Premier Mounts LMVSP User manual
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
2620 Palisades Drive, Corona CA, 92882
Installation Guide
LMVSP
Release Pop Out Ultra Slim Portrait Mount
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Included Components
Required for installation
LMVSP
Installation Guide
Maximum Flat Panel Weight:
100 lb. / 45.35 kg.
5/16” x 3” Lag Bolts
(Qty 4)
Thread Depth Indicator
(Qty 1)
Universal Spacers
(Qty 8)
Finned Anchors
(Qty 4)
M8 Washers
(Qty 4)
M8 Nylon Nut
(Qty 4)
5/16” Flat Washers
(Qty 4)
Universal Washers
(Qty 4)
Pencil Protective Eyewear
Electronic Stud Finder M6 or 1/4” Drill Bit 3/8” Masonry Drill Bit
Portable Drill
Phillips Head Screwdriver Socket Wrench
13mm or 1/2” SocketHammer
Level
M5 Allen Driver
(Qty 1)
M4 x 12mm (Qty 4)
M4 x 16mm (Qty 4)
M4 x 25mm (Qty 4)
M6 x 12mm (Qty 4)
M6 x 16mm (Qty 4)
M6 x 25mm (Qty 4)
M8 x 12mm (Qty 4)
M8 x 16mm (Qty 4)
M8 x 25mm (Qty 4)
Extension Bracket
(Qty 1 Pair)
Wall Mount
(Qty 1)
Bracket
(Qty 1 Pair)
Page 2
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
XX
1
3
2
4
Wood Stud Installation
1) Use a stud nder to determine the wall studs in the
vicinity of the mount.
2) Use a pencil to mark each of the wall studs.
Use a pencil to mark the upper right mounting location of the wall
stud.
Drill a “pilot hole” using a M6 or 1/4” drill bit on the stud that was
marked on the upper right.
1) Place the mount against the wall and align it with the pilot hole.
2) Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
the upper right pilot hole.
3) Use a socket wrench and a 13mm or 1/2” socket to tighten the
lag bolt.
XX
Page 3
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
5
7
6
1) Level the mount
2) Use a pencil to mark the remaining three (3) mounting locations.
Drill a “pilot hole” in each of the three (3) marks with a power drill and
a M6 or 1/4” drill bit.
1) Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
each pilot hole.
2) Tighten all lag bolts using a socket wrench and 1/2” socket.
Do not over tighten the lag bolts
Page 4
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
8
10 11
9
Concrete wall Installation
Two people recommended for this step; one person to level the
mount and another person to mark the mounting locations.
Drill a “pilot hole” in each of the four (4) mark areas with a 3/8”
masonry drill bit.
Insert the Finned Anchors into each hole. Lightly tap each Finned
Anchors into place with a hammer.
Insert the lag bolts and washers into the Finned Anchors. Tighten all
lag bolts using a socket wrench and 1/2” or 13mm socket.
Page 5
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
LMVSP ’s dedicated at-panel spacers are engineered with the knowledge
that aligning each at-panel on a large wall is time consuming and costly.
These model-specic spacers are available for most at-panels, which
signicantly reduces the installation time. (Call Customer Service to inquire
about model specic spacers.)
Installing OPTIONAL Model Specic Spacers
This spacer is shown for illustration purposes only. Your spacer may
look different depending on the display model you are installing.
1) Once your LMVSP is mounted in the desired location and is
level, align your spacer to the top left or right (depending on
your install direction) corner register tabs of your mount.
You may use commercially available hardware to secure the
spacer to the wall during installation (depending on the wall material).
You may utilize the same spacer for multiple LMVSP installations.
Start
Multiple LMVSP mounts can be installed using model specic spacers.
Simply repeat step one when installing each of the surrounding LMVSP
mounts. Use one spacer for each 2x2 installation by mounting it to the wall,
or utilize the same spacer as many times needed to complete an unlimited
LMVSP large matrix video wall.
1. Make sure the spacer is plumb and level and mark each corner where
the LMVSP will be mounted (or secure to the wall). It is best to start
from the bottom corner and work your way up.
2. Install the second mount working in a horizontal direction.
3. Ensure that the mount remains plumb and level.
4. Repeat this step for each mount horizontally
5. To install multiple rows, place spacer between previously installed
LMVSP’s on the bottom row. Make sure the spacer is plumb and level,
mark the corners (or secure to the wall) to be sure of where the LMVSP
should be and secure your mount to the wall.
Page 6
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
1) Insert a small straw or toothpick into the threaded
inserts found on the back of the at-panel.
2) Use a pencil to mark the depth of the threaded
insert on the small straw or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of
the threaded insert, as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth
using the straw or toothpick’s 1/8” allowance mark.
5) Locate the correct diameter screw for the threaded
insert.
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick,
as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the
mark.
6) Test each size of the screws provided.
The correct screws should thread easily into the
mounting point and not pull out when tension is
applied.
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
Optional adapters are available with your LMVSP mount.
Secure the adapters to the LMVSP brackets with the supplied
(4) M8 washers and (4) M8 nuts.
TOP
BOTTOM
TOP
BOTTOM
Selecting the Mounting Hardware
Securing the Adapters
Page 7
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
M8
M6
M4
Premier Mounts’ Universal Washers are designed to
accommodate the various M4, M6, and M8 hole sizes
required by at-panels.
Do not place excessive pressure on the back of the
at-panel, as this may damage your at-panel.
The Universal Washer must be installed between
the head of the mounting screw and the mounting
bracket as shown.
Premier Mounts’ Universal Spacers allow you to attach the mounting
bracket to at-panels which have recessed or uneven mount points. Each
Universal Spacer adds 1/4” to the distance between the mounting bracket
and your at-panel.
The Universal Spacers must be stacked and oriented as shown.
The Universal Spacers must only be installed between the
mounting bracket and your at-panel.
Flat Panel
Universal Washer
Universal Spacer
Mounting Bracket
Mount Point
Mounting Screw
Universal Washer Installation
Universal Spacer Installation
Page 8
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
Attaching the Mounting Brackets to the Flat-Panel
1) Secure each mounting bracket to your at-panel by inserting
a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Make sure the directional arrows on the mounting
brackets are facing up.
Mounting bracket adjustments are factory pre-set (see Note).
This section requires two people.
Do not release your at-panel until you are certain that top and
bottom hooks of both mounting brackets are securely seated
on the upper and lower mounting rails of the wall panel.
1) Raise the at-panel past the top and bottom mounting rails on the
wall panel.
2) Slide the at-panel down slowly, keeping it close to the wall.
3) Engage the top and bottom mounting brackets to the rails of the
mount.
Note: These registers must
align prior to installation.
They are factory set.
Check to determine proper
alignment
Attaching the Flat-Panel to the Mount
2) Before tightening the screws, push the bracket up to
remove slack from the bracket, then tightened the
screw.
NOTE: For smaller vesa bolt patterns, reverse the
mounting brackets.
Page 9
www.mounts.com | North America 800.368.9700 | International +1-714-632-7100
Installation Guide
LMVSP
The locking safety screws keep the at-panel from being
accidently dislodged from the LMVSP.
1) Locate the pre-installed security locking safety screw at the bottom
of each of the mounting brackets.
2) Use the M5 Allen driver (supplied) to tighten the locking safety
screw.
Pre-installed
Locking Safety Screw
(1 per Bracket)
Locking Safety Screw Installation
Post-Installation Adjustments
The LMVSP has a set of post-installation adjustments on each mounting
bracket (Figure 1).
Use the M5 Allen Driver (supplied) to ne-tune adjust.
Make sure the the locking safety screws are loosened before making
adjustments.
Figure 1
Note: Screws have a limited travel adjustment.
Do not overtighten or over adjust the screw to avoid damage to
threaded holes.
See Note
See Note
See Note
Do not overtighten the locking safety screws.
Note: Tighten screw to surface, then tighten 1/4” turn
Page 10
Other manuals for LMVSP
1
Table of contents
Other Premier Mounts Rack & Stand manuals
Premier Mounts
Premier Mounts PP-6 User manual
Premier Mounts
Premier Mounts ECM-3763T User manual
Premier Mounts
Premier Mounts ECM-3763S User manual
Premier Mounts
Premier Mounts Cathedral Ceiling Adapter PP-TL User manual
Premier Mounts
Premier Mounts LPSA3747 User manual
Premier Mounts
Premier Mounts Nesting Cart Series User manual
Premier Mounts
Premier Mounts CONVERGENT SAM-IFJ Series User manual
Premier Mounts
Premier Mounts UMB-DBTS User manual
Premier Mounts
Premier Mounts PTM User manual
Premier Mounts
Premier Mounts PSD-SPA User manual
Premier Mounts
Premier Mounts CTM-MS2 User manual
Premier Mounts
Premier Mounts CTM-MS2 User manual
Premier Mounts
Premier Mounts AM225 User manual
Premier Mounts
Premier Mounts AM175 User manual
Premier Mounts
Premier Mounts PRF User manual
Premier Mounts
Premier Mounts PBC- UMW User manual
Premier Mounts
Premier Mounts INW-AM200 User manual
Premier Mounts
Premier Mounts PBL-200 User manual
Premier Mounts
Premier Mounts Convergent A-A27 Series User manual
Premier Mounts
Premier Mounts AM80 User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
