PEERLESS SR1G Guide
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
Installation and Assembly: 32" - 60" Flat Panel TV Cart
Models: SR1G, SR560G
Max UL Load Capacity:
150 lb (68 kg) screen
50 lb (22.7 kg) per shelf
This product is UL Listed. It must be
installed by a qualified professional
installer.
R
2 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List..........................................................................................................................................................................3, 4
AssemblingCart ...................................................................................................................................................................5
AttachingUniversalAdapterPlateorDedicatedAdapterPlate................................................................................................10
InstallingAdapterBrackets.................................................................................................................................................11
CordManagement................................................................................................................................................................13
Tools Needed for Assembly
•level
•phillipsscrewdriver
• Donot begin toinstall your Peerlessproduct until youhave read andunderstood the instructionsand warnings
containedin this InstallationSheet. If youhave any questionsregarding any ofthe instructions orwarnings, please
callPeerlesscustomer care at 1-800-729-0307.
• Thisproduct should onlybeinstalled by someoneof good mechanical aptitude,and fully understands
these instructions.
• Neverexceed the Maximum ULLoad Capacity on page1.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screwsfirmly, but donotovertighten. Overtightening can damagetheitems, greatly reducing theirholding
power.
• The cart is not affixed or secured to the floor, and may therefore tip over and/or fall if screen and/or stand is shaken
or hit.Always monitor children and do not let children play alone around stand as they could get hurt by a falling
screen.Not recommended for use inareas with heavytraffic.
WARNING
3 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
SR1G SR560G
Black Black
Description Qty. Part Number Part Number
Ascreen mount bracket 1 201-1156 201-1156
Bhook plate 1 201-1157 201-1157
Cshelf support 1 201-1158 201-1158
Dshelf clamp bracket 1 201-1159 201-1159
Ebase 1 009-1223 009-1223
Funiversal plate 1 N/A 201-1110
Gadapter bracket 2 N/A 201-1510
Hupright 1 580-1180 580-1180
Iglass shelf 1 590-1208 590-1208
Jtop cover 1 590-1210 590-1210
Kbutton bumper 9 590-1209 590-1209
L1/4-20 x 12 mm decorative screw 14 520-2325 520-2325
M1/4-20 nut 12 530-1022 530-1022
N5/16" flat washer 10 540-9406 540-9406
O3/8-16 x 2.5" socket screw 3 520-9550 520-9550
P7/32" allen wrench 1 560-9715 560-9715
Q4 mm allen wrench 1 560-9646 560-9646
R6 mm allen wrench 1 560-9716 560-9716
Sleft leg 1 009-0220 009-0220
Tright leg 1 009-0218 009-0218
Uwheel caster 2 600-0044 600-0044
Vwheel caster/brake 2 600-0045 600-0045
Wjoint connector nut 4 530-1037 530-1037
X3/8-16 x 1.5" screw bolt 4 520-1329 520-1329
YM10 x .402 ID washer 3 540-9424 540-9424
Zend cap 4 590-1032 590-1032
AA 1/4-20 x 20 mm screw 2 520-2326 520-2326
BB 3/16 allen wrench 1 560-0071 560-0071
CC M4 x 12 mm serrated washer head socket pin screw 6 N/A 510-1079
DD M4 x 25 mm serrated washer head socket pin screw 4 N/A 510-1082
EE M5 x 12 mm socket pin screw 4 N/A 520-1064
FF M5 x 25 mm socket pin screw 4 N/A 520-1122
GG M6 x 12 mm socket pin screw 4 N/A 520-1050
HH M6 x 25 mm socket pin screw 4 N/A 520-1211
II M8 x 15 mm socket pin screw 6 N/A 520-1068
JJ M8 x 40 mm socket pin screw 4 N/A 520-1152
KK .219 ID x .5 OD x .5 HT spacer 4 N/A 540-1057
LL .344 ID x .75 OD x .5 HTspacer 4 N/A 540-1059
MM multi-washer 6 N/A 580-1036
NN M6 x 20 mm socket pin screw 4 N/A 520-9554
OO M6 x 30 mm socket pin screw 4 N/A 520-1067
PP M8 x 25 mm socket pin screw 4 N/A 520-1101
QQ M10 x 15 mm socket screw 4 520-9262 520-9262
Parts List
4 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
OO
V
U
RQ
II
Some parts may appear slightly different than illustrated.
BB
H
E
ABC
WZ
J
Y
P
X
O
QQ
L NM
G
CC DD EE JJFF HH
GG
MM
LL
KK NN PP F
Parts List continued
Universal Adapter Plate, Brackets and Hardware included with model SR560G only
D
KI
AA
S
T
5 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
1Insert four end caps (Z) into ends of left and right support legs (S & T)as shown.
Z
S
T
Guide right leg (T) towards base housing (E) as shown in fig.2.1. Then line up holes in base housing with holes i right
leg. Fasten base housing to right leg using two 3/8-16 x 1.5" screw bolts (X) and two joint connectors (W), tighten
using 3/16"allen wrench (BB) and 7/32"allen wrench (P) as shown in fig.2.2. Repeat for left side with left leg (S).
2
T
X
fig. 2.2
W
fig. 2.1
E
T
6 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
3Insert and screw casters (V &U) into holes of support legs (S &T). Attach casters with brake (V)to the back of left
and right support legs (S &T). Attach casters without brake (U)to front of support legs (S &T) as shown.
NOTE:Lockbrakesoncasters,fornosudden movements during installation.
S
VU
T
HANDTHREAD
HOLDWHEEL
Attach upright (H) to base (E), as shown in fig 4.2 using three 3/8-16 x 2.5" socket screws (O) and M10 x .402ID
lock washers (Y). Tighten screws using 7/32" allen wrench (P) shown in fig. 4.1.
4
fig. 4.1
E
O
H
Y
fig. 4.2
CORDMANAGEMENT
HOLES
7 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
SLOT
fig 6
C
Loosely attach four 1/4-20 x 12 mm screws (L), washers (N), and 1/4-20 nuts (M) to shelf support (C).
5
Slide shelf support (C)onto upright (H) so that 1/4-20 nuts (M) slide into slots of upright (H) as shown in figure
6 and detail 1. Slide shelf support to desired position, level, then tighten 1/4-20 x 12 mm screws (L) using 4
mmallen wrench (Q).
NOTE: MAXIMUMOFTWO SHELVES
Max height of top shelf is 34" from base.
Max height of second shelf is 28" from base.
M
H
DETAIL 1
C
L
NM
6
8 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
Insert three button bumpers (K) into bottom of shelf clamp bracket (D).
Attach shelf clamp bracket (D) to shelf support (C) using two 1/4-20 x 20 mm screws (AA) and two
1/4-20nuts (M).
For additional shelf installation, repeat steps 5 through 7.
Insert six button bumpers (K) into shelf support (C). Place glass shelf (I) on shelf support.
I
K
C
7
7-1
K
7A
7-2
Attaching Glass Shelf
D
C
AA
M
• Do not overtighten, may cause glass to shatter or
crack.
WARNING
9 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
Insert two 1/4-20 x 12 mm screws (L) into screen
mountbracket (A), leaving 3/16" ofexposed thread
as shown in figure 11 and detail 3.
J
H
Snaptop cover (J)ontoupright (H). 11
10
3/16"
fig. 11
DETAIL 3
L
A
Loosely attach six 1/4-20 x 12 mm screws (L),
washers (N), and 1/4-20 nuts (M) to screen mount
bracket(A).
8Slide screen mount bracket (A) onto upright (H) so
that 1/4-20 nuts (M) slide into slots of upright (H) as
shown in figure 9 and detail 2. Slide screen mount
bracket to desired position, level, then tighten 1/4-20
x 12 mm screws (L) using 4 mm allen wrench (Q).
9
LNA
MA
H
SLOT
fig. 9
L
DETAIL 2
M
H
10 of 13 ISSUED: 01-10-07 SHEET #: 009-9033-5 04-16-08
NOTE:Refer to instructions included with
Dedicated Adapter Plate for assembly to screen.
Once attached, proceed to step 12.
AttachUniversalPlate (F) orDedicatedAdapter
Plate to hook plate (B) using four M10 x 15 mm
socket screws (QQ). Tighten screws using 6 mm
allenwrench(R).
Attaching Universal Adapter Plate or Dedicated Adapter Plate
13 Attach hook plate (B) to screen mount bracket (A).
B
A
L
LL
2° Backward Tilt 5° Forward TiltNo Tilt
B
UNIVERSALPLATE
OR
DEDICATEDADAPTERPLATE
(SOLDSEPARATELY)
14 Insert two 1/4-20 x 12 mm screws (L) into holes indicated below for desired screen orientation. Tighten all screws
using 4 mm allen wrench (Q).
F
B
UNIVERSAL
PLATE
SHOWN
12
QQ
QQ
Other manuals for SR1G
2
This manual suits for next models
1
Table of contents
Other PEERLESS Rack & Stand manuals
PEERLESS
PEERLESS MIS488 Guide
PEERLESS
PEERLESS Vision Point LCFS 100 Guide
PEERLESS
PEERLESS Paramount PSP2 Guide
PEERLESS
PEERLESS LCC 18 Guide
PEERLESS
PEERLESS SmartMount D-FPF-320 Guide
PEERLESS
PEERLESS PARAMOUNT PF640 Guide
PEERLESS
PEERLESS COL 510P Guide
PEERLESS
PEERLESS LWB375 Guide
PEERLESS
PEERLESS Mobile Videowall Trolley PDVWM 2x2 46 55 L Guide
PEERLESS
PEERLESS SMARTMOUNT SCS221 Guide
PEERLESS
PEERLESS HCACC502 User manual
PEERLESS
PEERLESS HCW101 User manual
PEERLESS
PEERLESS CMJ450 Guide
PEERLESS
PEERLESS Paramount PP730 and assembly Guide
PEERLESS
PEERLESS IWB600-WB User manual
PEERLESS
PEERLESS PLCM 3 Guide
PEERLESS
PEERLESS SF630-AB Guide
PEERLESS
PEERLESS Solid-Point PLCM 2 Guide
PEERLESS
PEERLESS AEC0609 Guide
PEERLESS
PEERLESS ESA746PU Guide
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
