Oki C712 User guide
Version 1.0
1
Thank you for choosing OKI.
This is C712 configuration instructions for Ballot model. These instructions explain 2 ways for
configuration. Manually and using Ballot Configuration Tool.
Before ballot configuration, please perform the following steps.
1. Install Extended 2nd Paper Tray for 19" Ballots (Order/Part Number 44274505).
2. Turn ON the device.
3. Print the Configuration pages. (Print Information -> Configuration -> Execute)
4. Check Serial Number and the current tray 2 setting from the configuration pages.
[Serial Number]
[Tray 2 Setting (Paper Size)] (Before Ballot Configuration)
Notes: Be sure to note down the serial number as it is necessary for inquiry.
If you do not have Ballot Configuration Tool you can set by using device menu, please
proceed to next page. In case you have Ballot Configuration Tool, please proceed to page 3.
Version 1.0
2
1. Installation Steps: Using Device panel menu (Manually)
Menus -> Tray Configuration -> Tray 2 Config
-> ->
1. Set Paper Size from “Cassette Size”
to “Custom”.
2. Return to “Tray 2 Config” Menu.
3. Set X Dimension to “8.5 inch”.
4. Set Y Dimension to “19.0 inch”.
5. Complete
Version 1.0
3
2. Installation Steps: Using Ballot Configuration Tool
①Connect the PC and the device with a USB cable.
②Copy the module of the Data Transmitter which provided by OKI to your desktop.
1. Run the Data Transmitter Tool “DT.exe”.
2. Select your language and click “OK”.
3. Select “Open” from the file menu.
4. Select “setup.dtd” file.
(To be Continued)
Version 1.0
4
5. Select “C712-b Configuration” function.
6. Search a USB connected printer. If the
device was found, select it, and click
“Send”.
7. Click “OK”.
Please wait for about 10 seconds.
After the applying configuration, the
device will restart (Turn OFF and ON)
automatically.
8. The configuration is completed. The
device will auto reboot (Turn OFF and
ON).
(To be Continued)
Version 1.0
5
9. After reboot, the device does initialize.
After initializing, the device status
changes to ready.
10. Click “OK” and close this tool.
11. Print the Configuration pages.
MENU -> Print Information ->
Configuration -> Execute
12. Check the current tray 2 setting from
the configuration pages.
Paper Size is “Custom”.
X Dimension is “8.5 inch”.
Y Dimension is “19.0 inch”.
13. Complete
Version 1.0
6
3. Confirmation of setup
You can check the setup result from the 1st page of Configuration pages.
How to print the Configuration pages. (Print Information -> Configuration -> Execute)
Where and what should you look up?
Setup was successful if the following were applied to the Tray 2 settings:
•Paper Size is “Custom”.
•X Dimension is “8.5 inch”.
•Y Dimension is “19.0 inch”.
If the above settings are not applied, please repeat above procedure.
End of File
This manual suits for next models
2
Table of contents
Other Oki Printer manuals
Oki
Oki PAGE 8p Plus User manual
Oki
Oki OKIPAGE 6w User manual
Oki
Oki C710dn User manual
Oki
Oki C6100dn Service manual
Oki
Oki C8800 series User manual
Oki
Oki proColor pro900DP User manual
Oki
Oki C6050dn Training manual
Oki
Oki ML3390 User manual
Oki
Oki PT341 Installation and operating instructions
Oki
Oki 6300FB User manual
Oki
Oki OKIPAGE20DX Training manual
Oki
Oki B431L6 User manual
Oki
Oki OKIPAGE18 User manual
Oki
Oki C7200 User manual
Oki
Oki C 9650dn User manual
Oki
Oki C711WT Manual
Oki
Oki C941dn Operating and maintenance instructions
Oki
Oki OKIPAGE8c Instruction Manual
Oki
Oki Microline 390 User manual
Oki
Oki D508 User manual
