Prorack K997W User manual
K997W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 1 x 1 x 2
x 2 x 2 x 1 x 1
x 2 x 2 x 2
Revision No: 1A 1
Fitting Kit K997W
MAX kgs (lbs)
W/P WHD
Jeep
Renegade Sport, 5dr SUV 15-+ AU 68 kgs (149 lbs) 68 kgs (149 lbs)
Renegade Sport, 5dr SUV 15-+ EU 68 kgs (149 lbs) 68 kgs (149 lbs)
Renegade Sport, 5dr SUV 16-+ NZ 68 kgs (149 lbs) 68 kgs (149 lbs)
2
Fitting Kit K997W
X
A B C 1 2 3
Renegade Sport, 5dr SUV 15-+ (AU) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
Renegade Sport, 5dr SUV 15-+ (EU) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
Renegade Sport, 5dr SUV 16-+ (NZ) 275mm 480mm - 915mm 970mm -
10 13/16ths" 18 7/8ths" - 36" 38 3/16ths" -
3
Fitting Kit EN
K997W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
4
Fitting Kit EN
K997W
Fitment FRONT ONLY
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
5
Fitting Kit EN
K997W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
6
Fitting Kit EN
K997W
●Remove as shown.
●Mark as shown.
Fitment Front Bar Only
●Use drill bit supplied, to drill holes in
marked positions.
7
Fitting Kit EN
K997W
●Re-install rubber ditch mould back into roof
channel and click into place.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all items.
●Refer to the underside of the pad for the
part number.
8
Fitting Kit EN
K997W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 224
B = 225
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Tighten the plastic knob. The side with the
nut showing should be facing up.
9
Fitting Kit EN
K997W
●Ensure the plastic knob is in the position
shown when fully tightened.
●Repeat at other end.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
●If crossbars are removed, please install the
rubber plugs into the ditch moulding.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K199 User manual
Prorack
Prorack Fitting Kit K440 User manual
Prorack
Prorack K1226 User manual
Prorack
Prorack EXP360 User manual
Prorack
Prorack K774 User manual
Prorack
Prorack K1163 User manual
Prorack
Prorack K681 User manual
Prorack
Prorack K686 User manual
Prorack
Prorack K471W User manual
Prorack
Prorack K137 Operation and installation manual
Prorack
Prorack K514 User manual
Prorack
Prorack K1007 User manual
Prorack
Prorack K537 User manual
Prorack
Prorack K462 User manual
Prorack
Prorack K443 User manual
Prorack
Prorack PR3217 User manual
Prorack
Prorack K758 User manual
Prorack
Prorack K165 Operation and installation manual
Prorack
Prorack K450 User manual
Prorack
Prorack K530 User manual
