Prorack K358 User manual
K358
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
Revision No: 5E 1
Fitting Kit K358
MAX kgs (lbs)
W/P WHD
Honda
Accord, 4dr Sedan 08-12 US 50 kgs (110 lbs) 50 kgs (110 lbs)
Accord, 4dr Sedan Feb 08-12 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Accord, 4dr Sedan Feb 08-12 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit K358
X
A B C 1 2 3
Accord, 4dr Sedan 08-12 (US) -215mm 420mm - 892mm 865mm -
-8 -7/16ths" 16 9/16ths" - 35 1/8ths" 34 1/16ths" -
Accord, 4dr Sedan Feb 08-12 (AU) -215mm 420mm - 892mm 865mm -
-8 -7/16ths" 16 9/16ths" - 35 1/8ths" 34 1/16ths" -
Accord, 4dr Sedan Feb 08-12 (NZ) -215mm 420mm - 892mm 865mm -
-8 -7/16ths" 16 9/16ths" - 35 1/8ths" 34 1/16ths" -
3
Fitting Kit EN
K358
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K358
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K358
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 474A
B = 475A
6
Fitting Kit EN
K358
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
7
Fitting Kit EN
K358
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8
Fitting Kit EN
K358
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9
Fitting Kit EN
K358
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Prorack Automobile Accessories manuals
Prorack
Prorack K877 Operation and installation manual
Prorack
Prorack K410 User manual
Prorack
Prorack K820 User manual
Prorack
Prorack K786 User manual
Prorack
Prorack K311 User manual
Prorack
Prorack K686 User manual
Prorack
Prorack PR3501 User manual
Prorack
Prorack K623 User manual
Prorack
Prorack K783 User manual
Prorack
Prorack K619 User manual
Prorack
Prorack K145 User manual
Prorack
Prorack K997 User manual
Prorack
Prorack K1013 User manual
Prorack
Prorack K485 User manual
Prorack
Prorack K067 User manual
Prorack
Prorack K367 Operation and installation manual
Prorack
Prorack K1214 User manual
Prorack
Prorack K540 User manual
Prorack
Prorack K1008 User manual
Prorack
Prorack K434 User manual
