Premier Mounts FLIP User manual

INSTALLATION INSTRUCTIONS

FLIP

Flip-Down LCD Mount

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada –

Phone: 800-368-9700

Fax: 800-832-4888

EUROPE

Swallow House,

Shilton Industrial Estate,

Shilton, Coventry, England CV79JY

Phone: +44 (0) 2476 614700

Fax: +44 (0) 2476 614710

Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044

©Premier Mounts 2009

9531-017-011-00

Page 2 Installation Instructions

Table of Contents

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS

PRODUCT FOR PURPOSES OTHERTHAN THOSE FORWHICH ITWAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED

ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS,

ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELAT-

ING TO ANY SUCH USE,ATTACHMENTS OR MODIFICATIONS.

THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST 5 TIMES THE WEIGHT OF THE FLAT PANEL. IF

NOT, THE WALL STRUCTURE MUST BE RE-INFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE

TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD

RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER

SAFETY GEARAND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.

Warning Statements

Indicates that the power plug is to be disconnected

from the power outlet.

Safety precautions must be taken at all times.

Warning and Caution statements.

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the ﬂat panel

and/or damage to the mounting surface.

Do not install near heater, ﬁreplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in

damage to the ﬂat panel and could increase the risk of ﬁre.

At least two qualiﬁed people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the

ﬂat panel.

Contact Premier Mounts with any questions -

(800) 368-9700.

Warning Statements 2

Parts List 3

Installation Tools 3

FLIP Mount Location 4

Hardwood Cabinet Installation 5

Softwood Cabinet Installation 6

Mount Installation - Wall Surface (Optional) 7

Attaching the Flat Panel 8

FLIP Mount Adjustments 9

Final Adjustments 9

Technical Speciﬁcations 10

Warranty 11

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND

COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND

PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE

REFERENCE.

It is recommended that a maximum of 5/8” plaster board be used when mounting to wooden studs.

FLIP Mount

Installation Instructions Page 3

Parts List

M5 x 10mm Flat Head Screw (Qty 1)

Flip Mount (Qty 1)

M4 x 10mm Combo Screw (Qty 4)

1/4-20 x 5/8” Combo Screw (Qty 2)

1/4-20 Tee Nut (Qty 2)

#14 x 2” Wood Screw (Qty 2)

Wall Stud Applications #14 x 7/8” Wood Screw (Qty 2)

Under-counter Applications

FLIP Mount

Congratulations on the purchase of your new Premier Mounts FLIP ﬂat panel mount. This mount is shipped with all

proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before

beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Premier Mounts

(800) 368-9700.

Installation Tools (not supplied)

Screwdriver

1/8” Drill Bit

(Wood Stud Installation) Electronic Stud Finder Drill

Tape

Measure

Hammer

5/32” Allen Wrench

Pencil

5/16” Drill Bit

(Tee Nut Installation)

The M5 ﬂat head screw will prevent

the FLIP mount mounting plate from

rotating 360°.

Page 4 Installation Instructions

FLIP Mount

Before drilling, make sure that there is enough room to lower and raise the display. For example, when the display is put in

the “up” position, it should not hit the wall and should be even with the front of the cabinet.

FLIP Mount Location

When mounting the FLIP mount to the underside of a cupboard, careful consideration must be taken.

The following steps will help in determining the placement of the FLIP mount (please see diagram above):

Step 1. Attach the ﬂat panel to the FLIP mount (SEE PAGE 8).

Step 2. Put the FLIP mount in the “up” position.

Step 3. Place the FLIP mount base ﬂush on the underside of the cupboard.

Step 4. Slide ﬂat panel and FLIP mount to the rear of the cupboard surface until the bottom edge of the ﬂat panel is a minimum 1” from

the wall.

Step 5. Use a pencil to mark where the two mounting holes are. This will be the location where your pilot holes will be drilled.

Mount placement will be primarily determined by the size of the ﬂat panel being used.

There must be enough clearance for the FLIP mount and ﬂat panel to be adjusted without interfering with the wall, counter

top surface and the overhead cupboard (see diagram below).

FLIP

Mount

Flat

Panel

“UP” Position

“DOWN” Position

Clearance

Cupboard

Counter top

Installation Instructions Page 5

Hardwood Cabinet Installations

Step 1. Place the FLIP Mount base on the mounting

location and mark (using a pencil) where the FLIP

will be mounted.

FLIP Mount

This distance was

determined in the

FLIP Mount Location

section.

Cupboard FLIP

Mount

Prior to drilling into the underside of the

cabinet, it is strongly recommended that

all items be removed from the cabinet.

Step 2. Using a 1/8” drill bit and portable

drill, pre-drill both pilot holes at the

marked locations.

Marking

1/8” Drill

Bit

Drill

Wood screws are recommended when mounting the FLIP mount onto hardwood surfaces.

The FLIP mount base may be used as a

template when marking the mount location.

Page 6 Installation Instructions

FLIP Mount

Step 3. Line the FLIP Mount up with the two

pre-drilled mounting holes and use

two (2) #14 x 7/8” wood screws and

secure the FLIP Mount to the underside

of the cabinet using a screwdriver.

#14 x 7/8” Wood

Screw

Screwdriver

FLIP Mount

Do NOT over-tighten the wood

screws, as this could cause the

threads to strip out the wood

inside the cabinet enclosure.

Softwood Cabinet Installation

1/4-20 Tee Nut and screws are recommended when installing the FLIP mount into softwood surfaces.

Step 1. Use a 5/16” drill bit and drill to pre-drill the tee nut pilot holes in the underside of the cupboard.

Step 2. After drilling the mounting holes, open the cupboard door and place two (2) 1/4 - 20 tee nuts into each hole (see inset above).

Use a hammer to gently tap into place.

Step 3. Line the FLIP Mount up with the two pre-drilled mounting holes.

Step 4. Using a screwdriver, insert and tighten two (2) 1/4 - 20 x 5/8” screws and attach the FLIP Mount to the underside of the

cabinet.

1/4-20 x 5/8”

Screw

Screwdriver

FLIP Mount

1/4-20 Tee

Nut

1/4-20 Tee

Nut

Cupboard

Pre-drilled

Hole

(5/16” drill

bit)

Installation Instructions Page 7

FLIP Mount

Step 5. Using a portable drill, insert and tighten two (2)

#14 x 2” wood screws.

Do NOT over-tighten the wood screws, as this

could cause the threads to strip out the wood

inside the wall stud.

1/8” Drill

Bit

Step 4. Using a 1/8” drill bit, pre-drill both pilot

holes at the marked locations.

Before drilling the pilot holes, line

up the mounting holes with the

pencil marks and level the FLIP

mount, if needed.

Wall Stud

#14 x 2” Wood Screw

Screw driver

FLIP Mount

Mount Installation - Wall Surface (Optional)

Wall Stud

Electronic

Stud Finder

Step 1. If the location where the ﬂat panel will be

installed is acceptable, use a stud ﬁnder to

determine the exact center of each stud.

Step 2, Once a wood stud has been located, mark

this spot with a pencil. This will be the upper

mounting point.

Step 3. Mark the lower mounting point as well, once

the upper mounting point has been marked.

Mark

Wall Stud

FLIP Mount

Page 8 Installation Instructions

FLIP Mount

Attaching the Flat Panel

Step 1. Locate the mounting points that are on the back of the ﬂat panel.

Step 2. Line up the mounting points on the ﬂat panel with the corresponding mounting holes on the FLIP mount.

Step 3. Loosely attach the upper two (2) M4 x 10 mounting screws.

Step 4. Insert the screw heads into the corresponding keyhole mounting slots that are on the FLIP mount.

Step 5. With the FLIP mount securely attached, insert and tighten the two (2) lower M4 x 10 mounting screws.

Step 6. Use a screwdriver to tighten all mounting hardware at this time.

M4 x 10mm

Screw

Flat Panel

FLIP Mount

Keyhole Mounting

Slot

M4 x 10mm

Screw

Mounting Point

M5 x10mm Flat Head Screw (see NOTE:)

If you chose not to use the 360° feature of the FLIP mount, please insert and tighten one (1) M5 x 10mm ﬂat head screw

into any one of the four mounting point locations (please see below for mounting points). The M5 x 10mm ﬂat head screw

will prevent the FLIP mount from rotating 360°.

If you chose not to use the 360° feature of the FLIP mount, please insert and tighten one (1) M5 x 10mm ﬂat head screw

into any one of the four mounting point locations (please see above for mounting points). The M5 x 10mm ﬂat head screw

will prevent the FLIP mount from rotating 360°.

Installation Instructions Page 9

FLIP Mount

FLIP Mount Adjustments

Vertical Adjustment Left-to-Right 360° Rotation

Adjustment

360° Rotation Adjustment

Final Adjustments

The FLIP mount has pivots points that

allow the mount to be easily adjusted. Once

the adjustments have been made, the pivot

points will need to be tightened. Please refer

to the steps below to tighten the pivot point

screws.

Step 1. Make sure the FLIP mount has

been adjusted to the determined

viewing angle.

Step 2. Locate each pivot point.

Step 3. Use the 5/32” Allen wrench

(supplied) to tighten each pivot

point screw.

Pivot Point

Screw

5/32” Allen

Wrench

Pivot Point

Screw

5/32” Allen

Wrench

Tilt Adjustment

Vertical/Lateral

Adjustment

Page 10 Installation Instructions

Technical Speciﬁcation

All measurements are in inches [mm].

FLIP Mount

Table of contents

Other Premier Mounts Rack & Stand manuals

Premier Mounts

Premier Mounts MM-CB3 User manual

Premier Mounts

Premier Mounts CONVERGENT SAM-IFJ Series User manual

Premier Mounts

Premier Mounts LMVF User manual

Premier Mounts

Premier Mounts Convergent UNI-UPS-A CLD User manual

Premier Mounts

Premier Mounts PDS-PLUS User manual

Premier Mounts

Premier Mounts MVWS-3X3 Series User manual

Premier Mounts

Premier Mounts Rotary RTM-S User manual

Premier Mounts

Premier Mounts SpiroLock SPI-PRO User manual

Premier Mounts

Premier Mounts PBM-760L User manual

Premier Mounts

Premier Mounts AM80 User manual

Premier Mounts

Premier Mounts AM225 User manual

Premier Mounts

Premier Mounts PBL-200 User manual

Premier Mounts

Premier Mounts ECM-D70T User manual

Premier Mounts

Premier Mounts FPS-200 User manual

Premier Mounts

Premier Mounts Convergent Series User manual

Premier Mounts

Premier Mounts PP-HDFCP User manual

Premier Mounts

Premier Mounts AM500 User manual

Premier Mounts

Premier Mounts PP-FCTA-QL User manual

Premier Mounts

Premier Mounts ECM-3763D User manual

Premier Mounts

Premier Mounts MVWC-2X2 User manual

Premier Mounts

Premier Mounts Convergent Series User manual

Premier Mounts

Premier Mounts UFA User manual

Premier Mounts

Premier Mounts CTM-MS1 User manual

Premier Mounts

Premier Mounts 7170-0977 Series User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 