Panasonic K-EW114L03E User manual

HD IR Waterproof Fixed Network Camera

Quick Start Guide

Model No. K-EW114L03E

K-EW114L06E

K-EW114L08E

Version 1.0.0

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated DC12V in the IEC60950-1. (Refer to general introduction)

Please note: Do not connect two power supplying sources to the device at the same time; it may

result in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for anyproblems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for anyproblems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Thunder-proof device is recommended to be adopted to better prevent thunder.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

Dome enclosure is the optical component, do not touch the enclosure when you are installing the

device or clean the enclosure when you are doing maintenance work. Please use professional optical

clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result

in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

Important Safety Instructions

iii

.Table of Contents

1 Structure............................................................................................................................................1

1.1 Multiple-function Combination Cable...........................................................................1

1.2 Framework and Dimension ............................................................................................2

2 Device Installation...........................................................................................................................3

3 Quick Configuration Tool...............................................................................................................5

3.1 Overview.............................................................................................................................5

3.2 Operation............................................................................................................................5

4 Web Operation.................................................................................................................................7

4.1 Network Connection.........................................................................................................7

4.2 Login and Main Interface................................................................................................7

1 Structure

1.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See

Figure 1-1.

Figure 1-1 Multiple-function combination cable

Please refer to the following sheet for detailed information.

Port Name

Function

Connection

Note

LAN

Network port

Ethernet

Connect to standard Ethernet cable.

DC12V

Power input

port

Power input port. Input DC12V.

1.2 Framework and Dimension

Please refer to the following two figures for dimension information. The unit is mm. See Figure

1-2 and Figure 1-3.

Figure 1-2 Dimension illustration 1

Figure 1-3 Dimension illustration 2

2 Device Installation

Important

• Make sure that the installation area is strong enough to hold the product, such as a

concrete ceiling.

• Install the camera in the foundation area of the architecture or where sufficient strength

is assured.

• If a wall or ceiling board such as plasterboard is too weak to support the total weight, the

area shall be sufficiently reinforced.

Please see Figure 2-1 and Figure 2-2.

Step 1

Stick installation sticker to designated surface where you will install the device (wall or ceiling).

Step 2

Affix the installation template label (accessory) to the ceiling or wall, and use a pen to mark the

positions of the screws and cable mounting hole in the ceiling or wall. Remove the installation

template label and attach the camera with 3 screws (locally procured).

Step 3

Plug external wiring of the device properly.

Figure 2-1 Device installation 1

Step 4

Use Philip’s head screw (in accessories bag) to loosen adjusting screw.

Step 5

Adjust the device in all possible directions, and set its monitoring direction.

Step 6

Use Philip’s head screw to tighten the screws

Figure 2-2 Device installation 2

3 Quick Configuration Tool

3.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you

can use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

3.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 3-1.

In the device list interface, you can view device IP address, port number, subnet mask, default

gateway, MAC address and etc.

Figure 3-1 Search interface 1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure

3-2.

Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 3-2 Search interface 2

If you want to modify the device IP address without logging in the device web interface, you can

go to the configuration tool main interface to set.

In the configuration tool search interface (Figure 3-1), please select a device IP address and then

double click it to open the login interface. Or you can select an IP address and then click the

In Figure 3-3, you can view device IP address, user name, password and port. Please modify the

corresponding information to login.

Please note the port information here shall be identical with the port value you set in TCP port in

Web Network interface. Otherwise, you cannot login the device.

If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 3-3 Login prompt

After you logged in, the configuration tool main interface is shown as below. See Figure 3-4.

Figure 3-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please

refer to the Quick Configuration Tool User’s Manual included in the resources CD.

Other manuals for K-EW114L03E

This manual suits for next models

Table of contents

Other Panasonic Security Camera manuals

Panasonic

Panasonic WV-SPW311AL User manual

Panasonic

Panasonic WV-SF342 User manual

Panasonic

Panasonic OneHome KX-HCM110A User manual

Panasonic

Panasonic WV-S4550L Operating manual

Panasonic

Panasonic AW-UE100KP User manual

Panasonic

Panasonic BL-C1A - Network Camera Operating instructions

Panasonic

Panasonic Super Dynamic II WV-CS854B User manual

Panasonic

Panasonic GPKS822CU - COLOR CAMERA User manual

Panasonic

Panasonic WVCF254 - COLOR CAMERA User manual

Panasonic

Panasonic Super Dynamic III WV-CW964 User manual

Panasonic

Panasonic WV-CW474A Series User manual

Panasonic

Panasonic K-EW114L03E User manual

Panasonic

Panasonic WV-SW158 User manual

Panasonic

Panasonic Super Dynamic III WV-CS950 User manual

Panasonic

Panasonic WV-SW396 User manual

Panasonic

Panasonic WV-U2142L Installation guide

Panasonic

Panasonic WVNS954 - NETWORK CAMERA User manual

Panasonic

Panasonic WV-X5550LT User manual

Panasonic

Panasonic WV-V6430L User manual

Panasonic

Panasonic AWE860 - COLOR CAMERA User manual

Panasonic

Panasonic BL-C10A - Network Camera - Pan User manual

Panasonic

Panasonic BL-C111A - Network Camera - Pan User manual

Panasonic

Panasonic AKHC900 - COLOR CAMERA User manual

Panasonic

Panasonic WV-SW559 User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications