a fuse on the

transformer will blow to prote t the ele tri al equipment (Fuse: 1A~1.5A.). Should this o ur, you MUST seek professional

assistan e to repla e the fuse. Call Customer Care at: 1-877-826-8757

Notice: The hanges or modifi ations not expressly approved by the party responsible for omplian e ould void the user’s

authority to operate the equipment.

Important Note: To omply with the FCC RF exposure omplian e requirements, no hange to the antenna or the devi e

is permitted. Any hange to the antenna or the devi e ould result in the devi e ex eeding the RF exposure requirements and

void user’s authority to operate the devi e.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Continued

NOTE:I

f the massage motors are operating and the “FLAT” button (F) is presses, the massage motors will stop

operating during the lowering of the bed frame. after 30 seconds, the massage motors will resume operation.

Wireless Adjustable Bed

The “MULTI-FLEX”

Wireless Hand

Remote Programing

Wireless Hand Remote Programing

1. Insert batteries into the

Hand remote ontrol (2xAA batteries).

2. Make sure your adjustable bed is plugged into

a working grounded outlet or surge prote tor.

3. Hold down the learn button for 3 se onds.

4. The LED signature light will illuminate.

This means the RF frequen y ode setting

fun tion has been a tivated.

6. When the re eiver light flashes, the RF

frequen y ode learning pro ess is omplete.

Note: Programming by the user is only needed on repla ement remotes.

(1 Hand Control and 1 Bed)

(1 Hand Control and 2 Beds)

Figure 1:

Press the

"Learn Button"

to initiate the

RF learning

mo e.

Figure 2:

The re LED

will light up

when the

control box

is in the

learning

mo e.

5. Press any button

on the remote

ontrol

Figure 3:

Han hel

remote control

Figure 4:

A flashing re

LED in icates

the control

box has

receive

the remote

control figure

1. Follow steps 1 through 6 above for 1 hand ontrol and 1 bed.

2. Repeat the steps for the other bed using the same hand ontrol.

The “MULTI-FLEX”

Wireless Adjustable Bed

The “MULTI-FLEX”

This manual suits for next models

Table of contents

Other Rize Indoor Furnishing manuals

Popular Indoor Furnishing manuals by other brands

Homelegance

Homelegance California 1662PEK-1CK Assembly instruction

Osmond Ergonomics

Osmond Ergonomics FLO instructions

OVE

OVE ELOISE 42 installation manual

overstock

overstock MF286255 Assembly instructions

Sonoma

Sonoma 160-801 Assembly instructions

BOLERO

BOLERO Wicker Side Chair CF158 Care Instructions

Coaster

Coaster 4799N Assembly instructions

Stor-It-All

Stor-It-All WS39MP Assembly/installation instructions

Lexicon

Lexicon 194840161868 Assembly instruction

Next AMELIA NEW 462947 Assembly instructions

Furinno

Furinno 18089 Assembly instruction

Munchkin

Munchkin Push to Close MK0001 manual

impekk

impekk Manual II Assembly And Instructions

Elements

Elements Ember Nightstand CEB700NSE Assembly instructions

JWA

JWA CARY 68429 Assembly instruction

VIPACK

VIPACK AMORI AMKB9014 Assembly instructions

Anthro

Anthro GT03 Series Assembly instructions

Rowico

Rowico SANNA Assembly instructions