Philips Streamium WACS700 Quick start guide

1. Introduction

The Firmware Upgrade will upgrade WAC700 & WACS700’s firmware to

Version 1.2.10.

__________________________________________________________________

2. Key features added

The software release 1.2.10 has provided a solution for CD ejection problem that

has happened on a marginal number of CDs.

__________________________________________________________________

3. Preparation

i) Verifying firmware version

Before upgrading, check the firmware version.

1. Turn on your WAC700 Center

2. Press MENU

3. Press ▲/▼to select “Information”. Press OK

→The display shows the FW (firmware) version number

→Upgrading is necessary if the FW version is an earlier one

Note: The firmware information is also useful when you call Philips Customer

Care Center.

ii) Checking Wi-Fi connection

Wi-Fi connection between Center and Station:

- Check you have pressed STANDBY-ON to turn on WAC700 Center and

WAS700 Station

- On Station, check you can playback tracks in HD mode

- On Station, check the signal indication shows maximum reception

Wi-Fi connection with the Wireless router/Access Point (if applicable):

- Check the Wireless router/Access Point is working if your Center

is connected to PC via a Wireless router/Access Point

__________________________________________________________________

4. Upgrading

You can upgrade the embedded firmware in 2 ways

A) Upgrading from CD-ROM

B) Upgrading from PC

A) Upgrading from CD-ROM

i) Prepare an upgrading CD

1. Check you have the following tools:

• PC (Pentium III 300MHz processor or higher)

• CD-R/RW writer and writing application software

• Blank CD-R or CD-RW disc

• Internet access (broadband or high speed)

2. Click the link to download Firmware Upgrade to your PC

3. Unzip the .zip file

(Note: - Do not rename the filename.

-Visit http://www.winzip.com/ for downloads if you can not

open the .zip file. )

4. Write the extracted files – not the zip file – onto a blank CD-R or CD-RW

disc, using the following settings:

• File System CD-ROM Joliet

• File name length : max 31 chars (ISO Level 2)

• Mode : 2/XA

• Character set : ASCII

• Single session

• Write Speed : Low

• Finalized the disc. (The application may do this automatically.)

(Note: Make sure you finalize the CD)

ii) Upgrade WACS700

Upgrade WAC700 Center:

1. Check WAC700 Center is on and WAS700 Station is off

2. On Center, insert the upgrading CD into the CD slot loader, with

CD graphic printed side facing you

→Upgrading starts automatically

→The display shows “Updating firmware, please wait……” .

A progress bar appears

→Center will reboot itself twice during the upgrading process

→After about 5 minutes, Center returns to HD mode. The upgrading is

completed

(Note: - Keep your Center turned on during the upgrading.)

Upgrade WAS700 Station:

3. Press STANDBY-ON to turn WAS700 Station

→Upgrading starts automatically

→The display shows “Updating firmware, please wait……” .

A progress bar appears

→Station will reboot itself twice during the upgrading process

→After about 5 minutes, Station returns to HD mode. The upgrading is

completed

(Note: - Keep your Station turned on during the upgrading.)

Helpful hints:

- To check the firmware version, see Preparation: Verifying firmware

version.

- If you have any problem, see troubleshooting.

B) Upgrading from PC

i) Download Firmware Upgrade to your PC

1. Click the link to download Firmware Upgrade to your PC

2. Unzip the .zip file

(Note: - Do not rename the filename.

-Visit http://www.winzip.com/ for downloads if you can not

open the .zip file. )

ii) Upgrade WACS700

Upgrade WAC700 Center:

1. Connect your PC and WAC700 Center using the supplied Ethernet

cable

2. Launch the Digital Media Manager (DMM) on your PC

3. Select Preference →Player Firmware →Upgrade Firmware

4. Click Yes to start upgrading

5. Find the Firmware Upgrade file you stored in the PC. Click Open

→You will start transferring the file to WAC700 Center

→After file transferring is finished, upgrading starts automatically on

WAC700 Center

→The Center’s display shows “Updating firmware, please

wait……”. A progress bar appears

→Center will reboot itself twice during the upgrading process

→After about 5 minutes, Center returns to HD mode. The upgrading is

completed

(Note: - Keep your Center turned on during the upgrading.)

Upgrade WAS700 Station:

6. Press STANDBY-ON to turn on WAS700 Station

→Upgrading starts automatically

→The display shows “Updating firmware, please wait……” .

A progress bar appears

→Station will reboot itself twice during the upgrading process

→After about 5 minutes, Station returns to HD mode. The upgrading is

completed

(Note: - Keep your Station turned on during the upgrading.)

Helpful hints:

- To check the firmware version, see Preparation: Verifying firmware

version.

- If you have any problem, see troubleshooting.

__________________________________________________________________

5. Troubleshooting

If the Station’s display shows: "Firmware is damaged, restoring a new copy …"

or "Center is connected, retrieving firmware"

Follow the DON’T below:

a. DON’T restore Center’s setting (Don’t select "Menu" →"Setting"

→"Restore Setting" on Center)

b. DON’T delete Stations from Center (Don’t select "Menu" →

"Station Mgnt" →"Delete Station" on Center)

c. Do NOT change Center’s Wi-Fi setting

Then,

1. If the progress bar is moving on, wait and upgrading will start later on the

Station

2. If the progress bar stops moving and/or Station’s display shows "Error Code

xxx", turn off the Station and then turn it on.

3. If Step 2’s problem still exists, check there is no Wi-Fi interference around and

reduce the distance between Center, Station and Wireless router/Access Point

(if applicable)

__________________________________________________________________

6. Firmware history

Version 1.2.10

• The software release 1.2.10 has provided a solution for CD ejection problem

that has happened on a marginal number of CDs.

Version 1.2.6

• The software release 1.2.6 has improved certain software stability of WAC700.

Version 1.1.17

• Improved the CD slot loader mechanism to be more robust during insertion and

ejection.

Version 1.1.15

• Improved Wi-Fi connection, shorten the connection time.

• Improved the CD slot loader mechanism to be more robust during insertion and

ejection.

Version 1.1.10

• Firmware released later than the Version 1.0. Version 1.1.10 provides more

stable Wi-Fi streaming for MP3 tracks

Note: If power failure occurs during CD ripping, you will lose all the tracks not

compressed yet.

Version 1.0

• Firmware installed on the set delivered

Other manuals for Streamium WACS700

This manual suits for next models

Other Philips Stereo System manuals

Popular Stereo System manuals by other brands

LG CM3330B owner's manual

Sony

Sony SS-CEP50 Service manual

Cetacea Sound

Cetacea Sound CVS-II user guide

Aiwa

Aiwa XR-H66MD operating instructions

Denon

Denon UCD-250 Service manual

Sanyo

Sanyo DC-MX41i instruction manual

Sharp

Sharp CD-ES600V Service manual

Exibel

Exibel BDX600-UK user manual

Sanyo

Sanyo DC-F320 Service manual

Sharp

Sharp CD-C462 Service manual

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio instruction manual

Aiwa

Aiwa XR-EM70 Service manual

Cyrus

Cyrus Lyric user guide

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C owner's manual

RCA

RCA RS3965SB user manual

Sharp

Sharp XL-UH240 Operation manual

LG FB165DAB Service manual

Sanyo

Sanyo DC-UB1475M/XE/UK Service manual