Rinnai Efficiency HD250i User manual

Rinnai New Zealand 1 HD250i Flueing Installation: 01-07

Rinnai New Zealand 1

RINNAI

HD250i Direct Flueing with Wall Terminal

Flueing Installation Instructions

This ue shall be installed in accordance with:

Manufacturer’s Installation Instructions

Local Gas Fitting Regulations

Municipal Building Codes

NZS:5261 Installation Code

Any other local relevant statutory regulation

This appliance and ue system must be installed, serviced and removed by an Authorised person.

•

Rinnai New Zealand 2 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Summary

Direct Flueing with Wall Terminal

For installations where the Rinnai Innity HD250i Internal is mounted directly on the inside of an

external wall.

The HD250i Direct Flue Kit (FFTL-10-200) can used to ue through walls 150-250mm thick (this

can not be extended).

Exhaust

Intake DIM Description DIM

(mm)

A Width 470

B Depth 220

C Height - Unit 600

D Height - Including Brackets 620

E Hot Water Outlet (from wall) 112 ~149

F Hot Water Outlet (from center) 61

G Cold Water Outlet (from wall) 94 ~135

H Cold Water Outlet (from center) 51

I Gas Connection (from wall) 56 ~96.5

J Gas Connection (from center) 110

KDistance between Flue Pipes 150

Positioning - Space Required

Inside Outside

Rinnai New Zealand 3 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Kit / Important

Direct Flueing - Kit Components

Flue Terminal Chamber Sleeve Condensate Proof Cover

Screw Kit (in actual kit, screw components are packaged in a clear plastic roll pack)

Important Installation Notes

The components of this ueing system CAN NOT BE CUT, use telescopic components to achieve the

required length

Ensure positioning of the ue terminal and ue installation comply with NZS:5261. The ue

products can reach temperatures above 200oC.

Flue must be supported and be independent of the appliance

Ensure the appliance can be removed without causing movement or displacement of the ue

Flue components are self-locking

The O-Rings in all the components are pre-greased, ensure they are not damaged when joining

When preparing the wall penetration, cover ue spigot to prevent debris from entering the

appliance

Before Installation

Wall hole diameter is Ø175mm or greater and is secure

That there is a 2o angled fall to the ue terminal

Length of sleeve tube has been checked, wall thickness can be 150 - 250mm thick

Distance to surroundings of the ue terminal as per NZS:5261

•

Screw (M4)

Tapping Screws (ø 3.8 x L32) Buttery Nuts (M5)

Trim Nut (M4)

Screw Plugs (#10)

Rinnai New Zealand 4 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Installation

Sealant Sleeve

Sealant

2ofall

Sleeve / Chamber Installation

Adjust sleeve length to thickness of wall allowing an additional 15mm (this is so it sits inside the

ue cowl) and secure sleeve to chamber with screw (B). Ensure you align sleeve and screw with

predrilled hole / slot.

Insert sleeve / chamber into wall and mark screw position where the sleeve will attach to the wall

Drill screw position and insert screw plugs

Fit sleeve plate with four screws ensuring spacer is positioned so there is a 2oangled fall

Apply plaster lling to gap between sleeve and wall and silicon sealant around the sleeve tube

•

Chamber

Buttery nuts

Sleeve

Spacer

Sleeve

Screw

Plug

Tapping

Screw

10-15mm

Sleeve

Rinnai New Zealand 5 HD250i Flueing Installation: 01-07

HD250i Direct Flueing - Installation

Flue Terminal Installation

Insert ue terminal into chamber so as the terminal is angled to fall

Fit terminal with condensate proof cover with trim nut and apply silicone sealant around ue

terminal

Within the condensate cover there is a wind buffer plate which can be congured to certain

positions if obstructions exist.

•

Twist to insert

Full thread screw

Condensate proof

cover

Trim nut Full thread screw

Left Obstruction Upper Obstruction

Wind Buffer Plate

Condensate Proof

Cover

Wind Buffer Plate

Condensate Proof

Cover

Right Obstruction

Condensate Proof

Cover

Wind Buffer Plate

Rinnai New Zealand 6 HD250i Flueing Installation: 01-07

Customer Contacts

For more information about buying, living and

servicing of Rinnai gas appliances call

0800 RINNAI (0800 746 624).

Rinnai New Zealand Limited

691 Mt Albert Road

PO Box 24068, Royal Oak, Auckland

Email: [email protected]

www.rinnai.co.nz

All Rinnai appliances meet or exceed the

safety standards required by New Zealand gas

and electrical regulations.

Rinnai is constantly improving its products

and as such specications are subject to

change or variation without notice.

RINNAI

HD250i Direct Flueing with Wall Terminal

PART NUMBER: 15246

Issue: A

Other manuals for Efficiency HD250i

Table of contents

Other Rinnai Heater manuals

Rinnai

Rinnai Energysaver EX38C User manual

Rinnai

Rinnai Cosypanel User manual

Rinnai

Rinnai RCE-229A Quick start guide

Rinnai

Rinnai RHFE-309FT Specification sheet

Rinnai

Rinnai rhfe-431ft User manual

Rinnai

Rinnai rhfe-556ftp User manual

Rinnai

Rinnai ES17 User manual

Rinnai

Rinnai ES38 RHFE-1004RFA User manual

Rinnai

Rinnai RHFE-557FT User manual

Rinnai

Rinnai RCE-606TRA II Quick start guide

Rinnai

Rinnai ENERGYSAVER RHFE-308FTR Operating instructions

Rinnai

Rinnai ODHRAD3MN Specification sheet

Rinnai

Rinnai Granada 252 User manual

Rinnai

Rinnai FC510 User manual

Rinnai

Rinnai RCE-329A User manual

Rinnai

Rinnai Demand Duo User manual

Rinnai

Rinnai FC824 User manual

Rinnai

Rinnai Avenger 25 User manual

Rinnai

Rinnai RHFE-551FT User manual

Rinnai

Rinnai INFINITY 16 Installation instructions

Rinnai

Rinnai Energysaver RHFE-1004FTR Operating instructions

Rinnai

Rinnai RCE-606A User manual

Rinnai

Rinnai RCE-592ACPA Installation and operating instructions

Rinnai

Rinnai RHFE-309FT Specification sheet

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide