Overland Storage SnapServer XSR 120 User manual

*10400577001*

SnapServer XSR 120™

Add-on/Spare PCIe Card Instructions

This document describes how to add or replace a PCIe card in a

SnapServer XSR 120 from Overland Storage.

WARNING: To reduce the risk of electric shock or damage to

equipment, always remove any power cords while working

with the unit.

WARNUNG: Um das Risiko eines elektrischen Schlags oder

Schäden am Gerät zu vermeiden, ziehen Sie stets den

Netzstecker, bevor Sie an der Einheit arbeiten.

AVERTISSEMENT: Pour réduire le risque de choc électrique

ou endommagement de l'équipement, retirez toujours les

cordons électriques en travaillant avec l'appareil.

CAUTION: While working with the unit, observe standard

Electrostatic Discharge (ESD) precautions to prevent damage

to micro-circuitry or static-sensitive devices.

NOTE: If you are only replacing an existing PCIe card, skip to the

next section, “Prepare the Unit.”

When adding a PCIe card to your server, you must first

support are not available until this is done:

1. Go to the Overland Storage website

(http://www.overlandstorage.com/).

2. Select

Service & Support > My Products

3. At the Site Login, enter your e-mail address and

password, and click

4. Click the

Manage Products

button.

5. From the Product Selector drop-down list, select the XSR

120 in which you are installing the PCIe card.

6. Click

Add a Component

7. Enter the PCIe card information.

8. Click

Save & Exit

IMPORTANT: Your warranty certificate will be emailed to you.

Follow the instructions included to complete the process.

Enter

5325301507-SnapServer XSR 120 s/n: 02

Add-on/Spare PCIe Card Instructions

Prepare the Unit

Power Off and Disconnect

If the unit is still running, power it down cleanly:

1. Use the Web Management Interface to shut down the

server (Maintenance > Reboot and Shutdown >

Shutdown).

2. When all the LEDs are off, disconnect the power cords.

3. Disconnect the remaining cables from the unit, noting

their locations.

Remove the Front Bezel

1. Carefully take hold of the front bezel and pull it straight

out from the appliance until the magnets release.

2. Set the bezel aside on a secure surface.

Remove the Drives

IMPORTANT: Overland recommends that you remove the disk

drives to reduce the unit’s weight prior to removal.

Remove all the drive carriers, noting from which slot they were

removed. Blank carriers can remain in their bays.

NOTE: Do not remove the disk drives from their carriers. Doing so

voids the drive warranty.

1. Press the release button on the right side of the carrier.

2. Using the built-in handle, pull the carrier out.

3. Number the carrier and set it on a secure surface.

4. Repeat Steps 1–3 for all the remaining drive carriers.

Remove Unit from Rack

WARNING: It is recommended that a mechanical lifter (or at

least two people) be used during rack installation or removal

to prevent injury.

WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir

zur Rack-Installation oder -Deinstallation die Nutzung einer

mechanischen Hebehilfe (oder mindestens zwei Personen).

AVERTISSEMENT: Pour éviter toute blessure il est

recommande qu'un monte-charge (ou deux personnes au

moins) soit utilisé lors de l'installation ou de l'enlèvement du

support.

1. Remove and retain the four screws securing the unit to

the rack.

2. With a lifter positioned in front of the array, release the

rail locks and slide the chassis out onto the lifter.

3. Move the chassis onto a secure surface.

PressPull Handle

Secure Surface

Add-on/Spare PCIe Card Instructions

Install PCIe Cards

Remove Top Panels

1. Remove and retain the two screws located at the front

edge of the panel.

2. Loosen the two captive screws securing the panel rear.

3. Slide the panel toward the rear about one-half inch

(1.25cm), lift it off, and set aside.

Add a New PCIe Card

NOTE: If you are only replacing an existing PCIe card, skip to the

next section, “Replace a PCIe Card.”

1. Remove and retain the rear slot cover and screw from

an appropriate PCIe card slot.

2. Insert the PCIe card in the slot and seat it properly.

3. Secure it with the retained slot cover screw.

Replace a PCIe Card

1. Remove and retain the slot cover screw of the PCIe card

being replaced.

2. Grasp the PCIe card and carefully pull it straight up and

out of the chassis slot.

Set the PCIe card aside on an ESD-safe surface.

3. Insert the new PCIe card in the same slot and secure it

with the retained slot cover screw.

Reassemble the Unit

Reinstall Top Panel

1. Position the top panel with no more than one-half inch

(1.25cm) extending out over the rear of the unit.

2. Slide the panel forward until it is fully seated.

3. Using the two captive screws, secure the panel rear.

4. Using the two retained screws, secure the panel front.

Return Chassis to Rack

1. Slide out the middle rails from the rack.

2. Using the mechanical lifter, position the chassis in front

of the rack.

3. Insert the inner rails into the middle rails and slide the

unit into the rack.

4. Using the four retained screws, secure the SnapServer

to the front of the rack.

Rear

Front Screws

Captive

Screws

Screw

Rear

Front Screws

Captive

Screws

http://support.overlandstorage.com

You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using

the information found on the Contact Us page on our web site.

Add-on/Spare PCIe Card Instructions

Reinstall Drives

Return the drive carriers to the same drive bays:

1. Referring to the numbering, position a drive assembly in

front of its empty bay in the new chassis.

2. Slide the assembly in until the latch clicks, securing it.

3. Repeat Steps 1–2 for all remaining drive carriers.

IMPORTANT: To maintain proper airflow and cooling, a drive

assembly or a blank carrier must be installed in every bay. No

empty bays are allowed.

Reattach Cables and Power Cords

1. Reattach all cables to the same connections as before.

2. Attach the power cords.

3. At the front of the unit, press the power switch for less

than a second to power the unit ON.

Reattach the Bezel

1. Position the bezel with the tabs aligned inside the top

and bottom edges of the chassis.

2. Move bezel toward the unit until the magnets connect.

3. Verify that the bezel is aligned properly, all the LEDs are

visible, and the Power panel is centered in the left flange.

Return Replaced Parts to Overland

1. Place the replaced part in the anti-static bag and put it

in the replacement part’s box.

2. Use an RMA to return the part to Overland Storage.

For return shipping details and RMA number, go to:

http://docs.overlandstorage.com/return-instructions

Push In Using Handle

Power Sockets Cable Ports

Magnets Tabs

Other manuals for SnapServer XSR 120

Table of contents

Other Overland Storage Storage manuals

Overland Storage

Overland Storage NEO Series User manual

Overland Storage

Overland Storage SnapServer DX1 User manual

Overland Storage

Overland Storage SnapServer DX2 User manual

Overland Storage

Overland Storage SnapSAN S3000 Service manual

Overland Storage

Overland Storage NEO 8000 Guide

Overland Storage

Overland Storage NEO 8000 User manual

Overland Storage

Overland Storage NEO 200S User manual

Overland Storage

Overland Storage NEO 200S User manual

Overland Storage

Overland Storage SnapServer XSD 40 User manual

Overland Storage

Overland Storage Ultamus Raid 1200 User manual

Overland Storage

Overland Storage SnapServer XSD 40 User manual

Overland Storage

Overland Storage SnapSAN S3000 User manual

Overland Storage

Overland Storage SnapServerXSR 40 User manual

Overland Storage

Overland Storage NEO 8000 User manual

Overland Storage

Overland Storage SnapServer Service manual

Overland Storage

Overland Storage Neo Series 2000 User manual

Overland Storage

Overland Storage SnapServer DX2 User manual

Overland Storage

Overland Storage SnapServer XSD 40 User manual

Overland Storage

Overland Storage REO 4600 User manual

Overland Storage

Overland Storage ARCvault 2U Series User manual

Overland Storage

Overland Storage NEO 2000e User manual

Overland Storage

Overland Storage ARCvault Series Guide

Overland Storage

Overland Storage NEO 8000 User manual

Overland Storage

Overland Storage NEO 2000e User manual

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

HP StorageWorks MSL2024 Getting started

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

HP P9000 user guide

Western Digital

Western Digital Ultrastar Data60 installation guide