Premier Mounts MVW463 User manual

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1321 S. State College Blvd., Fullerton, CA 92831 USA

Installation Guide

MVW463

Video Wall Frame

Phillips Head Screwdriver

Level

Required for installation

Warning Statements

MVW463

Installation Guide

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Prior to the installation of this product, these installation instructions must be read and completely understood. Keep these installation instructions in an easily

accessible location for future reference.

Videowall Tolerance Disclaimer

Premier Mounts manufactures all videowall frames with a maximum tolerance of 0.015 inches between the mounting pattern and the frames outside perimeters.

Even though Premier Mounts provides different hardware options for precision alignments, alignment issues may occur due to higher tolerance levels for display

mounting patterns or the structural integrity of the mounting surface, which may react to the total weight of the attached structure.

Proper installation procedure by a qualied service technician must be followed, as outlined in these installation instructions. Failure to do so could result in

property damage, serious personal injury, or even death.

Safety measures must be practiced at all times during the assembly of this product. Use proper safety equipment and tools for the assembly procedure to

prevent personal injury.

Premier Mounts does not warrant against damage caused by the use of any Premier Mounts product for purposes other than those for which it was designed or

damage caused by unauthorized attachments or modications, and is not responsible for any damages, claims, demands, suits, actions or causes of action of

whatever kind resulting from, arising out of or in any manner relating to any such use, attachments or modications.

At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result from dropping or mishandling your

electronic equipment.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires on the oor.

Cutting or drilling into an electrical line may cause serious personal injury.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact.

Do not install on a structure that is prone to vibration, movement or chance of impack. Failure to do so could result in damage to the at-panel and/or

damage to the mounting surface.

Tape Measure

Ladder

Rigging Hardware M6 Allen Wrench

Heavy-Duty Steel Tube Long Enough

to Hang MVW463(s)

Page 2

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Video Wall Frame

(Qty 1)

6mm Quick-Release

Button (Qty 4)

8mm Quick-Release

Button (Qty 4)

Universal Spacer

(Qty 4)

M8 x 16mm Set Screw

(Qty 4)

M6 x 20mm Screw

(Qty 4)

M6 x 25mm Screw

(Qty 4)

M8 x 16mm Screw

(Qty 8)

M8 x 20mm Screw

(Qty 4)

M8 x 25mm Screw

(Qty 4)

Included Components

Features

Page 3

They can be installed in either portrait or landscape orientation. Quick-release buttons make it easier than ever to install the displays, which can be

attached to the front and/or back of the MVW463. You can join multiple MVW463’s horizontally and/or vertically to create a video wall.

2” Cutouts

Insert the tubing of Premier Mounts’

dual-pole cart or stand and adjust the

height of the MVW463 by tightening

set screws.

2” Corner Cutouts

The corner cutouts can be used

to insert 2” tubing for ying the

MVW463 from above.

Outer Keyhole Mounting Slot

Use these slots to quickly fasten the

display to the MVW463.

Alignment Tab

Use these tabs to

quickly align multiple

MVW463’s next to

each other.

Inner Keyhole Mounting Slot

Use these slots to quickly fasten the

displays to the MVW463.

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1Dual-Pole Cart or Stand Installation Illustrations show only some of the installation congurations

possible with the MVW463’s.

Figure 1

Make sure the MVW463 keyhole mounting slots are in the correct orientation for portrait or landscape orientation (Figure 2), so that they can support

the at-panel display(s) later.

Figure 2

The keyhole mounting slots

should point downward.

Portrait

Orientation

Landscape

Orientation

Insert tubes through the holes of the frames shown in Figure 1.

Page 4

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

The arrows show where the M8 x 16mm pan Phillips screws can go from

inside to fasten MVW463’s together.

Figure 1

Full View Top/Bottom View Side View

If you are fastening multiple MVW463’s, use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames

(Figure 1).

To safely install rows of multiple MVW463’s, fasten them rst in individual rows, then insert the tubing of the dual-pole cart or stand into each

row. After that, fasten the rows together (Figure 2).

Figure 2

An example of fastening multiple

MVW463’s in rows.

Page 5

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1) Slide the MVW463 to the desired height on the dual-pole cart or stand.

2) Insert four (4) M8 x 10mm set screws into the MVW463 screw holes near

the tubing (see drawing).

3) Tighten the screws against the MVW463 and tubing.

Back-View Closeup of MVW463

Tubing of Cart or Stand

M8 x 10mm Set Screw

All at-panel display illustrations are

shown for example purposes only.

• If you are installing a Samsung 460UT or Samsung 460UT-2,

attach four (4) 8mm quick-release buttons and four (4) M8 x 20mm

pan Phillips screws to the display’s back mounting holes.

• If you are installing an NEC X461UN or NEC X461UN2, attach four

(4) universal spacers, four (4) 6mm quick-release buttons and four

(4) M6 x 30mm pan Phillips screws to the display’s back mounting

holes.

Do not over tighten the screws.

Attach the at-panel display to either side of the MVW463 by inserting the

display’s quick-release buttons into the keyhole mounting slots on the MVW463,

locking them into place.

Depending on your videowall conguration, install displays working from the

bottom frame up.

The Samsung 460UT or Samsung 460UT-2 should t into the MVW463’s outer

keyhole mounting slots.

The NEC X461UN or NEC X461UN2 should t into the MVW463’s inner keyhole

mounting slots.

Keyhole Mounting Slot

Universal spacers are needed only for

the NEC X461UN or NEC X461UN2 to

prevent their display handle from hitting

the MVW463.

Page 6

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

6Flying Installation Illustrations show only some of the installation

congurations possible with the MVW463’s.

Figure 1

Figure 2

Figure 3

The keyhole mounting slots

should point downward.

MVW463

Heavy-Duty Steel Tube

MVW463’s

Heavy-Duty Steel

Tube

Illustrations show only some of the

installation congurations possible with

the MVW463’s.

If ying the MVW463(s), insert a heavy-duty steel tube (not included) into the frames’ upper 2” circular cutouts (Figure 1).

Appropriate tubing and rigging hardware must be used to support a minimum of 4 times the combined weight of all the at-panel displays and

MVW463’s used.

The steel tube must be long enough to span the entire width of the frame(s) (Figure 2).

Make sure the MVW463 keyhole mounting slots point down so that they can suport the at-panel display(s) later (Figure 3).

Page 7

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Page 8

The arrows show where the M8 x 16mm pan Phillips screws can go from

inside to fasten MVW463’s together.

Figure 1

Full View Top/Bottom View Side View

If you are fastening multiple MVW463’s, use the M8 x 16mm pan Phillips screws provided to fasten them together from inside the frames (Figure 1).

To safely install rows of multiple MVW463s, fasten them rst in individual rows, then fasten the rows together. After that, insert the heavy-duty plastic tube

(Figure 2).

Figure 2

An example of fastening multiple

MVW463’s in rows.

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1) Slide the MVW463 to the desired position against the tube.

2) Insert two (2) M8 x 10mm set screws into the corner screw holes above

the tube (Figure 1).

3) Tighten the screws against the MVW463 and the tube.

4) Inside the MVW463, wrap and secure rigging/ying hardware (not

included) around the tube (Figure 2).

WARNING!

Do not install the rigging/ying hardware or y the MVW463(s) unless

you are a qualied A/V installation professional.

Front-View Closeup of

MVW463

M8 x 10mm Set Screw Figure 1

Figure 2

Rigging/Flying Hardware

Heavy-Duty Steel

Tube

Heavy-Duty Steel Tube (inside the

MVW463)

All at-panel display

illustrations are shown for

example purposes only.

Universal spacers are needed

only for the NEC X461UN or

NECX461UN2 to prevent its

display handle from hitting the

MVW463.

• If you are installing a Samsung 460UT or Samsung 460UT-2, attach

four (4) 8mm quick-release buttons and four (4) M8 x 20mm pan

Phillips screws to the display’s back mounting holes.

• If you are installing an NEC X461UN or NEC X461UN2, attach four (4)

universal spacers, four (4) 6mm quick-release buttons and four (4) M6

x 30mm pan Phillips screws to the display’s back mounting holes.

Do not over tighten the screws.

Attach the at-panel display to either side of the MVW463 by inserting the

display’s quick-release buttons into the keyhole mounting slots on the MVW463,

locking them into place.

Depending on your videowall conguration, install displays working from

the bottom frame up.

The Samsung 460UT or Samsung 460UT-2 should t into the MVW463’s

outer keyhole mounting slots.

The NEC X461UN or NEC X461UN2 should t into the MVW463’s inner

keyhole mounting slots.

Keyhole Mounting

Slot

Page 9

Installation Guide

MVW463

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Page 10

1) Use the rigging/ying hardware to safely suspend the MVW463(s) overhead.

2) To set the tilt angle, attach additional cables to the bottom of the frames and

pull to the desired angle (see drawing).

Re-check all hardware and installation for proper tightness and security.

Rigging/Flying Hardware

Pull additional cables at the bottom of

the frames to adjust the tilt.

Table of contents

Other Premier Mounts Rack & Stand manuals

Premier Mounts

Premier Mounts LPWS100 User manual

Premier Mounts

Premier Mounts Universal Projector Mount PBL-UMS User manual

Premier Mounts

Premier Mounts Polaris MAG-EXT User manual

Premier Mounts

Premier Mounts AM225 User manual

Premier Mounts

Premier Mounts Swingout Arm AM3 User manual

Premier Mounts

Premier Mounts ECM-3763S User manual

Premier Mounts

Premier Mounts SCM-103 User manual

Premier Mounts

Premier Mounts PP-5 User manual

Premier Mounts

Premier Mounts Universal Flat Mount FM3 User manual

Premier Mounts

Premier Mounts SHLF-VC User manual

Premier Mounts

Premier Mounts Universal Tabletop Stand PSD-TTS Guide

Premier Mounts

Premier Mounts PCM-MS2 User manual

Premier Mounts

Premier Mounts PFC-OMND User manual

Premier Mounts

Premier Mounts CONVERGENT SAM-IFJ Series User manual

Premier Mounts

Premier Mounts CTM-MS1 User manual

Premier Mounts

Premier Mounts PSD-TL User manual

Premier Mounts

Premier Mounts GB-PIPE1 User manual

Premier Mounts

Premier Mounts AST-2446-2 User manual

Premier Mounts

Premier Mounts RTM-L User manual

Premier Mounts

Premier Mounts EST200 User manual

Premier Mounts

Premier Mounts LMVSP User manual

Premier Mounts

Premier Mounts FLIP User manual

Premier Mounts

Premier Mounts MVWC-3X3 User manual

Premier Mounts

Premier Mounts LMVSP User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 