Prorack K178 User manual

K178

Fitting Kit

EN Fitting Instructions for Basic Carrier

x 4 x 4 x 4

Revision No: 3C 1

Fitting Kit K178

MAX kgs (lbs)

W/P WHD

Mitsubishi

380, 4dr Sedan Oct 05-08 AU 50 kgs (110 lbs) 50 kgs (110 lbs)

380, 4dr Sedan Oct 05-08 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)

Galant, 4dr Sedan 04-12 US 50 kgs (110 lbs) 50 kgs (110 lbs)

Galant, 4dr Sedan 07-12 CN 50 kgs (110 lbs) 50 kgs (110 lbs)

2

Fitting Kit K178

X

A B C 1 2 3

380, 4dr Sedan Oct 05-08 (AU) -300mm 350mm - 931mm 919mm -

-11 -13/16ths" 13 3/4ths" - 36 5/8ths" 36 3/16ths" -

380, 4dr Sedan Oct 05-08 (NZ) -300mm 350mm - 931mm 919mm -

-11 -13/16ths" 13 3/4ths" - 36 5/8ths" 36 3/16ths" -

Galant, 4dr Sedan 04-12 (US) -300mm 350mm - 931mm 919mm -

-11 -13/16ths" 13 3/4ths" - 36 5/8ths" 36 3/16ths" -

Galant, 4dr Sedan 07-12 (CN) -300mm 350mm - 931mm 919mm -

-11 -13/16ths" 13 3/4ths" - 36 5/8ths" 36 3/16ths" -

3

Fitting Kit EN

K178

First Time Installation

●Remove parts from inside the package and

check. Contact your dealer if any parts are

missing or damaged.

●This kit fits type A, B, C and D.

●These instructions show type A crossbar

fitted. They also apply to type B, C and D.

NOTE: Clamp images in these instructions may

not be representative of the clamps in this kit

4

Fitting Kit EN

K178

●Use keys to remove covers.

●Use hex screwdriver to reverse adjusting

screw 10 turns.

●Press adjusting screw and pull crossbar

legs out. Refer to the crossbar instructions

for crossbar adjustment method.

●Ensure each end of the crossbar is

adjusted equally.

5

Fitting Kit EN

K178

●Remove locking screw.

●Apply protective strip as shown.

Trim if required.

●Attach clamp to each leg. NOTE; clamps

may have labels showing their positions on

the vehicle (For example; "Front Right").

6

Fitting Kit EN

K178

●Refit locking screw so that it goes through

the hole in the clamp. Do not begin to

tighten the locking screw.

●Fit rubber pads (supplied with fitting kit) to

foot.

●Make sure the pad fits into the holes

underneath the foot.

7

Fitting Kit EN

K178

Fitment

●Place crossbar on vehicle. Minimum

recommended spacing between the bars is

700mm (27 1/2") (unless otherwise stated).

●Clamps directly to edge of roof under the

doors

●Please check the front of this manual for

information relating specifically to your

vehicle.

●Press adjusting screw to adjust the leg

positions on the crossbar.

●Tighten adjusting screw to 5 Nm (3.7 ft lb)

hand tight.

8

Fitting Kit EN

K178

●Tighten locking screw on both legs evenly.

●Check crossbar is securely attached to the

vehicle.

●Use keys to fit and lock covers

9

Fitting Kit EN

K178

CAUTION: Recheck all fasteners immediately after

a load is applied to the crossbars.

Regularly check screws are tight.

10

This manual suits for next models

1

Table of contents

Other Prorack Automobile Accessories manuals

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual