Omron THERMAC NEO Series Instruction manual

OMRON Corporation

Temperature Controller

CompoWay/F Driver

1 System Configuration....................................................................................................... 3

2 Selection of External Device ............................................................................................ 7

3 Example of Communication Setting ................................................................................. 8

4 Setup Items ....................................................................................................................18

5 Cable Diagram ............................................................................................................... 23

6 Supported device ........................................................................................................... 38

7 Device Code and Address Code.................................................................................... 45

8 Error Messages.............................................................................................................. 47

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display and the External Device (target Temperature Controller).

In this manual, the connection procedure will be described by following the below sections:

1System Configuration

This section shows the types of the

External Device and SIO type.

)"1 System Configuration" (page 3)

2Selection of External Device

Select a model (series) of the External

Device to be connected and connection

method.

)"2 Selection of External Device" (page 7)

3Example of Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Example of Communication Setting" (page

4Setup Items

This section describes communication

setup items on the Display.

Set communication settings of the Display

with GP-Pro EX or in offline mode.

)"4 Setup Items" (page 18)

5Cable Diagram

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagram" (page 23)

Operation

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of OMRON Corporation and the Display are

connected is shown.

Connection Configuration

• 1:1 Connections

• 1:n Connection

Series CPU*1

*1 Model number of the controller "" varies depending on the function specification of each controller.

Link I/F SIO Type

Communi-

cation

Settings

Cable

Diagram

THERMAC

NEO

E5EN--FLK

E5AN--FLK

Terminal block

on the

controller

RS232C

Setting

Example 1

(page 8)

Cable

Diagram 1

(page 24)

E5EN--FLK

E5AN--FLK

E5CN--FLK

E5GN--FLK

RS485

(2wire)

Setting

Example 2

(page 10)

Cable

Diagram 2

(page 26)

THERMAC

E5AR--FLK

E5ER--FLK

Terminal block

on the

controller

RS485

(2wire)

Setting

Example 3

(page 12)

Cable

Diagram 2

(page 26)

In-Panel

NEO E5ZN--FLK

Terminal block

on the

controller

RS485

(2wire) 1:1

Setting

Example 4

(page 14) Cable

Diagram 2

(page 26)

RS485

(2wire) 1:n

Setting

Example 5

(page 16)

Display

External Drive

Display

External

Drive

External

Drive

External

Drive

Maximum number of connections: 16 units

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 4

IPC COM Port

When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please

refer to the IPC manual for details.

Usable port

Series

Usable Port

RS-232C RS-422/485(4 wire) RS-422/485(2 wire)

PS-2000B COM1*1 , COM2,

COM3*1, COM4

*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.

PS-3450A, PS-3451A,

PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2

PS-3650A (T41 model),

PS-3651A (T41 model) COM1*1 --

PS-3650A (T42 model),

PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2

PS-3700A (Pentium®4-M)

PS-3710A

COM1*1, COM2*1,

COM3*2 , COM4

*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.

COM3*2 COM3*2

PS-3711A COM1*1, COM2*2 COM2*2 COM2*2

PS4000*3

*3 When making communication between an External Device and COM port on the Expansion slot,

only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the

specification of COM port.

For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.

Please refer to the IPC manual for details of pin layout.

COM1, COM2 - -

PL3000 COM1*1*2, COM2*1,

COM3, COM4 COM1*1*2 COM1*1*2

PE-4000B Atom N270 COM1, COM2 - -

PE-4000B Atom N2600 COM1, COM2 COM3*4 , COM4*4,

COM5*4, COM6*4

*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.

COM3*4, COM4*4,

COM5*4, COM6*4

PS5000 (Slim Panel Type

Core i3 Model) *5 *6 COM1, COM2*4 COM2*4 COM2*4

PS5000 (Slim Panel Type

Atom Model)

*5 *6

COM1, COM2*7 COM2*7 COM2*7

PS5000 (Enclosed Panel

Type)*8 COM1 - -

PS5000 (Modular Type

PFXPU/PFXPP)*5 *6

PS5000 (Modular Type

PFXPL2B5-6)

COM1*7 COM1*7 COM1*7

PS5000 (Modular Type

PFXPL2B1-4) COM1, COM2*7 COM2*7 COM2*7

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 5

DIP Switch settings (PL3000 / PS3000 Series)

RS-232C

*5 When setting up communication between an External Device and the RS-232C/422/485 interface

module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using

PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+

and 8.CTS+, and connect 6.RTS- and 9.CTS-.

When using RS-422/485 communication with External Devices, you may need to reduce the

transmission speed and increase the TX Wait time.

*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch

setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-

face.com/trans/en/manual/1001.html)

*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.

The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the

setting.

*8 For the connection with the External Device, on the user-created cable read as if the connector on

the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in

the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.

DIP Switch Setting Description

1OFF

*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.

Reserved (always OFF)

2OFF

SIO type: RS-232C

3OFF

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

Settings FAQ ID

PFXZPBMPR42P2, RS422/485 change method FA263858

PFXZPBMPR42P2 termination resistor setting FA263974

PFXZPBMPR44P2, RS422/485 change method FA264087

PFXZPBMPR44P2 termination resistor setting FA264088

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 6

RS-422/485 (4 wire)

RS-422/485 (2 wire)

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available

8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available

9ON

RS (RTS) Auto control mode: Enabled

10 ON

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 7

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Number of Devices/

PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the display.

Manufacturer Select the manufacturer of the External Device to connect. Select "OMRON Corporation".

Series

Select the External Device model (series) and the connection method. Select "Temp. Controller

CompoWay/F".

In System configuration, make sure the External Device you are connecting is supported by

"Temp. Controller CompoWay/F".

)"1 System Configuration" (page 3)

Port Select the Display port to connect to the External Device.

Use System Area Cannot be set in this driver.

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 8

3 Example of Communication Setting

Examples of communication settings of the Display and the External Device, recommended by Digital

Electronics Corp., are shown.

3.1 Setting Example 1

Setting of GP-Pro EX

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 9

Device Setting

To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]

window, select the external device and click [Settings] .

To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add

Device] to add another External Device.

Settings of External Device

Use the level key, mode key, down key and up key in front of the Temperature Controller for communication

settings of the External Device.

Please refer to the manual of the Temperature Controller for more details.

Procedure

1. Press and hold the level key (3 minutes or more) to transfer from the operation level to the default level.

2. Press the level key again to transfer from the default level to the communication setting level.

3. Press the mode key to select the parameter.

4. Press the down/up keys to change the setting.

5. Press and hold the level key to transfer to the operation level.

Setting Value

• Set the HOST link unit No. for "Unit No.".

PSEL CWF

U-NO 1

BPS 9.6

LEN 7

SBIT 2

PRTY EVEN

SDWT 2

• Parameters to be set vary depending on the Temperature Controller. Please refer to the manual of

the Temperature Controller for more details.

• Set Wait to Send to 2ms or more. Adjust Wait to Send according to the communication status.

Temperature Controller CompoWay/F Driver

GP-Pro EX Device/PLC Connection Manual 10

3.2 Setting Example 2

Setting of GP-Pro EX

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

This manual suits for next models

Table of contents

Other Omron Controllers manuals

Omron

Omron E5ARER User manual

Omron

Omron CK3W-AX2323 Series User guide

Omron

Omron CPM2C-S100C User manual

Omron

Omron G9SP-N20S Installation manual

Omron

Omron NE1A-SCPU01 - 07-2009 User manual

Omron

Omron SYSMAC C200H CPU01-E User manual

Omron

Omron CJ Series Instruction Manual

Omron

Omron Trajexia TJ1-DRT Quick user guide

Omron

Omron E5AK User manual

Omron

Omron Q2A-A Series Installation instructions

Omron

Omron NJ-series Instruction Manual

Omron

Omron E5DC User manual

Omron

Omron Smart Process Control CJ-Series User manual

Omron

Omron NJ-series Use and care manual

Omron

Omron SYSMAC NJ Series Instruction Manual

Omron

Omron E5AK User manual

Omron

Omron SYSMAC 3G8F7-CLK12-E User manual

Omron

Omron 1S Series User manual

Omron

Omron CK5M Series Instruction Manual

Omron

Omron CJ - INSTRUCTIONS User manual

Omron

Omron V600-CD1D-V2 User manual

Omron

Omron CJ1G/H-CPU series User manual

Omron

Omron MC3 Series User manual

Omron

Omron lFL-TCC1PS User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual