Olympus U-CBS User manual

Notes

This instruction manual is for the coded function system.

To ensure the safety, obtain optimum performance and to familiarize yourself fully with the use

of this product, we recommend that you study this manual thoroughly before operating this

product, and always keep this manual at hand when operating this product.

Retain this instruction manual in an easily accessible place near the work desk for future

reference.

For details of products included in the configuration of this system, see page 4.

Instructions

Coded function system

Optical Microscope Accessory

In accordance with European Directive on Waste Electrical and Electronic Equipment, this

symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in

your country.

This product is applied with the requirements of standard IEC/EN61326-1 concerning

electromagnetic compatibility.

- Immunity Applied to industrial and basic environment requirements.

For Korea only

이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서

가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

IMPORTANT -Be sure to read this section for safe use of the equipment.-................. 1

1 Nomenclature of each part............................................................................................................ 3

2 System diagram....................................................................................................................................... 4

3 Layout of the cables............................................................................................................................. 6

1Combining with the microscope frame (BX53F2) and U-IFRES..........................................................7

2Combining with the microscope frame (BX43F) and U-IFRES.............................................................8

3Combining with the microscope frame (BX43F)...............................................................................................9

4 Information readout / External transmission ...............................................................10

5 Specifications...........................................................................................................................................12

Contents

Coded function system

IMPORTANT -Be sure to read this section for safe use of the equipment.-

This system enables to read out the information from the coded illuminator and the coded revolving nosepiece and to

transmit the information externally.

Safety precautions

The following symbols are placed on this product.

Study the meaning of the symbols and always use the product in the safest possible manner.

Symbol Meaning

Indicates a non-specific general hazard. Follow the description given after this symbol or

in the instruction manual.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.

Safety symbols

·Before connecting the cables, be sure to set the POWER switch of the control box for coded function

(U-CBS) to OFF (out position).

·For safety, always use the provided AC adapter only.

·Keep the cables away from the lamp housings (halogen bulb, etc.) that become hot and the surroundings.

Otherwise, the cables may melt and cause an electric shock hazard.

·Never apply an excess force to cables, such as to stretch cables. Otherwise, they may be damaged.

Coded function system

·This product is a precision instrument. Handle it with care and connect cables gently to avoid

subjecting it to sudden or severe impact. Also, this product is not waterproof.

·Do not use the product in areas where it may be subjected to direct sunlight, high temperature and/or

humidity, dust or vibrations.

(For conditions of operating environments, see “5 Specifications“ on page 12.)

·Never connect or disconnect the cable while the POWER switch of the control box is set to ON

(depressed position). Otherwise, malfunction may result.

·Never disassemble any part of the product. Otherwise, failure may result.

·Before disposing of this product, be sure to follow the regulations and rules of your local government.

Contact Olympus for any questions.

CAUTION

2Handling Precautions

1Cautions

If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

product may also be damaged. Always use the product according to this instruction manual.

The following symbols are used in this instruction manual.

CAUTION

: Indicates a potentially hazardous situation which, if not avoided, may result in

damage to the equipment or other property.

TIP

: Indicates the useful knowledge or information for use.

Coded function system

1Nomenclature of each part

Control box for coded function

U-CBS

Microscope frame hanger (top)

Connector for hand switch

For external EXPOSE button of

microscope digital camera

Connector for BX3-CBM

Connector for AC adapter

RS-232C connector

Connector for coded revolving nosepiece

Connector for coded illuminator

POWER switch

ON: Depressed position

OFF: Out position

Microscope frame hanger (bottom)

Coded function system

2 System diagram

Coded illuminator

Control box for coded functionNote 3)

U-CBS

Microscope

frame

·The connectors of U-CBS are equipped with dust covers. Remove the dust covers only from the

connectors you want to connect cables.

·Be sure to connect only the units specified by Olympus to the connecters of U-CBS.

If a non-specified unit is connected, the performance of the entire system cannot be guaranteed.

·Before connecting the cables, be sure to set the POWER switch of U-CBS to OFF (out position).

Insert the cables securely to connectors paying attention to their shapes. If the connector is provided

with clamping screws, be sure to tighten them.

·If you insert a non-specified connector into the connector of U-CBS, the connector may be damaged.

CAUTION

· PC

· Microscope digital cameraNote 4)

Cable for coded illuminator Note 2)

RS-232C cableNote 1)

AC adapter

Cable for interface for coded nosepieceNote 2)

Interface for coded nosepiece

U-IFRES

Hand switch

U-HSEXP

Control box

BX3-CBM

Coded revolving

nosepiece

Interface for coded nosepiece

U-IFRES

Cable for revolving

nosepiece

Hand switch

U-HSEXP

Control box

BX3-CBM

Control box

BX3-CBM

AC adapter

Interface cable

CBSIFCBL200

Coded function system

Note 1)

RS-232C cable specifications

D-sub 9-pin (F) D-sub 9-pin (F)

Note 2)

Align the mark aon the connector of the coded illuminator with

the mark aof U-CBS and attach the coded illuminator. When

attaching U-IFRES or the coded revolving nosepiece, align marks

bin the same manner.

Note 3)

Hang U-CBS con the hangers don the back side of the

microscope frame.

Note 4)

When connecting the microscope digital camera to U-CBS to use

U-CBS, the order to turn ON the power is: 1POWER switch of

U-CBS and 2Switch of the microscope digital camera. If the

switches are set to ON in the different order, the microscope digital

camera cannot recognize U-CBS.

Also, if the connector of the coded revolving nosepiece are not

connected to U-CBS, U-CBS does not recognize the coded

revolving nosepiece. So be careful.

Coded function system

3Layout of the cables

The cables of units can be laid out easily by attaching the cable holders on the back side of the microscope frame.

The cable holders are provided with following units.

· Control box for coded function (U-CBS): 6 pieces

· Coded revolving nosepiece: 2 pieces

On page 7 and after, the positions to attach cable holders and the cable layout are described for each microscope frame.

· The number of cable holders to be used differs depending on the units combined with the microscope frame.

· If the cable holder positions are significantly deviated, the cable may not reach the connector. Attach the cable

holders while making sure that the cable reaches the connector.

· Make sure that cable holders are not deflected and close the cable holders.

TIP

Coded function system

About 69 mm

* :In case of laid out the cable for hand switch on the left side as shown above picture

**:In case of laid out the cable for hand switch on the right side as shown above picture

For procedures to attach the hand switch to microscope frame, see page 11.

TIP

Hand switch**

Cable holder**

Velcro tape

RS-232C cable

Coded illuminator

(provided with hand switch)

About 78 mm

AC adapter

Cable holder*

Hand switch*

About 85 mm

Cable holder*

Align with the upper left

corner of the label.

Coded revolving nosepiece

U-IFRES

1Combining with the microscope frame (BX53F2) and U-IFRES

Align with the height of

the edge between the

back side and under

side on the microscope

frame.

back side and under

side on the microscope

frame.

Table of contents

Other Olympus Microscope manuals

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Leica

Leica FL560 user manual