Paradyne Hotwire 6341 User manual
1
Hotwirer6341/6342 Symmetric DSL Routers
Installation Instructions
Document Number 6341-A2-GN10-00
February 2000
Contents
Hotwire 6341/6342 SDSL Routers Overview 2. . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring and Cables Needed 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the DSL Access Wiring 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to the DSL Access Wiring 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Hotwire 6341/6342 SDSL Router 7. . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cables & Connectors 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important Safety Instructions 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Documentation on the World Wide Web
We provide complete product documentation online. This lets you search the
documentation for specific topics and print only what you need, reducing the waste of
surplus printing. It also helps us maintain competitive prices for our products.
Complete documentation for this product is available at www.paradyne.com.
Select Library →Technical Manuals →Hotwire DSL and MVL Systems.
Select the following document:
6371-A2-GB20
Hotwire DSL Routers User’s Guide
To request a paper copy of a Paradyne document:
HWithin the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
HOutside the U.S.A., call 1-727-530-8623
Product-Related Documents
Document Number Document Title
8000-A2-GB26 Hotwire MVL, RADSL, and Packet SDSL Cards, Models
8310/8312, 8510/8373/8374, and 8343/8344, User’s Guide
8000-A2-GB27 Hotwire Network Design Guide: Bridged Model
2
Hotwire 6341/6342 SDSL Router Overview
The Hotwirer6341 and 6342 Symmetric DSL Routers are components in the Hotwire
DSLAM (Digital Subscriber Line Access Multiplexer) system. Both Hotwire SDSL
Routers interoperate with either the Hotwire 8343 or 8344 Packet SDSL Card:
HHotwire 6341 SDSL Router with one Ethernet port
HHotwire 6342 SDSL Router with a four-port Ethernet hub
Both the Hotwire 6341 and the Hotwire 6342 SDSL Routers operate as an IP router
connecting a DSL link to an Ethernet network. The Hotwire SDSL packet-based system
provides high-speed Internet or corporate LAN access over traditional twisted-pair
copper telephone wiring. These products are configurable from 144 kbps up to
2.3 Mbps.
Copper pairs run from the central office to the customer premises to create the local
loop. The local loop terminates on the customer premises at the demarcation point in a
punchdown block or network interface device (NID).
Network Overview with a Hotwire 6341 SDSL Router
99-16588
Punchdown
Block or NID
DSL
Jack 6341
SDSL
Router
Customer Premises (CP)
DSL Ethernet
Crossover
Cable Ethernet
Cable
or
Central
Office
(CO)
Demarcation
Point
Local Loop
Hub
End-user
Systems
DSL – Digital Subscriber Line New Wiring Connections
NID – Network Interface Device
Service
Provider
3
Network Overview with a Hotwire 6342 SDSL Router
99-16639
Punchdown
Block or NID
DSL
Jack 6342
SDSL
Router
Customer Premises (CP)
DSL
Ethernet
Crossover
Cable
Ethernet Straight
Through Cables
Central
Office
(CO)
Demarcation
Point
Local Loop
Hub
End-user
Systems
DSL –Digital Subscriber Line New Wiring Connections
NID –Network Interface Device
Service
Provider
NOTE:
For Ethernet cabling details, refer to Installing the Hotwire 6341/6342 SDSL Router
on page 7.
Package Checklist
Verify that your package contains the following:
-Model 6341 or Model 6342 SDSL Router
-DSL interface cable with RJ11 modular plugs
-Power cord with power transformer
Wiring and Cables Needed
You will need the following wiring and standard connectors with this product:
-Standard RJ11 wall jack for the DSL cabling.
-DSL cabling: New or existing unshielded twisted-pair wiring (CAT3 or better). The
CAT3 wiring must meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or
26 AWG (.4 mm).
-Ethernet cabling: New or existing shielded twisted-pair wiring (CAT5 or better). The
CAT5 wiring must meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or
26 AWG (.4 mm). A straight-through or crossover Ethernet cable is used.
Refer to Installing the Hotwire 6341/6342 SDSL Router on page 7 for cabling details.
4
Optional Cable
The Hotwire 6341/6342 SDSL Routers are typically configured remotely by the service
provider. The following optional cabling and adapter are only used with this product to
configure the router locally:
-Console cabling: Straight-through cable with 8-pin non-keyed modular plugs
(Part No. 035-0276-1431)
-Console adapter:
—8-pin modular to DB9 adapter plug (Part No. 002-0093-0031), or
—A configurable RJ to DB9 adapter wired as shown in Cables & Connectors
on page 14.
Installing the DSL Access Wiring
The local loop terminates at the punchdown block or NID. Wiring must be connected
from the customer premises side of the punchdown block or the NID to an RJ11 jack.
Typically, the punchdown block is installed in commercial locations and the NID is
installed in residential locations.
"Procedure
1. Access the punchdown block or NID.
!WARNING:
Do not continue unless the DSL access line from the local loop has been
disconnected at the NID or punchdown block. Refer to Important Safety
Instructions on page 19.
5
2. Disconnect the DSL access pair from the local loop.
A punchdown block is used in the following example.
ABCD
DSL
Access
from Local
Loop
Wiring to
DSL Jack
Bridge Clip
Punchdown Block
97-15348
Demarcation Point
Customer Premises
3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the
NID or punchdown block. Attach the wiring that will be connected to the DSL jack.
NOTES:
In this document:
—End-user system is used to represent any host with an Ethernet connection.
—Service provider is used to represent any Internet Service Provider (ISP) or
remote LAN provider.
6
Connecting to the DSL Access Wiring
The Hotwire 6341 or 6342 SDSL Router connects to the local loop via wiring from the
demarcation point to an RJ11 wall jack. The DSL twisted-pair wiring from the local loop
terminates at a new or existing wall jack. It may be necessary to install a standard
single RJ11 jack or replace a single jack with a double RJ11 jack.
99-16589
DSL
RJ11
Jack
Central
Office
Punchdown
Block or NID
Customer Premises
DSL
Local Loop
Demarcation Point DSL
Twisted-pair
Wiring
DSL
Router
"Procedure
1. Wiring can be run from the punchdown block or NID to a new or existing wall jack.
Match the pair colors on both ends.
2. Label the DSL jack.
3. Reconnect the DSL access pair at the punchdown block or NID. Tighten both
terminal screws with a flat-blade screwdriver.
The RJ11 6-pin jack uses the center two pins. For pin assignments, refer to Cables &
Connectors on page 14.
7
Installing the Hotwire 6341/6342 SDSL Router
Place the Hotwire 6341/6342 SDSL Router on a flat surface with clearance for the rear
connectors.
NOTE:
The following illustrations show the Hotwire 6342 SDSL Router with a 4-port
Ethernet hub. The Hotwire 6341 SDSL Router is identical except that it has one
Ethernet port.
"Procedure
1. Use the RJ11 6-pin cable for the DSL connection. Insert one end of the cable into
the jack labeled DSL. Insert the other end into the wall jack labeled DSL.
99-16581
DSL
Jack
POWER
CONSOLE DSL
2
1ETHERNET
34
6342 SDSL Router
If you are installing a . . . Then go to . . .
Hotwire 6341 SDSL Router page 8
Hotwire 6342 SDSL Router page 9
8
2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the
cable into the jack labeled ETHERNET.
If you are installing the Hotwire 6342 SDSL Router, go to page 9.
HFor a 6341 SDSL router, use a straight-through cable to connect the other end
to an Ethernet hub. Do not connect a straight-through cable to the external
hub’s UPLINK connection (this connection requires a crossover cable).
POWER
CONSOLE
DSL
ETHERNET
99-16506
Ethernet
Line
Ethernet
Hub
Ethernet
Straight-through
Cable
87654321
6341 SDSL Router
-or-
HFor a 6341 SDSL router, use an Ethernet crossover cable and connect the
other end to a PC with an Ethernet Network Interface Card (NIC) installed.
POWER
CONSOLE
DSL
ETHERNET
99-16637
PC with Ethernet
Network Interface
Card (NIC) Ethernet
Line
Ethernet
Crossover
Cable
6341 SDSL Router
9
If you are installing the Hotwire 6341 SDSL Router, go to page 8.
HFor a 6342 SDSL router, use a straight-through cable to connect the other end
to a PC with an Ethernet Network Interface Card (NIC) installed.
-and/or-
HUse an Ethernet crossover cable to connect the other end to an external hub.
99-16583
Ethernet
Crossover
Cable
Ethernet
Hub
87654321
Ethernet
Line
POWER
CONSOLE
DSL
2
1ETHERNET
34
6342 SDSL Router
For the SDSL router cable pin assignments, refer to Cables & Connectors on
page 14.
3. The Console port acts as a DCE and uses an 8-pin straight-through cable for the
connection to a VT100-compatible terminal or a PC running a terminal emulation
program.
This is an optional connection used only for local configuration of the DSL router.
For details, refer to Local Console Access on page 13.
Connect the DB9 adapter to the PC and connect the cable to a PC or laptop. lnsert
one end of the straight-through cable into the jack labeled CONSOLE. Insert the
other end into the DB9 adapter for the serial port of the VT100 terminal or PC.
POWER
CONSOLE DSL
2
1ETHERNET
34
6342 SDSL Router
VT100 Terminal
or PC
(9-pin Adapter)
99-16584
Console
Serial Line
10
4. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the
transformer into an ac outlet.
POWER
CONSOLE
DSL
2
1ETHERNET
34
99-16585
18 Vdc
800 MA
Transformer
Power
Jack 6342 SDSL Router
The Hotwire 6341/6342 SDSL Router hardware installation is now complete. When the
power cord is installed, the SDSL router goes through a power-on self-test.
Power-On
When power is applied, the Hotwire 6341/6342 SDSL Router performs self-diagnostics
and the PWR LED is on. The self-diagnostics includes a power-on self-test. During the
power-on self-test, all of the LEDs turn on for one second.
TST DSL ETHERNET
ALMPWR
TM
00-16503-01
Power –green
Alarm –red
Test –yellow
Digital Subscriber Line –green
Ethernet Link 1 to 4 –green
6342
1234
Refer to Troubleshooting on page 12 for LED indications requiring action.
Other manuals for Hotwire 6341
1
This manual suits for next models
1
Table of contents
Other Paradyne Network Router manuals
Paradyne
Paradyne FrameSaver SLV 9664 User manual
Paradyne
Paradyne 1740 SHDSL User manual
Paradyne
Paradyne Hotwire 6211 Original operating instructions
Paradyne
Paradyne Hotwire 6351 User manual
Paradyne
Paradyne FrameSaver 9720 User manual
Paradyne
Paradyne Hotwire 6381 User manual
Paradyne
Paradyne Hotwire 6301 User manual
Paradyne
Paradyne FrameSaver DSL 9783 CSU/DSU User manual
Paradyne
Paradyne 1740 SHDSL Original operating instructions
Paradyne
Paradyne Hotwire 6351 User manual
Paradyne
Paradyne FrameSaver DSL 9783 CSU/DSU User manual
Paradyne
Paradyne Hotwire 6212 User manual
Paradyne
Paradyne Hotwire 6212 Original operating instructions
Paradyne
Paradyne 1752 SHDSL Original operating instructions
Paradyne
Paradyne Hotwire 6371 User manual
Paradyne
Paradyne 6212-I1 User manual
Paradyne
Paradyne FrameSaver 9123 User manual
Paradyne
Paradyne 1740 SHDSL User manual
Paradyne
Paradyne Hotwire 6301 User manual
Paradyne
Paradyne 1740 SHDSL User manual
