NEC NEC Express5800 Series User manual
SAP HANA Appliance
Express5800 A2040d
Initial Operation Verification Guide
23
rd
of January 2017
NEC SAP Global Competence Center
2 © NEC Corporation 2017
. Preparation
. . Check the Power Plugs
Plea e check that all power plug are connected to the back of erver.
.2. Check the NICs
.2. . Production Network
Plea e check that all Network Interface Card are connected a required. Thi mean the two
dual port adapter mounted in lot number 9 and 16 hould be connected. The e 4 1GB port
are bonded by the OS driver. For your reference plea e ee the number on top of the PCI lot.
The below image doe not contain NIC in the e lot .
.2.2. Management Network
Plea e check that at lea t one of both management adapter (MGB1 Management and MGB2
Management) i connected to the network. With thi connection you can monitor your hardware
health.
.3. External Storage (JBOD)
Plea e connect the external torage to the 2
nd
RAID controller.
The RAID controller i mounted in PCI lot 12. Plea e connect it port “A” to port “0” of the JBOD.
Plea e connect two power cable to the external torage a well.
3 © NEC Corporation 2017
2. Start the Server
2. . Power on the server
Pre ing the SYSTEM POWER Switch at the front of the erver turn on the erver.
Turn on the erver by u ing the following procedure.
Important
• Do not power on the server before amber SYSTEM POWER LED is unlit.
• Wait for at least 30 seconds before pressing the SYSTEM POWER switch on the server
after turning off the server.
1. Turn on the peripheral device and di play unit.
Note
If the power cord is connected to power control system such as an Uninterruptible Power Supply
(UPS), make sure that the power control system is turned on.
2. Remove Front Bezel, if mounted.
3. Pre the SYSTEM POWER witch at the front of the erver.
SYSTEM POWER LED i lit green and after a while, POST appear on the di play.
Important
Do not connect or disconnect USB device while POST is running. In addition, do not
connect or disconnect remote media.
Wait for the erver to fini h the boot operation. Once it ha completed you will be pre ented the
following login creen.
Plea e login to the OS.
4 © NEC Corporation 2017
2.2. Logon to the server
Depending on your in talled OS you will either be pre ented a graphical interface to login or a
CLI login prompt. In any ca e initial login credential are:
U ername : root
Pa word : hana
2.3. Start the SAP HANA Instance
1. Change u er to the < id>adm and tart HANA:
su - <sid>adm
HDB start
2. Check the SAP HANA In tance tatu , all hould be “GREEN”.
Plea e note that HANA tartup take ome time.
sapcontrol –nr <instance no> -function GetProcessList
3. Stop the Server
3. . Stop the SAP HANA Instance
1. Change u er to the < id>adm and top HANA:
su - <sid>adm
HDB stop
2. Check the SAP HANA In tance tatu , it mu t be “GRAY, Stopped”.
Plea e note that HANA hutdown take ome time.
sapcontrol –nr <instance no> -function GetProcessList
3.2. Power off the server
Power off the erver. U e the following command on terminal:
shutdown –h now
4. Additional information
For additional information about the hardware plea e review the “U er’ guide” for A2040d
available at www.58 upport.nec.co.jp/global/download
Other manuals for NEC Express5800 Series
107
Table of contents
Other NEC Server manuals
NEC
NEC NEC Express5800 Series Reference guide
NEC
NEC Express5800/B110d User manual
NEC
NEC Express5800/320Ma How to use
NEC
NEC Univerge SV9100 User manual
NEC
NEC Express5800/120Mc2 series User manual
NEC
NEC NEC Express5800 Series User manual
NEC
NEC Express5800/GT110e-S User manual
NEC
NEC EXP805 User manual
NEC
NEC EXPRESS5800/120Ef User manual
NEC
NEC Express5800/T110h User manual
NEC
NEC Express5800/T110g-S User manual
NEC
NEC NP-90MS01 User manual
NEC
NEC Express5800/R120f-2M User manual
NEC
NEC US110 User manual
NEC
NEC LE2200 User manual
NEC
NEC R120d-2E User manual
NEC
NEC Express5800/320Fd-LR User manual
NEC
NEC Express5800/120Rf-2 Instruction Manual
NEC
NEC Express5800/R120h-2M Operating manual
NEC
NEC EXP200 User manual
