NEC NEC Express5800 Series User manual

USERS_GUIDE_1080XD_hw

1-1

USERS_GUIDE_1080XD_hw

1-2

1.1 FEATURES OF EXPRESS SERVER

The Express server has as the following features.

High performance

•64-bit Intel® Itanium® 2 processor

- 1.3-/1.4-/1.5-GHz clock

- 6.4-GB/s system bus

- 3-/4-/6-MB on-chip L3 cache

- Large capacity memory addressing

- Simultaneous six instructions

- Floating operations with standalone peak performance of 3.6/4.0 GFLOPS

•Developing a high-performance chip set and crossbar interconnect that is fully utilising

supercomputer and mainframe technology.

High reliability

•Memory monitoring function (1-bit error correction/2-bit error detection available)

•Memory mirroring function

•Bus parity error detection

•Temperature detection

•Anomaly alarming

•Power supply unit and fan redundant function (Host swap supported)

High scalability

•Expandable up to 8 CPUs

•Large-size memory up to 64 GB

•Abundant number of IO optional slots

- 64bit 66MHz PCI bus (16 slots max. including a full-size PCIF unit)

- 64bit 133MHz PCI bus (10 slots max. including a full-size PCIF unit)

•PCI hot plug supported (varies depending on the slot)

Flexible operations

•Segmentation by the unit of 4 CPUs is available.

•Each subsystem (partition) is completely independent, offering individual OS operations.

Self-check function

•Power On Self-Test (POST)

USERS_GUIDE_1080XD_hw

1-3

1.2 NAME AND FUNCTION OF BLOCKS

Name of each block of the server is as follows.

1.2.1 Main Cabinet

Front view

(without front bezel)

Rear view

(cabinet back door opened)

8Way cabinet

View from the right side

(transparent)

②

②-1

②-2

②-4

②-6

②-7

②-9

②-1

②-3

②-8

②-9

④

③-3

③-1

③-4

④

③

正面背面

①-1①

②-5

③-2

USERS_GUIDE_1080XD_hw

1-4

(1) Switch pannel

(1)-1 AC switch

Main chasis AC power switch

(2) Main chasis

(2)-1 CELLV board

The CELLV board consists of a maximum of four Itanium2, one CPU Node

Controller (CNC), and a maximum of two Main Memory Controller

(MMC).Up to one CELLV board and two CELLV boards can be installed in

the 4Way main cabinet and 8Way main cabinet, respectively.

(2)-2 iSP-C card

iSP-C (service processor) card has an I/O interface (except for 1.6G interface)

in the basic processing device of the Express server as a standard. This iSP-C

card is installed in the main chasis of the main cabinet.

The following standard I/O interfaces are provided by an iSP-C card. The

interfaces from 1 to 3 are dedicated interfaces used to implement the system

control function and the RAS function.

1. 10/100BASE-TX Ethernet interface x1 for SP console

2. ICMB port x1 for IO cabinet control

3. Serial (RS-232C) interface x1 for SP console

(2)-3 Core module

Up to 12 PCI cards can be installed in the core module. Additionally, a BaseIO

card, which is used to support standard optional I/O interface, can be installed

in the core module.

(2)-4 DVD-ROM Drive

DVD-ROM and CD-ROM media can be used as DVD-ROM Device.

(2)-5 Floppy Disk Drive

Floppy Disk Medium can be used as Floppy Disk Drive.

(2)-6 Magnetic Disk Drive

Up to four 36.3 GB-73.2 GB Magnetic Disk Drives can be installed.

(2)-7 Power module

USERS_GUIDE_1080XD_hw

1-5

(2)-8 FANBOX (Core module)

FANBOX can be maintained online without aborting the system or turning off

the power.

(2)-9 FANBOX (Main chasis)

FANBOX can be maintained online without aborting the system or turning off

the power.

(3) Full-size PCIF unit

A full-size PCIF unit can be installed in an 8Way chassis as an option. Up to 14 PCI

cards can be installed in a full-size PCIF unit. Also, one BaseIO card and one VGA

card can be installed in a full-size PCIF unit to support a standard option I/O interface.

Installed PCI cards can be inserted/ejected (hot-swapped) online except for some types

of PCI cards (BaselO card/VGA card). That means it is not necessary to shut down or

reboot the basic processing device at the time of adding/exchanging PCI cards, which

leverages a high availability (a corresponding OS is required). A DVD-ROM device is

installed as default in the full-size PCIF unit. Up to six magnetic disks can be installed

as optional auxiliary memory devices.

(3)-1 DVD-ROM Drive (Optional)

DVD-ROM and CD-ROM media can be used as DVD-ROM Device.

(3)-2 Floppy Disk Drive

Floppy Disk Medium can be used as Floppy Disk Drive (which can be

connected to a full-size PCIX unit installed with a BaseIO card).

(3)-3 Magnetic Disk Drive (Optional)

Up to six 36.3GB-73.2GB Magnetic Disk Drives can be installed.

(3)-4 Slot for expanded PCI card (14 slots)

(4) Power Bay Unit

This unit supply DC power to the optional Full-size PCIX unit.

USERS_GUIDE_1080XD_hw

1-6

1.2.2 LED Display

This shows LED description of each card.

1.2.2.1 Main chasis

LED name LED status Function

ON AC ONAC ON/OFF Green OFF AC OFF

ON DC ON (ON at 48 V）DC ON/OFF Green OFF DC OFF

Green ON OS Ready for more than one node

ON Used for cabinet position checking during the maintenance mode

(through SP command cm) or maintenance

Status LED

Amber

OFF Upon troubles or at off-line

Status LED

DC ON/OFF

AC ON/OFF

USERS_GUIDE_1080XD_hw

1-7

1.2.2.2 Full-size PCIX unit (without frot bezel)

LED Name LED Status Description

Green ON DC ON Status

Amber ON DC Alarm

DC/ALM

Off DC OFF (full-size PCIX unit exchangeable)

ON Abnormal temperature (detected by the temperature sensor of

the IOR /PCIFB）

TEMP ALM Amber

OFF Normal Status

ON FAN Rotating Status

FAN ALM Amber OFF Normal Status

Full-size PCIX unit trouble (Logic alarm + DC alarm +

TEMP alarm + FAN alarm) or ON indication from SPFW

Turned on by the “led” execution of the “hc” subcommand of

the SP command

ATT Amber

OFF Normal Status

Green ON DC ON Status

Amber ON DC Alarm

DC/ALM

(Device Bay) OFF DC OFF

ON Abnormal temperatureTEMP ALM

(Device Bay) Amber OFF Normal Status

DC/ALM ATT

FAN_ALM(FAN#0,FAN#1,FAN#2,FAN#3)

TEMP_ALM DC/ALM(Device Bay)

TEMP_ALM(Device Bay)

USERS_GUIDE_1080XD_hw

1-8

1.3. INSTALLATION AND CONNECTION

1.3.1 Installation of Rack

A maintenance engineer installs a rack.

1.3.2 Installation/Removal of Cabinet

A maintenance engineer installs/removes a cabinet to/from a rack.

1.3.3 Connection

A maintenance engineer connects the Express sever and the peripheral devices.

USERS_GUIDE_1080XD_hw

1-9

1.4. BASIC OPERATION

1.4.1 System Boot/Shutdown

1.4.1.1 Steps for system boot

After installtion is completed (including the peripheral devies), you can boot the system

according to the following steps.

Caution Before booting the system, please confirm all I/O devices and tools are

upgraded and installed.

Flow of boot-up

スタート

電源ON

(1.4.1.1.1 電源のON 参照）

SPコンソール操作

(1.4.1.1.2 SP コンソール操作参照)

システムBIOS

いますか？

EFI Bootメニュー

(1.4.10 EFI Boot マネージャ参照 )

OS起動

POST

1.6.POST参照

BIOS Setup

(1.4.9 ｼｽﾃﾑｺﾝﾌｨｸﾞﾚｰｼｮﾝ参照)

Start

Power ON

(Refer to 1.4.1.1.1 Power ON)

SP console operations

(1.4.1.1.2 SP Console Operations)

Do you set up System BIOS?

EFI Boot menu

(1.4.10 EFI Boot manager)

OS boot-up

YesNo

POST

(1.6 POST)

BIOS setup (Refer to

1.4.9 System Configuration)

USERS_GUIDE_1080XD_hw

1-10

1.4.1.1.1 Power ON

This server has a different power-up procedure for AC and DC. When activating from the

AC power, follow the steps below.

1. Turn on the distribution board.

2. Turn on the power of the control PC (applicable only in Japan).

3. Turn on the AC breaker in the power receptacle box in the main chasis.

4. Turn on the power of the uncontrollable external peripheral devices from the main

cabinet and confirm they have been booted without errors.

5. When a full-size PCIX unit is attached, turn on the AC power breaker of PowerBay on

the bottom of the back of the main cabinet.

6. Turn on the AC switch in the switch box located at the top in the front panel of the

cabinet.

At this moment, the DC power remains off. The DC power should be turned on the SP

console.

Other manuals for NEC Express5800 Series

107

Table of contents

Other NEC Server manuals

NEC

NEC Express 5800/120Eh N8100 SERIES User manual

NEC

NEC NVM-Professional User manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC HV8600 User manual

NEC

NEC Express5800/R310g-E4 User manual

NEC

NEC Care Standard/300 Guide

NEC

NEC Express 5800/R120f-1M User manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC Express5800/120Rh-1 User manual

NEC

NEC Express5800 120Ed Reference guide

NEC

NEC Express5800/B120f User manual

NEC

NEC NECCare Platinum SigmaBlade User manual

NEC

NEC NEAX 2000 Owner's manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC Express5800/R120b-2 User manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC Express5800/R120h-1M User manual

NEC

NEC N8100-1078F User manual

NEC

NEC EXP804 User manual

NEC

NEC Express5800/180Ra-7 User manual

NEC

NEC NEC Express5800 Series User manual

NEC

NEC NEAX2000 IVS2 Operating and maintenance instructions

NEC

NEC Express5800/320Ma User manual

Popular Server manuals by other brands

HP AlphaServer ES47 Cli reference manual

Dell

Dell PowerEdge R410 Getting started

PowerNAS

PowerNAS CMA quick start guide

Supero

Supero FatTwin F617R3-FT user manual

MSI

MSI P1-109N-L70 user manual

Dell

Dell PowerEdge XE9640 Installation and service manual

Dell

Dell PS4100 Hardware

EtroVISION

EtroVISION EV3151 user manual

HP ProLiant Gen9 user guide

Compaq

Compaq ProLiant 3000 Maintenance and service guide

Dell

Dell PowerEdge 3YPMN Getting started guide

iRobo

iRobo IPC2U user manual

Nortel

Nortel 1000 Con?guration guide user manual

Asus

Asus AP7500 Hardware reference guide

Avid Technology

Avid Technology AirSpeed 5000 manual

HP Integrity rx2600 overview

Milestone

Milestone Husky IVO 350T Getting started

Planet

Planet NAS-7410 user manual