Paradyne FrameSaver 9783 User manual

FrameSaver®DSL 9783 Router

Installation Instructions

Document Number 9783-A2-GN11-10

April 2001

Contents

FrameSaver DSL 9783 Router Overview ...................................................... 1

Upgrading a Basic Unit to SLV ...................................................................... 3

Product Documentation Online ..................................................................... 3

Package Checklist ......................................................................................... 3

Wiring and Cables You May Need ................................................................ 4

Prior to Installing the Router ......................................................................... 5

Installing the Router ...................................................................................... 6

Status LEDs .................................................................................................. 10

Troubleshooting ............................................................................................. 11

Configuration Setup ...................................................................................... 12

Verifying that Self-Test Passed ..................................................................... 15

Using the Easy Install Feature ...................................................................... 15

Completing Setup From the NOC ................................................................. 16

Setting Up for In-Band Management ............................................................ 17

Provisioning the Router Interface .................................................................. 20

Cables and Connectors ................................................................................ 21

DSL Router Technical Specifications ............................................................ 24

Important Safety Instructions ........................................................................ 25

Government Requirements ........................................................................... 27

Warranty, Sales, Service, and Training Information ...................................... 28

FrameSaver DSL 9783 Router Overview

The FrameSaver®DSL (Digital Subscriber Line) 9783 Router is a component in the

FrameSaver system. This system allows you to perform end-to-end service level

management (SLM) across a hybrid FrameSaver DSL/ATM/Frame Relay network.

Service providers can isolate and correct problems remotely from their NOC (Network

Operations Center).

The router has an SDSL front end and is a manageable frame relay aware endpoint. It

operates as a bridge or an IP router that connects a DSL link to an Ethernet network.

The FrameSaver DSL 9783 Router is used for data only and provides corporate LAN

access over traditional twisted-pair copper telephone wiring. Copper pairs run from the

central office (CO) to the customer premises (CP) to create the local loop. The local loop

terminates on the customer premises at the demarcation point in a punchdown block or

network interface device (NID). A typical example of using the FrameSaver DSL 9783

Router in a network configuration is shown below.

The FrameSaver DSL 9783 Router is available in two feature sets:



Basic Feature Set 1 provides basic frame relay and diagnostic capability.



Advanced SLV (Service Level Verification) Feature Set 2 provides basic features,

plus SLV management and reporting capability.

DSL

Access

Network

00-16915a

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

24681012141618

1357911131517

LAN/WANSLOT

CLOCKB

SERIAL

MCCAC

ALARM

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

ATM

Switches

Hotwire

GranDSLAMs

ALARMS

MajorMinor

Fan

POWER

SERIAL

SMCM

CLOCK

ALARM

24681012141618

1357911131517

LAN/WANSLOT

CLOCKB

SERIAL

MCCAC

ALARM

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

48VRTN

48VNEG

POWERENTRYMODULE

LEFTUNIT:LINEA

RIGHTUNIT:LINEB

WARNING!

POWERMUSTBEDISCONNECTEDATTHESOURCE

BEFOREREMOVINGORINSTALLINGTHISPWRENTRYMODULE

TDM

Access

Network

LAN

FR Network

FR/ATM

IWF

ATM

Switches FR

Switches

Frame Relay NSP's Network

ATM

NNI(s)

Aggregation

Switch

(Optional)

Copper

Loop

DSL

FrameSaver

DSL 9783

Bridge/Router

Endpoint

Customer

Premises–

Remote Site

Router

FrameSaver

Endpoint

Customer Premises–

HQ Site

Central Office

ATM

Services LAN

ATM –Asynchronous Transfer Mode

DSL –Digital Subscriber Line

FR –Frame Relay

HQ –Headquarters

IWF –Interworking Function

LAN –Local Area Network

NSP –Network Service Provider

TDM –Time Division Multiplexer

Refer to

About FrameSaver DSL Devices

in the User’s Guide for a list of FrameSaver

DSL 9783 features, and the capabilities provided by each feature set.

Upgrading a Basic Unit to SLV

A basic FrameSaver DSL 9783 Router can be upgraded to full SLV capability at any time

by ordering a FrameSaver SLV Activation Certificate. A certificate can be ordered for a

single 9783 router, or for many 9783 routers. The OpenLane®SLM system, Release 5.3

or later, is required to schedule the activation of SLV features, and to manage the

certificate activations included in the certificate.

To upgrade a basic 9783 router to full SLV capability, order the FrameSaver SLV

Activation Certificate (Feature No. 9783-C1-220), providing the model to be activated

(i.e., 9783-Rtr), your OpenLane SLM system license key number, the number of 9783

router activations to be included on the certificate.

To learn more about activating SLV capability, refer to the

FrameSaver SLV Activation

Instructions

(Document No. 9000-A2-GK43), or contact your sales representative.

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com.

Select

Library

→

Technical Manuals

→

FrameSaver Frame Relay Devices.

Select the following document:

9783-A2-GB20

FrameSaver DSL 9783

User’s Guide

To order a paper copy of a Paradyne document:



Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)



Outside the U.S.A., call 1-727-530-8623

Package Checklist

In addition to these instructions, verify that your package contains the following:

❑FrameSaver DSL 9783 Router

❑Power cord with power transformer

❑Tie wrap for power cord strain relief

❑DSL network access cable with 8-pin connectors –U.S. models only

❑Ferrite choke –International models only

❑

FrameSaver DSL 9783 Router Quick Reference

(Document No. 9783-A2-GL11)

Be sure to register your warranty at www.paradyne.com/warranty.

Wiring and Cables You May Need

The following wiring and cables are used with this product, which uses standard

interface connectors:

❑Standard connectors: An 8-pin modular (similar to RJ48C) or 6-pin modular

(similar to RJ11) wall jack for the DSL network connection.

❑DSL wiring: Unshielded twisted-pair wiring (CAT3, or better). The CAT3 wiring must

meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or 26 AWG (.4 mm).

❑Ethernet wiring: Shielded twisted-pair wiring (CAT5, or better). The CAT5

wiring must meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or

26 AWG (.4 mm).

For standard cables, refer to

Cables and Connectors

on page 21 for pin numbers.

For Paradyne cables, contact your sales representative to order them.

Interface

Connection Cables Feature

Number

COM port to a PC

or asynchronous

terminal

DB25-to-DB25:

Standard EIA-232 straight-through cable —

DB25-to-DB9:



DB25-to-8-pin modular adapter



8-pin modular-to-DB9 cable

(14 feet –4.3 m)

3100-F1-920

3100-F2-550

ETHERNET port

to a NIC on a PC

or an Ethernet hub

For connection to a PC NIC:

Standard Ethernet crossover cable —

For connection to an Ethernet Hub:

Standard Ethernet straight-through cable —

NETwork to the

DSL wall jack Standard straight-through DSL network cable

with 8-pin modular connectors –similar to an

RJ48C-toRJ48C cable (20 feet –6.1 m).

Cable supplied for use in the U.S.

3100-F1-500

Standard DSL network cable with

6-pin connectors –similar to an RJ11 cable —

Prior to Installing the Router

These Installation Instructions assume that the virtual circuits at the DSLAM have

already been configured. Provisioning of these circuits can be simplified by using the

OpenLane SLM (Service Level Management) system, as indicated in

Provisioning Data

Circuits in OpenLane

Provisioning Data Circuits in OpenLane

Use the OpenLane SLM system’s Provision Circuit screen to add new circuits that start

at the FrameSaver DSL endpoint and traverse the SCM and ATM line card in the Hotwire

GranDSLAM, and the default VC sets (from 1 to 4). A group of 250 VCscan be allocated

to each line card, which can be assigned to any port on the card. These custom

connections carry the frame relay traffic.



Note that before the custom cross-connects are configured, the Maximum VCI

number for the uplink VP to be used by these custom connections must be

specified on the Max VCI per VPI screen, and the apply changes executed.



For ATM line cards, custom connections can be used to expand the number of VCs

connected to the card. Each of the 250 VCs can be cross-connected from any VC

on the uplink to any port on the line card.

The following information is collected by the Provision Circuit process:



Uplink VPI/VCI



Slot number and Port number of the DSL connection



Traffic Profile



DSL link VPI/VCI



Frame relay DLCI (provided by NSP)



Frame relay CIR, Be, Bc(provided by NSP)

A Circuit ID is then applied to the newly defined circuit, and stored in both the router and

the OpenLane SLM system.

Installing the Router

Place the FrameSaver DSL 9783 Router on a flat surface, with clearance for the rear

connectors.

Procedure

1. Use the supplied 8-pin DSL network cable (for use in the U.S.), or a 6-pin DSL

network cable (using connectors similar to RJ11), as applicable, for the DSL

connection. Insert one end of the cable into the jack labeled NET on the router.

Insert the other end into the wall jack for DSL data communications.

For domestic models, go to Step 3 on page 7.

2. For certain international models, a ferrite

choke has been provided. Place the ferrite

choke on the network cable, as close as

possible to the rear panel.

Close the two halves around the cable

and snap the latch shut.

DSL

Network

00-16878

ETHERNET

COM

POWER NET

NET

DSL 9783 Router

DSL

Network

01-16944

NET

Ferrite

Choke

3. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable

into the jack labeled ETHERNET.

—Use a straight-through cable to connect the other end of the cable to an

Ethernet hub. Do not connect to the hub’s optional Uplink connection with a

straight-through cable; the Uplink connection requires an Ethernet crossover

cable.

–or –

—Use an Ethernet crossover cable to connect to a PC with an Ethernet Network

Interface Card (NIC) installed or a hub’s Uplink connection.

00-16879

ETHERNET

COM

POWER NET

Ethernet

Straight-Through

Cable

ETHERNET

DSL 9783 Router

Hub

4. Use a VT100-compatible asynchronous terminal or PC to set up management

access to the unit. Insert the DB25 end of the EIA-232 cable into the router’s COM

port. Tighten the screws on each side of the connector. Insert the other end into the

terminal or PC.

The terminal or PC’s configuration must be compatible with the router’s. Refer to the

procedure on page 13 of

Configuration Setup

. If connecting an external modem to

the COM port, refer to

Connecting an External Modem

on page 23.

COM

Port

00-16876

ETHERNET

COM

POWER NET

VT100

Terminal

DSL 9783 Router

5. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the

transformer into an AC outlet.

Install the supplied tie wrap for strain relief, as shown.

Installation of the hardware is now complete. When the power cord is installed, the

router goes through a power-on self-test.

Power-On

When power is applied, the router performs self-diagnostics and the PWR LED is on.

The self-diagnostics include a power-on self-test where all of the LEDs are on.

Refer to

Status LEDs

on page 10 for information about the LEDs. Refer to

Troubleshooting

on page 11 for LED indications requiring action.

ALM

TEST

ATM

DSL

NetworkSystem Port

9783-C

SLV

FrameSaver®DSL

SDSL

01-16877-01

ETHERNET

COM

POWER NET

Grounded

Power

Outlet

Tie

Wrap

Power

Jack

ALM

TEST

ATM

DSL

NetworkSystem Port

9783

ROUTER

FrameSaver

SLV

FrameSaver®DSL

SDSL

01-16857-01

ALM

TEST

ATM

DSL

NetworkSystem Port

9783

ROUTER

SLV

FrameSaver®DSL

SDSL

System OK –green

Alarm –red

Test –yellow

ATM –green/yellow

DSL –green

Ethernet Port –green

Status LEDs

After a successful self-test, the LEDs should appear as indicated in BOLD in the

Condition column below.

LED Condition Status

System LEDs

OK ON The router has power.

ALM ON

OFF

An alarm condition exists.

No alarms have been detected by the router.

TEST ON

OFF

The router is performing the power-on self-test, or a test

initiated by the service provider is currently active.

No tests are active.

Network LEDs

ATM ON –Green

ON –Yellow

ATM mode is active and cell delineation is in sync.

ATM mode is active and there is loss of cell delineation.

DSL Blinking

OFF

The router is in start-up or is retraining. The LED blinks on

and off about five times per second.

The DSL link is ready to transmit and receive data.

No DSL link has been established, or the link is down.

Port LED

OK ON

OFF

The Ethernet port is transmitting and receiving data.

Self-diagnostics have not been completed successfully.

Other manuals for FrameSaver 9783

Table of contents

Other Paradyne Network Router manuals

Paradyne

Paradyne 6382 User manual

Paradyne

Paradyne FrameSaver 9720 User manual

Paradyne

Paradyne Hotwire 6212 User manual

Paradyne

Paradyne Hotwire 7995 Original operating instructions

Paradyne

Paradyne FrameSaver 9123 User manual

Paradyne

Paradyne Hotwire 6381 User manual

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU User manual

Paradyne

Paradyne 1754 SHDSL Original operating instructions

Paradyne

Paradyne Hotwire 6381 Quick start guide

Paradyne

Paradyne 6381-A3 User manual

Paradyne

Paradyne HotWire 5246 User manual

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU User manual

Paradyne

Paradyne 1740 SHDSL Original operating instructions

Paradyne

Paradyne Hotwire 6301 User manual

Paradyne

Paradyne Hotwire 6351 User manual

Paradyne

Paradyne FrameSaver DSL 9783 CSU/DSU User manual

Paradyne

Paradyne 1740 SHDSL User manual

Paradyne

Paradyne 6212-I1 User manual

Paradyne

Paradyne Hotwire 6341 User manual

Paradyne

Paradyne 1740 SHDSL User manual

Paradyne

Paradyne Hotwire 6321 User manual

Paradyne

Paradyne Hotwire 6381 User manual

Paradyne

Paradyne FrameSaver SLV 9664 User manual

Paradyne

Paradyne iMarc DSL 9783 User manual

Popular Network Router manuals by other brands

Allnet

Allnet ALL0333AU user guide

HomeSeer

HomeSeer HT-SEL Getting started guide

Sercomm

Sercomm Genesis OC3505D Quick installation guide

Billion

Billion BIPAC 5102 Series user manual

TP-Link

TP-Link TD-8817 QIG

Motorola

Motorola MR1900 user guide

Digi

Digi IX14 user guide

Cisco

Cisco NCS 540 Hardware installation guide

XAVi

XAVi X8821e user manual

BEC

BEC 6200WZL Quick installation guide

MikroTik

MikroTik hAP ac3 Series quick start

Korenix

Korenix JetNet 5428G Series user manual

NETGEAR

NETGEAR FS526T - Switch installation guide

Korenix

Korenix JetNet 5710G Series user manual

Automated Logic

Automated Logic ZN551 Technical instructions

Cisco

Cisco ASR 1000 Series Installation and configuration guide

EnGenius

EnGenius ESR-9710 quick start guide

Cisco

Cisco 805 Series Product overview