PEERLESS SmartMount SP740P Guide

Max UL Load Capacity: 80 lb (36.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Installation and Assembly:

SmartMount™ Pivot Wall Arm for LCD Screens

Models: SP740P, SP740P-S

Features:

•Fits 22" - 40" LCD screens

• Twotensionablepivot pointsfor extensiveadjustment ofviewing angle

• VESA®75/100/200 x 100/200 x 200 compatible

• Frees up space by folding flat against the wall

2 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Note: Read entire instruction sheet before you start installation and assembly.

Forcustomer care call(800) 865-2112or (708) 865-8870.

Table of Contents

Parts List.............................................................................................................................................................................. 3

Installation to Wood Stud Wall ............................................................................................................................................. 4

InstallationtoSolid Concreteand Cinder Block .................................................................................................................... 5

Tools Needed for Assembly

• studfinder("edge toedge"stud finderisrecommended)

• phillipsscrewdriver

• 3/16"allen wrench

• drill with 1/4" and 5/32" drill bits

Accessories

• Metal Stud Wall Plate (WSP490) – required to attach mount to metal studs (Not evaluated by UL)

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call

Peerlesscustomer careat 1-800-865-2112.

• Thisproduct should onlybe installedby aqualified professional.

• Makesurethat thesupportingsurface willsafely support thecombined load ofthe equipment andall attached hard-

wareand components.

• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25

gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless Metal Stud Wall Plate

(WSP 490) for metal studs.

• Neverexceed theMaximum ULLoadCapacity.

• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the

studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

WARNING

3 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

CFG

SP740P SP740P-S

Description Qty. Part # Part #

Awall mount assembly 1 095-0375 095-0377

BAlligator® anchor 2 590-0097 590-0097

.198" ID x .313" OD x .437" H retaining spacer

4 590-5005 590-5003

D1/4-20 x 1/2" flat head phillips screw 2 520-1209 520-2178

EM4 x .7 x 10 mm phillips screw 4 504-9012 520-2027

FM4 x .7 x 20 mm phillips screw 4 504-9020 504-2014

GM6 x 1 x 12 mm phillips screw 4 520-1128 520-2039

H#14 x 2-1/2" flat head wood screw 2 520-1202 520-2165

IM6 x 1 x 20 mm phillips screw 4 520-9402 520-2040

JM6 x 1 x 30 mm phillips screw 4 510-9109 520-2042

KM5 x 1 x 6 mm phillips screw 5 520-1023 520-2214

L#10 flat washer 4 540-9400 540-9442

Mhook bracket 1 095-1346 095-4346

Nadapter plate 1 095-1322 095-4322

O#10-32 x 1/4" flat head phillips screw 1 520-1108 520-2108

Parts List

4 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Installation to Wood Stud Wall

Using a stud finder, locate and mark the edges of the wood stud used in mounting this product. Use of an edge to

edge stud finder is highly recommended. Use a level to draw a vertical line down the center of the stud. Use wall

plate as template to mark center of holes along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm)

deep.Attach wall mount (A) to wall using two #14 x 2.5" flat head wood screws (H) as shown.

Skip to step 2 on page 6.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareand components.

WARNING

WOOD

STUD

WALL

WALLPLATE

• Tightenscrewsso thatwallplate isfirmly attached, butdo not overtighten.Overtightening can damagethe screws,

greatlyreducing theirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highlyrecommended.

WARNING

5 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

• Concrete anchors are notintended forattachment to

concretewall coveredwitha layerof plaster, drywall,

orother finishingmaterial asshown below. Ifmounting

toconcrete wallcoveredwith plaster/drywallis

unavoidable,plaster/drywall (up to5/8" thick)must be

counterboredas shownbelow.Be sureconcrete

anchorsdo notpullaway fromconcrete whentighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer

(notULevaluated).

WARNING

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingout the backof thehole when enteringa voidor cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardwareand components.

WARNING

Level and use wall plate as template to mark

center of holes. Drill two 1/4" (6 mm) dia. holes to

a minimum depth of 2.5" (64 mm). Insert anchors

(B) in holes flush with wall as shown in fig 1.1.

Place wall mount (A) over anchors and secure with

wood screws (H) as shown in figures 1.2 and 1.4.

Make sure wall mount is level, and tighten all

fasteners. See figure 1.3.

concrete

wall

Drill holes

and insert

anchors.

Place wall

plate over

anchor and

secure with

screw.

Tighten all

fasteners.

WALLPLATE

fig. 1.1

fig. 1.2

fig. 1.3

CUTAWAYVIEW

CORRECT

concrete

plaster/

drywall

INCORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is firmly attached,

butdo notovertighten.Overtighteningcandamage the

screws,greatly reducingtheir holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

fig. 1.4

WALLPLATE

6 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Attaching Adapter Plate to Screen with VESA 200 x 100 or 200 x 200 Mounting

Pattern

Attach hook bracket (M) to adapter plate (N) using

four M5 x 6 mm screws (K) and #10 washers (L) as

shown.

FORVESA200x100MOUNTINGPATTERN:

Chooseholepattern asshownbelow. Attachadapter

plate (N) to back of screen using four M4 x 10 mm

screws(E)asshownbelow.

*Note: If screw (E) gets less than three threads of

engagement, attach adapterplate (N)tobackof

screen using four M4 x 20 mm screws (F) and four

spacers(C) asindicated below.

Skip to step 3 on page 9.

FORVESA200x200MOUNTINGPATTERN:

Chooseholepattern asshownbelow. Attachadapter

plate (N) to back of screen using four M6 x 12 mm

screws(G) asshown below.

*Note: If screw (G) gets less than three threads of

engagement, attach adapterplate (N)tobackof

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 3 on page 9.

*For screens with a hole

pattern in a pocket,

spacers (C) go between

adapter plate (N) and

screen.

Note: For VESA 75 mm and 100 mm patterns, see

followingpage.

2-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

7 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern

*For screens with a hole

pattern in a pocket,

spacers (C) go between

hook bracket (M) and

screen.

FORVESA®75MOUNTINGPATTERN:

Chooseholepattern asshown below. Attachhook

bracket (M) to back of screen using four M4 x 10 mm

screws(E)asshownbelow.

*Note: If hole pattern is in a pocket, attach hook

bracket (M) to back of screen using four M4 x 20 mm

screws(F) andfour retainingspacers(C)asindicated

below.

FORVESA100MOUNTINGPATTERN:

Chooseholepattern asshown below. Attachhook

bracket (M) to back of screen using four M4 x 10 mm

screws(E)asshownbelow.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

8 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

GENERICADAPTER

BRACKET

FOR INSTALLING TO PEERLESS LC MODEL ADAPTER BRACKET

For screen compatibility please refer to the LCD or plasma interface list on our website www.peerlessmounts.com or

call customer care for a screen specific adapter bracket LC or PLP models (not UL evaluated).

FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET

GENERICADAPTER

BRACKET

M5 X 6 MM OR M5 X 10 MM SCREW

M5X 10 MMSCREW

Note: Referto LC modeladapter bracketinstructionsheet forattachment ofadapterbracket toscreen.

Note: Either M5 x 6 mm or M5 x 10 mm screws are included with the LC model adapter bracket.

Attach hook bracket (M) to adapter bracket using four M5 x 6 mm or M5 x 10 mm screws.

Note: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.

Note: M5 x 10 mm screws are included with the PLP model adapter bracket

Attach hook bracket (M) to adapter bracket using four M5 x 10 mm screws.

9 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

Adjust tension knob on side of mount shown in figure

4.1 to desired tension to balance your screen size

andweight.

Push or pull from top or bottom of screen to adjust

tilt as shown. The tilt can be adjusted to a maximum

of15° forwardor 5°backward.

• Becareful notto pinchfingerswhen openingand

closing mount from the wall.

CAUTION

• Do not tighten screws with excessive force.

Overtighteningcan causedamage tomount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

TENSIONKNOB

fig. 4.1

4-1 Roll screen to desired position (5° clockwise or

counter-clockwise).Insert#10-32 x1/2"flat head

phillips screw (O) to lock screen into position as

shownin figure 4.2.

fig. 4.2

To attach screen to wall mount (A), lower hook

bracket (M) with screen at an angle into pockets of

wall mount as shown in figure 3.1. Once clips are

engaged, push down to seat clips in pockets as

shown in figure 3.2. Insert and tighten M5 phillips

screw (K) to lock screen to wall mount as shown in

figure3.3.

Toremove screenfrom mount,loosenscrew (K)and

lift screen off of mount.

Installing and Removing Flat Panel Screen

SCREEN

fig. 3.1 fig. 3.2

fig. 3.3

• Do not tighten screws with excessive force.

Overtighteningcan causedamage tomount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

• Do not lift more weight than you can handle. Use

additionalman poweror mechanicallifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket (M) with screw (K) can

cause screen to come off mount if hit accidentally.

WARNING POCKET

CLIP

10 of 10 ISSUED: 05-18-05 SHEET #: 095-9235-7 02-22-07

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn tension screw(s) clockwise with allen wrench.

• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench. Do not turn more than half a turn.

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the

screen to fall.

WARNING

TENSIONSCREWS

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Other manuals for SmartMount SP740P

This manual suits for next models

Other PEERLESS Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 