Prorack K458 User manual
K458
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 2
x 2
Revision No: 5C 1
Fitting Kit K458
MAX kgs (lbs)
W/P WHD
Toyota
Prius , 5dr Hatch 09-12 ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
Prius , 5dr Hatch 09-12 EU 60 kgs (132 lbs) 60 kgs (132 lbs)
Prius , 5dr Hatch 09-12 US 60 kgs (132 lbs) 60 kgs (132 lbs)
Prius , 5dr Hatch Aug 09-12 NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Prius , 5dr Hatch Jul 09-Mar 12 AU 60 kgs (132 lbs) 60 kgs (132 lbs)
2
Fitting Kit EN
K458
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K458
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K458
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 613A
B = 614A
5
Fitting Kit EN
K458
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K458
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-248
B = 11-04-249
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K458
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K458
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K458
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K178 User manual
Prorack
Prorack K710 User manual
Prorack
Prorack K462 User manual
Prorack
Prorack K554 Operation and installation manual
Prorack
Prorack K646 User manual
Prorack
Prorack K1222 User manual
Prorack
Prorack K403 Operation and installation manual
Prorack
Prorack K301 User manual
Prorack
Prorack K510 User manual
Prorack
Prorack K683 User manual
Prorack
Prorack K598 User manual
Prorack
Prorack K868 User manual
Prorack
Prorack P15 User manual
Prorack
Prorack K723 User manual
Prorack
Prorack K943 User manual
Prorack
Prorack K557 User manual
Prorack
Prorack K340 User manual
Prorack
Prorack K570 User manual
Prorack
Prorack K495 User manual
Prorack
Prorack K436 User manual
