Premier Mounts EST200 User manual
Single-Stud/Dual-Stud
Short-Throw Projector Wall Mount
Model: EST100/EST200
9530-011-001-0X Rev.1
INSTALLATION INSTRUCTIONS
NORTH AMERICA
1321 S. State College Blvd
Fullerton, CA 92831 USA
USA and Canada
Phone: 1-800-368-9700
Fax: 1-800-832-4888
Other Locations
Phone: (001) 714-632-7100
Fax: (001) 714-632-1044
Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Table of Contents
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR
MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION
OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR
MODIFICATIONS.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the
projector.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is
recommended.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in
wall. Cutting/drilling into an electrical line may cause serious injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact
Contact Premier Mounts with any questions
(800) 368-9700
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN-
DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water
damage to the mounting surface.
EST100/EST200
Weight Capacity
Maximum projector weight: 25 lbs. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE
(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE
WALL STRUCTURE MUST BE REINFORCED.
Warning Statements
Heading 1
Weight Capacity 2
Warning Statements 2
Installation Tools 3
Parts List 3
Features 4
Determining the Installation Height 5
Wood Stud Installation 6
Throw Distance Calculation 10
Projector Installation 10
Attaching the Mount Carriage 11
Multiple Mounting Point Installation 12
Single Mounting Point Installation 14
Attaching the Mount Carriage to the Projector Arm 15
Cable Routing (Optional) 16
Securing the Projector (Optional) 16
Mount Adjustment 17
Technical Specications 17
Warranty 18
Disclaimer 18
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 3
Projector Arm
(Qty 1)
Mount Carriage
(Qty 1)
Phillips Screwdriver ⅛˝ Drill Bit Electronic Stud Finder
Drill Level
Dual-Stud Back Plate
(Qty 1)
EST100/EST200
Back Plate Hardware Pack (included only with the EST200)
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Make sure your Premier Mounts product has the following hardware and components before beginning installation. If
there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.
EST100/EST200 Hardware
M2.5 x 8mm
Security Screw (Qty 4)
M2.5 x 10mm
Security Screw (Qty 4)
M3 x 16mm
Security Screw (Qty 4)
M3 Flat Washer
(Qty 4)
M4 x 12mm
Security Screw (Qty 4)
M5 x 10mm
Security Screw (Qty 3)
M5 x 12mm
Security Screw (Qty 4)
M6 x 12mm Security
Screw (Qty 4)
#14 x 2” Wood Screw
(Qty 2)
¼-20 x 5/16″ Security
Screw (Qty 1)
M5 Security Wrench
(Qty 1)
Barrel Cap
(Qty 4)
M5 x 10mm
Security Screw (Qty 2)
#14 x 2” Wood Screw
(Qty 2)
M5 Flat Washer
(Qty 4)
Sleeve Bushing
Nylon (Qty 4)
Projector Arm
Cover Plate (Qty 1)
Page 4 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
EST100/EST200
THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION.
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal
injury or damage to property.
Warning
Step 1
Step 2
Step 3
Are you installing the single-stud EST100 or the dual-stud EST200?
If EST100, continue to the “EST100 Installation” section below.
If EST200, go to the “EST200 Installation” section on page 8.
EST100 Installation
After the pilot holes have been drilled, use
two (2) #14 x 2˝ wood screws to mount the projector arm to the wooden stud.
Once the mounting points have been marked, use a
⅛˝ drill bit and portable drill to drill the pilot holes.
Drill Marking
Wood Stud
Marking
Projector
Arm
#14 x 2” Wood Screw
Use two (2) M5 x 10mm security screws to attach the projector arm cover plate
to the projector arm.
Wood stud not shown
Go to the “Throw Distance Calculation” section on
page 10.
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 5
EST100/EST200
Step 2
Step 1
Step 3
Step 4
Use an electronic stud nder (not supplied) to
locate the center of the stud that is in the wall.
Wood Stud
Height
Mark
(from page 5)
Mounting Point
Mark
Use a pencil to mark the rst mounting point, just
above your height mark (from page 5).
Wood Stud
Marking
Back
Plate
Once the mounting points have been marked, use a
⅛˝ drill bit and portable drill to drill the pilot holes. Drill Marking
Use the level to make sure the back plate is level from side to side.
Align one of the lower mounting slots of the back plate with the rst mounting
point mark and use a pencil to mark the rest of the mounting points.
Four (4) mounting points must be used. Two (2)
upper mounting points and two (2) lower mounting
points.
EST200 Installation
Stud nder
EST100/EST200
Page 6 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Step 5
Put the projector arm cover plate on the projector arm.
Projector Arm
Projector Arm
Cover Plate
Step 6
Place the projector arm assembly within the desired mounting slots on the
back plate.
Use four (4) M5 x 10mm security screws, four (4) M5 at washers and four
(4) sleeve bushing nylons to attach the projector arm assembly to the back
plate.
The elongated mounting slots in the back plate allow some lateral shift for
precisely adjusting the projector arm.
Use four (4) #14 x 2” wood screws to mount the back plate to the wooden studs
where the pilot holes are.
The elongated mounting slots in the back plate allow some lateral shift for
precise adjustments against the studs.
Proceed to the “Throw Distance Calculation” section on page 10.
Step 7
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 7
EST100/EST200
Attaching the Mount Carriage
Selecting the Mounting Hardware
Insert a small straw or toothpick into the threaded inserts
found on the bottom or top of the projector.
Use a pencil to mark the depth of the threaded insert on the
small straw or toothpick.
Mark the straw or toothpick 1/8” above the depth of the
threaded insert, as shown in Figure 1.
Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth using the
straw or toothpick’s 1/8” allowance mark.
Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick, as shown
in Figure 2 and Figure 3, do not use this screw. The
screw length must not bypass the mark.
Test each size of the screws provided. The correct screws
should thread easily into the mounting point and not pull out
when tension is applied.
Does your projector have multiple mounting points or a
single mounting point?
If your projector has multiple mounting points, proceed to the “Multiple
Mounting Point Installation” section.
If your projector has a single mounting point, skip to the “Single
Mounting Point Installation”.
Small Straw or Toothpick
Small Straw
or Toothpick
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Page 10 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
EST100/EST200
Step 2
Attach the mounting legs to the projector using the corresponding mounting
hardware.
Do not tighten the mounting hardware at this time.
Multiple Mounting Point Installation
Step 1
Locate the projector’s mounting points.
Position the mounting legs on the projector.
The mounting legs are pre-installed. Depending on the requirements of your
projector, you may remove one of the mounting legs.
The number and placement of mounting points on projectors varies
between projector manufacturers. Refer to you projector’s technical
specications for the number and location of the mounting points on
your specic projector.
Step 3
If the mounting legs need to be leveled, rotate the leveling barrels to level the
mounting bracket.
To raise the mounting legs, rotate the leveling barrel clock-wise. To lower the
mounting leg, rotate the leveling barrel counter clock-wise.
Raise or lower each of the mounting legs, by rotating the leveling barrels,
until all of the mounting legs are at an equal height.
• Lower the mounting leg by rotating the leveling
barrel counter-clockwise.
• Raise the mounting legs by rotating the leveling
barrel clockwise.
When the desired position is achieved, tighten the mounting screws to the
projector and then tighten the hex head leg screws with the M5 Allen wrench.
Screws shown for illustration
purposes only.
Mount carriage not shown.
Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 11
EST100/EST200
Step 5
Position the legs accordingly for best conguration. You may raise or lower
each leg independently by turning the leveling barrels.
Secure the legs to the mount carriage by screwing
M6 x 12mm security screws into the M6 square nut (do not overtighten) on
the mounting legs.
Verify the position of the integrated sliding M6 square nut in the mounting leg
relative to a nearby slot on the mount carriage.
If the M6 square nut is not aligned with any slot, you can use any thin
implement, such as a toothpick, to nudge it into alignment.
Sliding M6
Square Nut
Identify the projector’s approximate front-to-back center of gravity. Place
your hands on each side of the projector and gently lift it an inch from the
surface on which it is resting. Carefully adjust your grip on the projector until
it seems balanced from front-to-back. Mentally note the apparent center of
gravity.
Identify the projector’s approximate side-to-side center of gravity. Place your
hands on the front and back of the projector and gently lift it an inch from the
surface on which it is resting. Carefully adjust your grip on the projector until
it seems balanced from side-to-side. Mentally note the apparent center of
gravity.
Make sure the mount carriage is as close as possible to the projector’s
center of gravity.
Step 4
Side-to-Side
Center of Gravity
Front-to-Back
Center of Gravity
Mounting Hardware Too Long?
The depth of some projector mount points may prevent you from
tightening the M2.5 and M3 mounting hardware.
You can reduce the length of the M2.5 and M3 mounting hardware
by stacking up to a maximum of ve (5) M3 at washers inside the
leveling barrel.
Avoid stacking too many M3 washers; the mounting hardware must
thread into the projector mount point at least four (4) complete
turns.
Page 12 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
EST100/EST200
Step 7
Insert one (1) Barrel Cap (except for the security barrel) into the end of each
leveling barrel.
Go to the “Attaching the Mount Carriage to the Projector Arm” section on
page 15.
Step 6
Tighten the mounting screws which secures the mounting legs to the
projector.
Do not overtighten the mounting screws.
Single Mounting Point Installation
A single ¼-20 x 5/16″screw must be used to attach the mount carriage to the
projector if your projector has only one mounting point.
Do not overtighten the ¼-20 x 5/16″screw.
Proceed to the “Attaching the Mount Carriage to the Projector Arm” section
on page 15.
This manual suits for next models
2
Table of contents
Other Premier Mounts Rack & Stand manuals
Premier Mounts
Premier Mounts UFA User manual
Premier Mounts
Premier Mounts Universal Projector Mount PBL-UMS User manual
Premier Mounts
Premier Mounts FPS-200 User manual
Premier Mounts
Premier Mounts SpiroLock SPI-PRO User manual
Premier Mounts
Premier Mounts PSD-CAM User manual
Premier Mounts
Premier Mounts Cathedral Ceiling Adapter PP-TL User manual
Premier Mounts
Premier Mounts AST-2446-2 User manual
Premier Mounts
Premier Mounts PP-FCTA-QL User manual
Premier Mounts
Premier Mounts LMVSP User manual
Premier Mounts
Premier Mounts FLIP User manual
Premier Mounts
Premier Mounts RTM-L User manual
Premier Mounts
Premier Mounts AM100 User manual
Premier Mounts
Premier Mounts Nesting Cart Series User manual
Premier Mounts
Premier Mounts Universal Tabletop Stand PSD-TTS Guide
Premier Mounts
Premier Mounts UMB-DBTS User manual
Premier Mounts
Premier Mounts AST-1321 User manual
Premier Mounts
Premier Mounts PRC User manual
Premier Mounts
Premier Mounts Swingout Arm AM3 User manual
Premier Mounts
Premier Mounts LMV User manual
Premier Mounts
Premier Mounts PCM-MS2 User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
