Olympus SZ4045TR User manual

(1) As the microscope is a piece of precision equipment, always handle with care, avoiding abrupt

movement or impact during transportation or Operation of controls.

(2) Avoid exposure to direct sunlight, high temperature and humidity, dust and Vibration.

(3) Avoid leaving dir-t or fingerprints on the lens surfaces, as a dirty mirror or lenses may reduce

image clarity.

(4) When using photomicrographic equipment or a large-size Video Camera, mount the microscope

body at an angle of less than 3” from the perpendicular in Order to assure microscope stability.

(5) Use a compact Video Camera, dedicated for C-mount, with a picture area of 2/3” or smaller and

weighing 2.5 kg or less.

(6) Be sure to hold the Camera with one hand when unloading film from a large-format Camera in

Order to prevent it from falling over.

(7) Never turn the right and left zoom control knobs in opposite directions, as malfunction may

result.

(1) Clean all glass components by wiping gently with gauze. To remove fingerprints or oil smudges,

wipe with gauze slightly moistened with a mixture of ether (70%) and alcohol 130%).

Since solvents such as ether and alcohol are highly flammable, they must be handled carefully.

Be sure to keep these chemicals away from open flames or potential sources of electrical

Sparks - for example, electrical equipment that is being switched on or off. Also remember

to always use these chemicals only in a weil-ventilated room.

(2) DO not use organic solutions to wipe the surfaces of other components. Plastic Parts especially,

should be cleaned with a neutral detergent.

(3) Never attempt to disassemble the microscope as decreased Performance may result.

(4) When not in use, be sure to cover the microscope with the dust cover provided, and store in

an area free from moisture to prevent rust.

CONTENTS

0 10 !-

Zoom stereo

microscope SZ4045TR-F

SZ6045TRF

SZ1145TR-F

0 0

Eyepiece GSWHI OX

Phototube SZ-PT

Photo eyepiece NFK3.3XLD

0 l 1 0

0 C

0 0 0

C-mount Video adaptt

Stand SZ-ST

Stage plate SP-BW-2

0 0

Stage Clip

0 C

Dust cover

0 C

Note: 0 indicates the compatible components for each model.

Zoom ratio

Working distance (W.D.1

Zoom stereo

microscope body 0.67X - 4X I IX-6.3X I 1.8-IlX

6 l 6.3 l 6.1

110 mm I 100 mm / 73 mm

Zoom drive Horizontal axial drive control knobs

Observation tube inclination 45O

Right and left tubes interlocked

Adjustment range: 50-76mm (with GSWHIOX)

Interpupillary distance

adjustment

Diopter adjustment Provided on one

eyepiece tube only Provided on both eyepiece tubes

Diopter adjustment range: +5 m-‘(per metar)

Screw-in fM48X0.75)Conversion lens mount

Photo tube/C-mount Video

adapter mount Fit into mounting port with inner diameter of 38 mm

With positioning pins

Light path selection Controlled by lever, 100% BI or 100% CAMERA

Eyepiece Field number (F.N.1 22 (GSWHIOX)

Eyepiece micrometer mount $24 mm micrometer mountable

Stand Fit into mounting port with inner diameter of 76 mmMicroscope body mount

Stage plate +lOOmm, frosted white on one side and black on the other side

Stage Clip Pressed down from above

Focusing Rack-and-pinion drive on ball bearing guides, knob rotation

tension adjustment, focusing range: 120 mm

Epi-illuminator (LSGA) and trans-illuminator base mountable

Illuminator mount

Mounting to microscope

body

Photo tube Fit into mounting port with outer diameter of 38 mm

With positioning groove

Photomicrographic equipment

mount Fit into mounting port with outer diameter of 38 mm

360’ rotatable

Intermediate magnification

Mounting to microscope body

C-mount Video

adapter Fit into mounting port with outer diameter of 38 mm

With positioning groove

Video Camera mount Video Camera mounting with C-mount

C-mount detachable and rotatable 360”

0.5x

Intermediate magnification

Tube length adjustment With tube length adjustment ring

With Photo tube 1

Photographit

eauioment mountina

oort

,---’ Tiqhten securely with a coin, etc.

wearing eyeglasses

Zoom control knob

(With C-mount Video adapter 1

1Video adapter 1

\ Clamping knob

Screw into the Video Camera and then

mount to the Video adapter.

Tube length

C mount

adjustment ring

- - Clamping knob

Tlghten securely with a coin, etc.

The diagram below illustrates the assembly procedure. The numbers indicate the assembly sequence.

+ Make sure all connecting surfaces are clean before assembly and avoid scratching the glass sutfaces.

IOM mount Camera1

I I

(1 I

I Photo micro adapter L

Eye shield

Eyepiece

1C-mount Video Camera 1

\8 y;

C-mount

“‘--7ninn

Video adapter

Eyepiece w, 0 ~

I 10 knob

...

.-------- 3odv

Body clamping knob

Stage Clip

IX ’

“1) Mount the C-mount to the Video Camera and then to the Video adapter.

“2) Mount photomicrographic equipment in accordance with its instruction manual.

Fig. 1

Fig. 2

Diopter adjustment ring

Fig. 3

Left diopter Right diopter

adjustment ring adjustment ring

Fig. 4

(1) Usually, the Stage plates are used with the frosted white side facing

the objective. However, if the specimen is white or brightly colored, use

the black side of the plate as the darkened background increases image

contrast.

(2) To remove the Stage plates, press down the supporting end of the plate

with a fingertip, and the other end will flip up. (Fig. 1)

(1) Turn one focusing knob with the other focusing knob tightened, by

holding both knobs, in Order to increase or decrease the rotation tension,

depending on the turning direction. (Fig. 2)

(2) This adjustment is intended to prevent the microscope body from drifting.

Set the knob tension at a level slightly stiffer than that to insure no

unintentional movement and facilitate easy Operation.

(1) Place the specimen in the Center of the Stage plate, and hold the specimen

with the Stage Clips if necessary.

(2) Illuminate the specimen using an optional illuminator.

For SZ4045TR

(1) Minimize the magnification power by turning the zoom control knobs.

(2) Looking through the right eyepiece, bring the specimen into focus by

turning the focusing knobs.

(3) Looking through the left eyepiece, bring the specimen into focus by

turning the diopter adjustment ring. (Fig. 3)

(4) Maximize the magnification power by turning the zoom control knobs,

and bring the specimen into focus by turning the focusing knobs.

For SZ6045TR and SZ1145TR

(1) Maximize the magnification power by turning the zoom control knobs.

(2) Looking through the right eyepiece, bring the specimen into focus by

turning the focusing knobs.

(3) Minimize the magnification power by turning the zoom control knobs.

(Fig. 3)

(4) If the specimen goes out of focus, read just the focus by turning the right

diopter adjustment ring only. (Fig. 4)

(5) Maximize the magnification power again by turning the zoom control

knobs. If the specimen goes out of focus, repeat Steps (2) through (4)

above. This allows more precise diopter adjustment.

(6) Minimize the magnification power by turning the zoom control knobs

and, looking through the left eyepiece, bring the specimen into focus by

turning the left diopter adjustment ring only. (Fig. 4)

Fig. 5

Fig. 6

Mounting ring ring

Fig. 7

Microscope

body

Extension tube

==%4 R==% Stand

Fig. 8

Holding the right and left eyepiece tubes, push or pull the tubes in the

direction of the ARROWS until perfett binocular Vision is obtained.

(Fig. 5)

(1) For those who do not wear eyeglasses

The observer tan keep his eyes closer to the eyepiece shields during hold

the diopter adjustment rings so that they tan not rotate, and align the

direction of the eyepiece shields to the observer’s face by turning the

eyepieces.

(2) For those who wear eyeglasses

Fold back the eyepiece shields with both hands as shown in Fig. 6.

(1) Twist and remove the mounting rings from the eyepiece. (Fig. 7)

(2) Remove dirt or dust from the eyepiece micrometer, and mount it to the

mounting ring by turning the ring clockwise with the inscription side

facing downward. (Fig. 7)

(3) Gently screw the mounting ring containing the eyepiece micrometer into

the eyepiece and tighten securely. (Fig. 7)

(4) To remove the eyepiece micrometer, twist the mounting ring. Wrap the

micrometer in clean, soft Paper for storage.

+ The e24-mm eyepiece micrometer tan also be mounted on the

GSWH15X, However, since the eyepiece’s field number is 16, the

micrometer graduations and grids beyond 16 mm are not visible.

(1) Screw the conversion lens into the mounting thread at the bottom of the

microscope body.

(2) As the working distance of the 0.5X conversion lens (llOAL0.5X and

lCOAL0.5X) is long, use the extension tube (VM-ET) when making

observations using the stand. (Fig. 8)

+ Please note that three types of conversion lenses are available-

one for the SZ4045 one for the SZ6045TR and the other for the

SZ1 145TR.

Ir 73AL0.5X doesn’t require extension tube.

This manual suits for next models

Other Olympus Microscope manuals

Olympus

Olympus MIC-D User manual

Olympus

Olympus IX70 User manual

Olympus

Olympus BX63 User manual

Olympus

Olympus CHD User manual

Olympus

Olympus CH2 Series Operating instructions

Olympus

Olympus BH2 Series User manual

Olympus

Olympus BX51WI User manual

Olympus

Olympus CX41 User manual

Olympus

Olympus SZX16 User manual

Olympus

Olympus CX41 Installation guide

Olympus

Olympus BX51 User manual

Olympus

Olympus BX61WI User manual

Olympus

Olympus CX21 User manual

Olympus

Olympus DP73 User manual

Olympus

Olympus AH3 Operating instructions

Olympus

Olympus Fluoview FV1000 Instruction Manual

Olympus

Olympus BX41 User manual

Olympus

Olympus BX60 User manual

Olympus

Olympus SZX16 Installation guide

Olympus

Olympus SZX-AR1 User manual

Olympus

Olympus BH2 Series Installation instructions

Olympus

Olympus FLUOVIEW FV300 User manual

Olympus

Olympus MIC-D Operating instructions

Olympus

Olympus DP21-SAL User guide

Popular Microscope manuals by other brands

Thermo Scientific

Thermo Scientific Nicolet iN10 Using

National

National DC3-163 instructions

KERN Optics

KERN Optics OPE-1 User instructions

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Operation manual

Prior

Prior Lux POL operating instructions

Opitec

Opitec Smartscoop 115615 instructions

KERN

KERN OPO-1 operating instructions

Topcon

Topcon SP-1P user manual

Motic

Motic PA43 Operation manual

Leica

Leica DVM5000 Setup manual

MshOt

MshOt MZ62 user manual

KERN Optics

KERN Optics OZR-5 User instructions

VWR

VWR VisiScope 384 Series instruction manual

Nikon

Nikon ECLIPSE E200 POL instructions

Leica

Leica DI C800 User's manual & installation instructions

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm manual

Leica

Leica FL560 user manual