Paradyne FrameSaver DSL 9788 Router User manual

FrameSaver®DSL 9788 Router

Installation Instructions

Document Number 9788-A2-GN11-00

July 2002

Contents

FrameSaver DSL Router Overview ............................................................... 2

Upgrading a Unit to Advanced SLM Feature Set .......................................... 3

Product Documentation Online ..................................................................... 3

Package Checklist ......................................................................................... 4

Wiring and Cables You May Need ................................................................ 5

Provisioning Data Circuits Before Installation ............................................... 6

Installing the Router ...................................................................................... 7

Power-On ...................................................................................................... 11

Status LEDs .................................................................................................. 12

Troubleshooting ............................................................................................. 13

Configuration Setup ...................................................................................... 14

Verifying that Self-Test Passed ..................................................................... 17

Using the Easy Install Feature ...................................................................... 17

Completing Setup From the NOC ................................................................. 18

Setting Up for In-Band Management ............................................................ 19

Provisioning the Router Interface .................................................................. 22

Cables and Connectors ................................................................................ 22

Router Technical Specifications .................................................................... 25

Important Safety Instructions ........................................................................ 26

Government Requirements ........................................................................... 27

Warranty, Sales, Service, and Training Information ...................................... 28

FrameSaver DSL Router Overview

The FrameSaver®DSL (Digital Subscriber Line) Router is a component in the

FrameSaver system. This system allows you to perform end-to-end service level

management (SLM) across a hybrid DSL/ATM/Frame Relay network. Service providers

can isolate and correct problems remotely from their NOC (Network Operations Center).

The router has a DSL interface and is a manageable frame relay-aware endpoint. It

operates as a bridge or an IP router that connects a DSL link to an Ethernet network.

The FrameSaver DSL Router is used for data only and provides corporate LAN access

over traditional twisted-pair copper telephone wiring. Copper pairs run from the central

office (CO) to the customer premises (CP) to create the local loop. The local loop

terminates on the customer premises at the demarcation point in a punchdown block or

network interface device (NID). The following diagram shows a typical use of the

FrameSaver DSL Router in a network.

DSL

Access

Network

00-16915a

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

24681012141618

1357911131517

LAN/WANSLOT

CLOCKB

SERIAL

MCCAC

ALARM

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

ATM

Switches

Hotwire

GranDSLAMs

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

24681012141618

1357911131517

LAN/WANSLOT

CLOCKB

SERIAL

MCCAC

ALARM

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

TDM

Access

Network

LAN

FR Network

FR/ATM

IWF

ATM

Switches FR

Switches

Frame Relay NSP's Network

ATM

NNI(s)

Aggregation

Switch

(Optional)

Copper

Loop

DSL

FrameSaver

DSL 9783

Bridge/Router

Endpoint

Customer

Premises–

Remote Site

Router

FrameSaver

Endpoint

Customer Premises–

HQ Site

Central Office

ATM

Services LAN

ATM –Asynchronous Transfer Mode

DSL –Digital Subscriber Line

FR –Frame Relay

HQ –Headquarters

IWF –Interworking Function

LAN –Local Area Network

NSP –Network Service Provider

TDM –Time Division Multiplexer

The FrameSaver DSL Router is available in two feature sets:



Diagnostic Feature Set provides basic frame relay and diagnostic capability.



Advanced SLM (Service Level Management) Feature Set provides the same

features as the Diagnostic Feature Set, plus service level management and

reporting capability.

Refer to

About FrameSaver DSL Devices

in the User’s Guide for a list of FrameSaver

DSL router’s features, and the capabilities provided by each feature set.

Upgrading a Unit to Advanced SLM Feature Set

A FrameSaver DSL Router with the Diagnostic Feature Set can be upgraded to the

Advanced SLM Feature Set at any time by ordering a FrameSaver Advanced SLM

Activation Certificate (Feature Number 9788-C1-220). A certificate can be ordered for a

single DSL router, or for many DSL routers. You must specify the model to be activated

(for example, 9788-Rtr), your OpenLane SLM system license key number, and the

number of router activations to be included on the certificate.

The OpenLane®SLM system, Release 5.3 or later, is required toschedulethe activation

of Advanced SLM features and to manage the certificate activations included in the

certificate.

To learn more about activating the Advanced SLM Feature Set, refer to the

FrameSaver

SLV Activation Instructions

(Document Number 9000-A2-GK43), or contact your sales

representative.

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.

Select

Library

→

Technical Manuals

→

FrameSaver Frame Relay Devices.

Select the following document:

9700-A2-GB20

FrameSaver DSL, Models 9783 and 9788,

User’s Guide

To order a paper copy of a Paradyne document:



Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)



Outside the U.S.A., call 1-727-530-8623

Package Checklist

In addition to these instructions, verify that your package contains the following:

❑FrameSaver DSL Router

❑Power cord with power transformer

❑Tie wrap for power cord strain relief

❑DSL network access cable (with U.S. models only)

❑

FrameSaver DSL Router, Models 9783 and 9788, Quick Reference

(Document

Number 9700-A2-GL11)

Be sure to register your warranty at www.paradyne.com/warranty.

Wiring and Cables You May Need

The following wiring and cables are used with this product, which uses standard

interface connectors:



Standard connectors: An 8-pin modular (similar to RJ45) wall jack for the DSL

network connection.



DSL wiring: Unshielded twisted-pair wiring (CAT3, or better). The CAT3 wiring must

meet EIA/TIA-568 specifications with 24 AWG (0.5 mm) or 26 AWG (0.4 mm).



Ethernet wiring: Shielded twisted-pair wiring (CAT5, or better). The CAT5 wiring

must meet EIA/TIA-568 specifications with 24 AWG (0.5 mm) or 26 AWG (0.4 mm).

For standard cables, refer to

Cables and Connectors

on page 22 for standard pin

numbers. For Paradyne cables, contact your sales representative to order them.

Interface

Connection Cables Feature

Number

COM

Communication

port to a PC or

asynchronous

terminal

DB9-to-DB9, standard EIA-232

straight-through cable —

ETHERNET

Ethernet port to a

NIC on a PC or an

Ethernet hub

For connection to a PC NIC:

Standard Ethernet crossover cable 9008-F1-550

For connection to an Ethernet Hub:

Standard Ethernet straight-through cable —

NET

Networkporttothe

DSL wall jack

Standard straight-through DSL network cable

with 8-pin modular connectors, similar to an

RJ45-to-RJ45 cable. Supplied with U.S.

models.

3100-F1-500

Provisioning Data Circuits Before Installation

Before installing the router, use the OpenLane SLM system’s Provision Circuit screen to

add:



New circuits that start at the FrameSaver DSL endpoint and traverse the SCM and

ATM line card in the Hotwire®GranDSLAM™



The default VC sets (from 1 to 4)

A group of 250 VCs can be allocated to each line card, which can be assigned to any

port on the card. These custom connections carry the frame relay traffic.

Note that before the custom cross-connections are configured, the Maximum VCI

number for the uplink VP to be used by these custom connections must be specified on

the Max VCI per VPI screen, and the apply changes executed.

For ATM line cards, custom connections can be used to expand the number of VCs

connected to the card. Each of the 250 VCs can be cross-connected from anyVC on the

uplink to any port on the line card.

The following information is collected by the Provision Circuit process:



Uplink VPI/VCI



Slot number and Port number of the DSL connection



Traffic Profile



DSL link VPI/VCI



Frame relay DLCI (provided by NSP)



Frame relay CIR, Be, Bc(provided by NSP)

A Circuit ID is then applied to the newly defined circuit, and stored in both the router and

the OpenLane SLM system.

Installing the Router

Place the FrameSaver DSL Router on a flat surface, with clearance for the rear

connectors.

Procedure

1. Use an 8-pin modular cable (supplied with U.S. models).

Insert one end of the cable into the jack labeled NET. Insert the other end into the

wall jack for DSL data communications.

ETHERNET

POWER NET

COM

NET

01-16981

DSL

Network

2. Use an 8-pin Ethernet cablefor the Ethernet connection. Insert one endof the cable

into the jack labeled ETHERNET.

—Use a straight-through cable to connect the other end of the cable to an

Ethernet hub. Do not connect to the hub’s optional Uplink connection with a

straight-through cable; the Uplink connection requires an Ethernet crossover

cable.

–or –

—Use an Ethernet crossover cable to connect to a PC with an Ethernet Network

Interface Card (NIC) installed or a hub’s Uplink connection.

01-16982

Ethernet

Straight-Through

Cable

ETHERNET

POWER NET

COM

Hub

3. Use a VT100-compatible asynchronous terminal or PC to set up management

access to the unit. Insert the DB9 end of an EIA-232 cable into the router’s COM

port. Tighten the screws on each side of the connector. Insert the other end into the

terminal or PC.

The terminal or PC’s configuration must becompatible with the router’s. Refer to the

procedure on page 15 of

Configuration Setup

. If connecting an external modem to

the COM port, refer to

Connecting an External Modem

on page 24.

ETHERNET

POWER NET

COM

01-16983

4. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the

transformer into an AC outlet.

Install the supplied tie wrap for strain relief, as shown.

Installation of the hardware is now complete. When the power cord is installed, the

router goes through a power-on self-test.

ETHERNET

POWER NET

COM

01-16984

Grounded

Power

Outlet

Cable

Tie

POWER

This manual suits for next models

Table of contents

Other Paradyne Network Router manuals

Paradyne

Paradyne FrameSaver 9783 User manual

Paradyne

Paradyne Hotwire 6351 User manual

Paradyne

Paradyne Hotwire 6371 User manual

Paradyne

Paradyne Hotwire 7995 User manual

Paradyne

Paradyne Hotwire 6301 User manual

Paradyne

Paradyne FrameSaver 9783 User manual

Paradyne

Paradyne 6382 User manual

Paradyne

Paradyne Hotwire 6301 User manual

Paradyne

Paradyne FrameSaver FLEX 9623 User manual

Paradyne

Paradyne iMarc SLV 9126 User manual

Paradyne

Paradyne 1754 SHDSL Original operating instructions

Paradyne

Paradyne FrameSaver 9720 User manual

Paradyne

Paradyne Hotwire 6381 User manual

Paradyne

Paradyne Hotwire 6341 User manual

Paradyne

Paradyne Hotwire 6321 User manual

Paradyne

Paradyne FrameSaver SLV 9664 User manual

Paradyne

Paradyne 1740 SHDSL Original operating instructions

Paradyne

Paradyne 1740 SHDSL User manual

Paradyne

Paradyne 6211-I1 User manual

Paradyne

Paradyne Hotwire 6212 Original operating instructions

Paradyne

Paradyne FrameSaver 9123 User manual

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU User manual

Paradyne

Paradyne 1740 SHDSL User manual

Paradyne

Paradyne 6212-I1 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview