Prorack K682 User manual
K682
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4 x 8
x 4 x 2 x 2 x 4
x 4 x 4 x 4
Revision No: 1A 1
Fitting Kit K682
MAX kgs (lbs)
W/P WHD
Holden
Colorado 7 , 5dr SUV 13-+ NZ 75 kgs (165 lbs) 100 kgs (220 lbs)
Colorado 7 , 5dr SUV 13-+ AU 75 kgs (165 lbs) 100 kgs (220 lbs)
Chevrolet
Trailblazer , 5dr SUV 13-+ ZA 75 kgs (165 lbs) 100 kgs (220 lbs)
2
Fitting Kit EN
K682
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K682
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Set bars to length (revert to rear of these
instructions).
●Clamps onto flush roof rail. Pins locate on
inside of rail.
4
Fitting Kit EN
K682
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Remove both pins from each leg. Use
tapered end of spanner located inside left
hand cover to assist.
5
Fitting Kit EN
K682
●Detach foot from leg. Store loose parts in a
safe place.
●Repeat for all legs.
●Select four feet assemblies and match the
left and right assemblies to the left and
right roof rack legs.
●Assemble foot from kit into leg by pressing
it down.
●Ensure foot interlocks with leg.
●Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
●Do not over tighten.
●Repeat for all legs.
6
Fitting Kit EN
K682
●Use two M5 x 12 mm self tapping screws to
secure the assembly onto the leg.
●Do not over tighten.
Fitment
●Apply protective strip as shown.
Trim if required.
●Using the Hex Key and the capscrews,
secure the clamps to the vehicle.
●Do not tighten at this stage
●Ensure spring washer is between clamp
and the head of the screw.
7
Fitting Kit EN
K682
●Place crossbar foot over clamp.
●Ensure back edge of foot sits flush with the
back edge of vehicle roof rail.
●Slide clamp through opening in leg.
●Using the Hex Key and the capscrews,
secure the clamps to the vehicle.
●Ensure spring washer is between clamp
and the head of the screw.
8
Fitting Kit EN
K682
●Thread the coach bolt through the clamp
and the leg.
●Tighten the red plastic knob.
●Ensure the red plastic knob is in the
position shown when fully tightened.
●Do not over tighten.
●Repeat for all four positions.
●Use keys to fit and lock covers
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K682
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K426 User manual
Prorack
Prorack K121 User manual
Prorack
Prorack K162 User manual
Prorack
Prorack K311 User manual
Prorack
Prorack K388 User manual
Prorack
Prorack K447 User manual
Prorack
Prorack K938 User manual
Prorack
Prorack K136 User manual
Prorack
Prorack K992 User manual
Prorack
Prorack K069 User manual
Prorack
Prorack K113 User manual
Prorack
Prorack K340 User manual
Prorack
Prorack K100 User manual
Prorack
Prorack K797 User manual
Prorack
Prorack K1188 User manual
Prorack
Prorack K174 User manual
Prorack
Prorack K823 User manual
Prorack
Prorack K465 User manual
Prorack
Prorack K577 Operation and installation manual
Prorack
Prorack K040 User manual
