Optika B-1000FL HBO User manual
B-1000FL HBO
OPERATION MANUAL
GUIDA UTENTE
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
BEDIENUNGSANLEITUNG
Page 3
INDEX
1.0 DESCRIPTION page 5
2.0 INTRODUCTION page 6
3.0 UNPACKING AND ASSEMBLY page 6
4.0 USING THE MICROSCOPE page 9
5.0 MAINTENANCE page 12
6.0 ELECTRICAL SPECIFICATION page 12
7.0 RECOVERY AND RECYCLING page 13
Page 4
This microscope is a scientic precision instrument designed to last for many years with a minimum of main-
tenance. It is built to high optical and mechanical standards and to withstand daily use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this manual.
Safety guidelines
This manual contains important information and warnings regarding safety about installation, use and
maintenance of the microscope. Please read this manual carefully before using the equipment. To
ensure safe use, the user must read and follow all instructions in this manual. OPTIKA products are
designed for safe use in normal operating conditions. The equipment and accessories described in
the manual are manufactured and tested according to industry standards for safety instrumentation
laboratory. Misuse can cause personal injury or damage to the instrument. Keep this manual at hand
close to the instrument, for an easy consultation.
Electrical safety
Before connecting the power cord to wall outlet, ensure that your mains voltage for your region corre-
sponds to the voltage supply of the instrument, and that the illuminator’s switch is in position OFF. The
user must observe the safety regulations in force in his region. The instrument is equipped with CE
safety marking, in any case the user has full responsibility concerning the safe use of that instrument.
Warning/Caution symbols used in this manual
The user should be aware of safety aspects when using the instrument. Warning or hazard symbols
are shown below. These symbols are used in this manual.
Follow the instructions on this symbol to avoid possible severe personal injuries.
Warning of use; the incorrect operation on the instrument can cause damages
to the person or instrument.
Possibility of electric shock.
Attention: high temperature surfaces. Avoid direct contact.
Technical notes or usage tips.
SAFETY GUIDELINES
Page 5
1.0 DESCRIPTION
APERTURE DIAPHGRAM
FILTER WHEEL
FLUORESCENCE LIGHT
SHUTTER ATTACHMENT FIXING
SCREW
HBO LAMP CASE
FIELD DIAPHGRAM
Page 6
2.0 INTRODUCTION
3.0 UNPACKING AND ASSEMBLY
3.1 The components are stored in 2 separated boxes: one containing epiuorescence attachment, and
one containing power supply and mercury lamp case. Remove the protection caps from the top of the
main B-1000 body and from the epiilluminator and place the epiilluminator on the top of the microsco-
pe body. Tighten the screw on the right side using the provided allen wrench.
3.2 Insert the mercury lamp case on the back of the epiilluminator and tighten the screws using the provi-
ded allen wrench.
This equipment is a scientic precision instrument designed to last for many years with a minimum of main-
tenance. It is built to high optical and mechanical standards and to withstand daily classroom and laboratory
use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument uses that do not comply with this manual.
Page 7
3.0 UNPACKING AND ASSEMBLY
3.3 Fix the orange protection screen to the front of the epiilluminator with the two provided screws.
3.4 Mercury lamp insertion: Loosen the lock-screw on the top of the lamp case. The lamp holder will
come out with the door.
Lock screw
Page 8
Remove the plastic placeholder.
Use protection glasses as, if handled carelessly, there is a risk that the lamp may shatter and eject
glass splinters. Thus, without touching the glass part of the lamp, take out the uorescence lamp from
its box, taking care not to exert stress on any part of the lamp. Put one end inside the exible metal
holder (note: it ts only in one direction) and then in the xed one. Tighten the screws just enough to
make it stay in place.If you tighten them too much the lamp may shatter.
Put the lamp door with lamp assembly back in place.
3.5 Connect the lamp case to the power supply trough the provided 3-poles cable.
3.0 UNPACKING AND ASSEMBLY
Page 9
4.1 Turn on the power supply using the power switch. Wait until the current display shows about
4.5 A. If the current falls below 4 A, replace the lamp. You should now wait for at least 10
minutes before aligning and using the lamp.
4.2 Aligning the mercury lamp
Move the lter selector of the lter wheel on the desired position, corresponding to an excitation
wavelength.
Insert a specimen slide and focus with 4X objective.
Fully open the eld and aperture diaphgrams.
Adjust the two lamp centering screws on the case, in order to maximize the light intensity emitted by
the sample.
Adjust the focus of the collector lens until the sample is uniformly illuminated (if the lamp is not cor-
rectly focussed, there will be a bright spot of light in the center of the eld, and dark outside).
Note: if the current display shows 0 A for many seconds after switching on, press the Trigger button
(2-3 times if needed) until a current begins to ow in the lamp.
4.0 USING THE MICROSCOPE
Page 10
The lamp case allows also a ne tuning of the orientation of the mirror located at the back of the
lamp, this could improve the intensity of illumination.
4.0 USING THE MICROSCOPE
Y LAMP MOVEMENT
LENS FOCUS
ADJUSTMENT
X LAMP MOVEMENT
MIRROR ALIGNMENT KNOBS
(ON THE BACK OF LAMP
CASE)
Table of contents
Languages:
Other Optika Microscope manuals
Optika
Optika OPTIStar OS-SZ1 User manual
Optika
Optika B-1000 Series User manual
Optika
Optika B-1000Ti-2 User manual
Optika
Optika STEREO Series User manual
Optika
Optika ECOVISION Series User manual
Optika
Optika B-150 ALC Series User manual
Optika
Optika OPTIGEM User manual
Optika
Optika OPTIKAM FAST3 Series User manual
Optika
Optika B-290 User manual
Optika
Optika XC-100L User manual
Optika
Optika B-500 MET User manual
Optika
Optika OPTISTAR OS-A1 Series User manual
Optika
Optika B-1000 POL User manual
Optika
Optika B-150 Series User manual
Optika
Optika B-190 User manual
Optika
Optika B-500TiFL User manual
Optika
Optika B-600 Installation manual
Optika
Optika B-600 MET User manual
Optika
Optika B-380 Series User manual
Optika
Optika B-500Ti-2 User manual
Popular Microscope manuals by other brands
VWR
VWR VisiScope 384 Series instruction manual
Nikon
Nikon ECLIPSE E200 POL instructions
Leica
Leica DI C800 User's manual & installation instructions
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
ThermoFisher Scientific
ThermoFisher Scientific Continuµm manual
Olympus
Olympus SZ61 instructions