National Instruments IC-317 Series User manual

National Instruments IC-3173 Manual

Get Pricing & Availability at

ApexWaves.com

Call Today: 1-800-915-6216

Email: sales@apexwaves.com

https://www.apexwaves.com/modular-systems/national-instruments/industrial-controllers/IC-3173

USER MANUAL

IC-317x

Industrial Controller with Reconfigurable I/O

This document describes the features of the National Instruments IC-317x and contains

information about mounting and operating the device.

Contents

IC-3171, IC-3172, and IC-3173................................................................................................1

About the IC-317x............................................................................................................ 1

Hardware Overview.......................................................................................................... 2

Mounting the IC-317x.....................................................................................................21

IC-3173 (IP67)........................................................................................................................ 27

About the IC-3173 (IP67)............................................................................................... 27

Hardware Overview........................................................................................................ 28

Mounting the IC-3173 (IP67)......................................................................................... 45

Software Options.....................................................................................................................48

IEEE 1588 Precision Time Protocol References.....................................................................49

BIOS Configuration and System Recovery............................................................................ 49

Entering BIOS Setup.......................................................................................................49

BIOS Setup Utility Keyboard Navigation...................................................................... 49

Main Setup Menu............................................................................................................50

Advanced Menu.............................................................................................................. 51

Boot Menu.......................................................................................................................53

Save & Exit Menu...........................................................................................................54

Restoring the NI Linux Real-Time Operating System....................................................55

Restoring the Windows Operating System..................................................................... 55

Where to Go Next................................................................................................................... 57

Resources for LabVIEW Users.......................................................................................57

Resources for Vision Builder AI Users...........................................................................57

Worldwide Support and Services............................................................................................ 57

IC-3171, IC-3172, and IC-3173

The following information applies to the IC-3171, IC-3172, and IC-3173.

About the IC-317x

The IC-317x is a high-performance, small, fanless embedded computer designed for rugged

industrial applications. The IC-317x also provides multiple digital input/output (I/O) options

for communicating with external devices.

Figure 1. IC-317x Block Diagram

Intel Dual-Core Processor

i7-5650U, i5-5350U,

or Celeron 3765U

Xilinx

Kintex-7 FPGA

7K160T

IC-317x

Hardware

Data

x2 DisplayPort

8/4 GB DDR3L

Memory

64/32/4 GB

Solid-state Drive

RJ50 Serial Port

RS-232/422/485

x8 TTL I/O

x2 RS-422 I/O

x8 Isolated

Outputs

x8 Isolated

Inputs

RJ45 Primary Gigabit

Ethernet Port

x2 USB 3.0

Host Ports

x4 USB 2.0

Host Ports

x4 RJ45 Gigabit

Ethernet Ports with PoE

2 GB DDR3L

Memory

4.5 MB

QDR-II+ SRAM

PCI Express

Switch

44-pin D-sub

IC-3173 Only

PCIe

Gen 2

PCIe

Gen 2

Hardware Overview

The IC-317x front panel consists of four Gigabit Ethernet ports with Power over Ethernet

(PoE), one RS-232/RS-485 serial port, one standard Gigabit Ethernet Port, two USB 3.0 ports,

four USB 2.0 ports, and two DisplayPort connectors.

The IC-317x front panel also includes LEDs for communicating system status and a 44-pin

Digital I/O port. The Digital I/O port offers 8 isolated inputs, 8 isolated outputs, 2 bidirectional

differential I/O (RS-422) or single-ended input lines that can be used with a quadrature

encoder, and 8 bidirectional TTL lines.

2| ni.com | IC-317x User Manual

Figure 2. IC-317x Front Panel

POWER

PoE1

PoE2

PoE3

PoE4

DIO

STATUS

USER1

USER FPGA1

ACT/

LINK

10/10 0/

1000

1. DisplayPort Connectors

2. LED Indicators

3. Power over Ethernet (PoE) LED Indicators

4. Gigabit Ethernet Ports with PoE

5. 44-pin Digital I/O Connector

6. Isolated Power Input Connector

7. Chassis Grounding Screw

8. Reset Button (not pictured)

9. Power Button

10. System Power Connector

11. User-Accessible Battery Compartment (not

pictured)

12. RS-232/RS-485 Serial Port

13. USB 3.0 Ports

14. Primary Gigabit Ethernet Port

15. Retention Mounts for USB 3.0 Ports

16. Retention Mounts for USB 2.0 Ports

17. USB 2.0 Ports

Connector Pinouts

The IC-317x provides the following connectors.

DisplayPort

Use the DisplayPort connectors to connect one or more monitors to implement a local HMI for

your controller. You can develop a single real-time VI to use for both your user interface and

system logic. For more information, refer to the Using the Embedded UI to Access RT Target

IC-317x User Manual | © National Instruments | 3

VIs topic in the LabVIEW Help. For up-to-date information about supported NI cables and

accessories, refer to the pricing section of the product page at ni.com.

Use an appropriate adapter cable to connect a DisplayPort connector to a VGA or DVI

connector. The following figure lists the DisplayPort pins and signals.

Figure 3. DisplayPort Connector Pin Locations (IP20)

19 20

Table 1. DisplayPort Connector Pin Descriptions

Pin Signal Name

1 ML_Lane0(p)

2 GND

3 ML_Lane0(n)

4 ML_Lane1(p)

5 GND

6 ML_Lane1(n)

7 ML_Lane2(p)

8 GND

9 ML_Lane2(n)

10 ML_Lane3(p)

11 GND

12 ML_Lane3(n)

13 CONFIG1

14 CONFIG2

15 AUX CH (p)

16 GND

17 AUX CH (n)

18 Hot Plug Detect

4| ni.com | IC-317x User Manual

Table 1. DisplayPort Connector Pin Descriptions (Continued)

Pin Signal Name

19 Return

20 DP_PWR

Ethernet Ports

The IC-317x provides one standard Gigabit Ethernet network port and four Gigabit Ethernet

ports with Power over Ethernet (PoE). The Ethernet ports provide a connection between the

IC-317x, a network, and other Ethernet devices. The IC-317x automatically detects the speed

of the connection and configures itself accordingly.

If a PoE-capable device is plugged into an Ethernet port with PoE, the IC-317x automatically

supplies power to the device. When the IC-317x supplies PoE, the LED that corresponds to the

port illuminates. When you unplug a PoE device, PoE is automatically disabled. You can use

non-PoE Ethernet devices with PoE-enabled Gigabit Ethernet ports.

A CAT 5e or CAT 6 1000Base-T Ethernet cable is required to achieve 1,000 Mbps (Gigabit)

Ethernet performance. CAT 5 Ethernet cables are not guaranteed to meet the necessary

requirements. While CAT 5 cables may appear to work at 1,000 Mbps, CAT 5 cables can cause

bit errors, resulting in degraded or unreliable network performance.

(Windows only) The network Ethernet port provides Wake-on-LAN functionality from the

power off state when associated with the Intel® driver. Wake-on-LAN must be enabled in the

Power Management tab of the Intel I210 Gigabit Network Connection Properties dialog for the

primary Ethernet port in Device Manager. The NI GigE Vision driver (NI-GEV) does not

support Wake-on-LAN. The Ethernet ports with PoE do not support Wake-on-LAN.

Figure 4. Ethernet Port Pin Locations (IP20)

IC-317x User Manual | © National Instruments | 5

Table 2. Ethernet Port Pin Descriptions

Pin Fast Ethernet (100 Mbps) Gigabit Ethernet

MDI MDI-X

1 TX+ BI_DA+ BI_DB+

2 TX- BI_DA- BI_DB-

3 RX+ BI_DB+ BI_DA+

4 No Connect BI_DC+ BI_DD-

5 No Connect BI_DC- BI_DD-

6 RX- BI_DB- BI_DA-

7 No Connect BI_DD+ BI_DC+

8 No Connect BI_DD- BI_DC-

Digital I/O

The 44-pin Digital I/O port on the IC-317x offers 8 isolated inputs, 8 isolated outputs, 2

bidirectional differential inputs (RS-422) or single-ended input lines that can be used with a

quadrature encoder, and 8 bidirectional TTL lines. The Digital I/O port can be connected to

any appropriate shielded device or connector block using a shielded cable.

NI recommends the following digital I/O cables for the IC-317x.

Cable Part Number

44-pin D-sub male to pigtail cable 156083-03 for 3 meter cable

44-pin D-sub male to 44-position D-sub female cable 156084-03 for 3 meter cable

156084-0R5 for 0.5 meter cable

Refer to the following image and table for pin locations and descriptions.

Figure 5. 44-pin Digital I/O Connector Pin Locations (IP20)

6| ni.com | IC-317x User Manual

Table 3. Digital I/O Pin Descriptions

Pin Number Signal Description

1 Diff 0+ Bidirectional RS-422 I/O (positive side), or quadrature encoder

phase A+

2 GND Digital ground reference for TTL and differential I/O

3 TTL 0 Bidirectional TTL I/O

4 TTL 1 Bidirectional TTL I/O

5 GND Digital ground reference for TTL and differential I/O

6 TTL 2 Bidirectional TTL I/O

7 TTL 3 Bidirectional TTL I/O

8 GND Digital ground reference for TTL and differential I/O

9 Diff 1+ Bidirectional RS-422 I/O (positive side), or quadrature encoder

phase B+

10 VISO Isolated power voltage reference output

11 CISO Common ground reference for isolated inputs and outputs

12 Iso Out 0 General purpose isolated input

13 Iso Out 1 General purpose isolated input

14 CISO Common ground reference for isolated inputs and outputs

15 Iso Out 4 General purpose isolated output

16 Diff 0- Bidirectional RS-422 I/O (negative side), or quadrature encoder

phase A-

17 GND Digital ground reference for TTL and differential I/O

18 TTL 4 Bidirectional TTL I/O

19 TTL 5 Bidirectional TTL I/O

20 GND Digital ground reference for TTL and differential I/O

21 TTL 6 Bidirectional TTL I/O

22 TTL 7 Bidirectional TTL I/O

23 GND Digital ground reference for TTL and differential I/O

24 Diff 1- Bidirectional RS-422 I/O (negative side), or quadrature encoder

phase B-

25 VISO Isolated power voltage reference output

IC-317x User Manual | © National Instruments | 7

Table 3. Digital I/O Pin Descriptions (Continued)

Pin Number Signal Description

26 CISO Common ground reference for isolated inputs and outputs

27 Iso Out 2 General purpose isolated output

28 Iso Out 3 General purpose isolated output

29 CISO Common ground reference for isolated inputs and outputs

30 Iso Out 5 General purpose isolated output

31 Iso In 0 General purpose isolated input

32 iso In 1 General purpose isolated input

33 CISO Common ground reference for isolated inputs and outputs

34 Iso In 2 General purpose isolated input

35 Iso In 3 General purpose isolated input

36 CISO Common ground reference for isolated inputs and outputs

37 Iso In 4 General purpose isolated input

38 Iso In 5 General purpose isolated input

39 CISO Common ground reference for isolated inputs and outputs

40 Iso In 6 General purpose isolated input

41 Iso In 7 General purpose isolated input

42 CISO Common ground reference for isolated inputs and outputs

43 Iso Out 6 General purpose isolated output

44 Iso Out 7 General purpose isolated output

Wiring an Isolated Input

You can wire an isolated input to a sourcing output device.

8| ni.com | IC-317x User Manual

Caution Do not allow the voltage on the isolated inputs to exceed 30 VDC. Doing

so will damage the IC-317x.

Figure 6. Connecting an Isolated Input to a Sourcing Output Device

VREF

CISO

Industrial Controller

Input

Sourcing

Output

Device

Current

Limiter

Power Supply

–

Wiring an Isolated Output

The digital isolated output circuits source current to external loads.

When an inductive load, such as a relay or solenoid, is connected to an output, a large counter-

electromotive force may occur at switching time due to energy stored in the inductive load.

This flyback voltage can damage the outputs and the power supply.

To limit flyback voltages at the inductive load, install a flyback diode across the load. Mount

the flyback diode as close to the load as possible. Use this protection method if you connect

any of the isolated outputs on the IC-317x to an inductive load.

The following image shows an example of an isolated output wired to an external load with a

flyback diode installed across the load.

IC-317x User Manual | © National Instruments | 9

This manual suits for next models

Table of contents

Other National Instruments Controllers manuals

National Instruments

National Instruments FlexRIO NI-7931R User manual

National Instruments

National Instruments CompactRIO cRIO-9072 User manual

National Instruments

National Instruments NI PXIe-8840 User manual

National Instruments

National Instruments DAQ-STC Series Product manual

National Instruments

National Instruments NI cRIO-9024 User manual

National Instruments

National Instruments PXI Series User manual

National Instruments

National Instruments NI 9683 User manual

National Instruments

National Instruments cRIO-9032 User manual

National Instruments

National Instruments PXIe-8820 User manual

National Instruments

National Instruments PXI-8186 User manual

National Instruments

National Instruments sbRIO-9629 Owner's manual

National Instruments

National Instruments cRIO-9033 User manual

National Instruments

National Instruments NI PXI-6653 User manual

National Instruments

National Instruments PXI-8186 User manual

National Instruments

National Instruments GPIB-SCSI-A User manual

National Instruments

National Instruments cDAQ-9139 User manual

National Instruments

National Instruments NI SMD-7613 User manual

National Instruments

National Instruments cRIO-9032 User manual

National Instruments

National Instruments IC-3120 User manual

National Instruments

National Instruments sbRIO-9638 User manual

National Instruments

National Instruments PXI-8820 User manual

National Instruments

National Instruments PCI-GPIB User manual

National Instruments

National Instruments Compact FieldPoint cFP-21 Series User manual

National Instruments

National Instruments NI PXIe-8133 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual