MSI MS-7010 User manual

1-1

Getting Started

Chapter 1. Getting

Started

Thank you for purchasing the MS-7010 v1.X Micro ATX

mainboard. The MS-7010 is based on VIA®K8T800 North

Bridge & VT8237 South Bridge and provides eight USB 2.0

ports for high-speed data transmission, C-Media 9761 audio

codec for 6-channel audio output, and a SPDIF interface for

digital audio transmission. Designed to fit the advanced AMD®

Athlon64processors, the MS-7010 delivers a high performance

and professional desktop platform solution.

Getting Started

1-2

MS-7010 M-ATX Mainboard

Mainboard Specifications

CPU

hSupports 64-bit AMD®Athlon64 processor (Socket 754)

hSupports up to 3200+, 3400+, or higher CPU

Chipset

hVIA®K8T800 chipset

- HyperTransportTM connection to AMD Athlon64 processor

- 8 or 16 bit control/address/data transfer both directions

- 800/600/400/200 MHz “Double Data Rate” operation both direction

- AGP v3.0 compliant with 8x transfer mode

hVIA®VT8237chipset

- Integrated Faster Ethernet LPC

- Integrated Hardware Sound Blaster/Direct Sound AC97 audio

- Ultra DMA 66/100/133 master mode PCI EIDE controller

-ACPI

- Supports 2 Serial ATA ports

- Supports 8 USB2.0 ports

MainMemory

hSupports DDR266/333/400 DDR SDRAM for two 184-pin DDR DIMMs

hSupportsamaximummemorysizeof2GB

Slots

hOne (Accelerated Graphics Port) AGP slot

- AGP 3.0 specification compliant(1.5Vfor2X/4X/8X)

hThree 32-bit Master 3.3v/5v PCI Bus slots

hOne mini PCI slot

On-Board IDE

hAn IDE controller on the VIA®VT8237 chipset provides IDE HDD/CD-

ROM with PIO, Bus Master and Ultra DMA 66/100/133 operation modes

hCan connect up to 4 IDE devices

hSerial ATA/150 controller integrated by VT8237

- Up ot 150MB/s transfer rate

- Can connect up to 2 serial ATA devices

1-3

Getting Started

IEEE1394 (Optional)

hSupports up to 2 * 1394 ports (up to 400Mbps transfer rate)

hControlled by VIA VT6307 chipset

On-BoardPeripherals

hOn-Board Peripherals include:

- 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and

2.88Mbytes

- 1 serial port (COMA)

- 1 parallel port supports SPP/EPP/ECP mode

- 8 USB ports (Rear * 4/Front * 4)

- 2 IEEE 1394 ports (Rear * 1/Front * 1)

- 1 audio port

-1 RJ-45LAN jack

Audio

hC-Media 9761 6-channel software audio codec

- Compliance with AC97 v2.3 Spec

- Meet PC2001 audio performance requirement

LAN

hVIA®VT6103EthernetController

- Integrated Fast Ethernet MAC and PHY in one chip

- Supports 10Mbps & 100Mbps

BIOS

hThe mainboard BIOS provides “Plug & Play” BIOS which detects the pe-

ripheral devices and expansion cards of the board automatically.

hThe mainboard provides a Desktop Management Interface (DMI) function

which records your mainboard specifications.

Dimension

hMicro ATX Form Factor: 24.5 cm (L) x 24.5 cm (W)

Mounting

h6 mounting holes

1-4

MS-7010 M-ATX Mainboard

Mainboard Layout

MS-7010 v1.X Micro ATX Mainboard

BATT

DDR1

DDR2

JAUDIO1

JAUDIO2

JWR1

JBAT1

MINIPCI1

BIOS

PCI Slot 3

PCI Slot 2

PCI Slot 1

IDE1

FDD1

IDE2

CFAN1

AGPSlot

JPW1

Codec

JVIDEO1 JF_W1

VIA

VT6307

VIA

VT6103

Winbond

83697THF

JUSB1 JUSB2

JF_P1

VIA

K8T800

Top: LAN Jack

Bottom: USB Ports

Top: 1394 Port

Bottom: USB Ports

Top: Mouse

Bottom: Keyboard

B: Line-Out

Line-Out

T: Mic

B: Line-In

VIA

VT8237

VIA

K8T800

SATA1

SATA2

2-1

Hardware Setup

Chapter 2. Hardware

Setup

This chapter tells you how to install the CPU, memory

modules, and expansion cards, as well as how to setup the jump-

ers on the mainboard. Also, it provides the instructions on con-

necting the peripheral devices, such as the mouse, keyboard,

etc.

While doing the installation, be careful in holding the com-

ponents and follow the installation procedures.

Hardware Setup

2-2

MS-7010 M-ATX Mainboard

Quick Components Guide

BATT

BIOS

VIA

VT8237

JF_W1,p.2-16

J3, p.2-15

DDR DIMMs, p.2-9

CPU, p.2-3

Back Panel

I/O, p.2-12

CFAN1, p.2-15

FDD1, p.2-13

JUSB1/2, p.2-16

JPW1, p.2-11

AGP Slot, p.2-19

JVIDEO1, p.2-14

PCI Slots,p.2-19

IDE1/2, p.2-13

Mini PCI, p.2-19

SATA1/2,p.2-17

JF_P1, p.2-15

JBAT1, p.2-19

JWR1, p.2-11

JAUDIO2, p.2-14

JAUDIO1, p.2-14

2-3

Hardware Setup

Central Processing Unit: CPU

The mainboard supports AMD®Athlon64 processor. The mainboard

uses a CPU socket called Socket-754 for easy CPU installation. When you are

installing the CPU, make sure the CPU has a heat sink and a cooling fan

attached on the top to prevent overheating. If you do not have the heat sink

and cooling fan, contact your dealer to purchase and install them before turn-

ing on the computer.

MSI Reminds You...

Overheating

Overheating will seriously damage the CPU and system, always

make sure the cooling fan can work properly to protect the CPU

from overheating.

Replacing the CPU

While replacing the CPU, always turn off the ATX power supply

or unplug the power supply’s power cord from grounded outlet

first to ensure the safety of CPU.

2-4

MS-7010 M-ATX Mainboard

CPU Installation Procedures for Socket 754

1. Please turn off the power and

unplug the power cord before

installing the CPU.

2. Pull the lever sideways away

from the socket. Make sure

to raise the lever up to a 90-

degree angle.

3. Look for the gold arrow. The

gold arrow should point to-

wards the lever pivot. The

CPU can only fit in the cor-

rect orientation.

4. If the CPU is correctly

installed, the pins should be

completely embedded into the

socket and can not be seen.

Please note that any violation

of the correct installation pro-

cedures may cause permanent

damages to your mainboard.

5. Press the CPU down firmly

into the socket and close the

lever. As the CPU is likely to

move while the lever is being

closed, always close the lever

with your fingers pressing

tightly on top of the CPU to

make sure the CPU is prop-

erly and completely embed-

ded into the socket.

OpenLever

90 degree

Sliding

Plate

Gold

arrow

Gold

arrow

Gold

arrow

C orrect

CPU

placem ent

Incorrect

CPU

placem ent

Lever

Press

dow n

th e C P U

2-5

Hardware Setup

Installing AMD Athlon64 CPU Cooler Set

When you are installing the CPU, make sure the CPU has a heat sink

and a cooling fan attached on the top to prevent overheating. If you do not

have the heat sink and cooling fan, contact your dealer to purchase and install

them before turning on the computer.

1. Detach the shield of the

backplate’s paster.

2. Turn over the mainboard, and

install the backplate to the

proper position.

2-6

MS-7010 M-ATX Mainboard

3. Turn over the mainboard

again, and place the

mainboard on the flat surface.

Locate the two screw holes of

the mainboard.

4. Align the retention mechanism

and the backplate.

Fix the retention mechanism

and the backplate with two

screws.

5. Position the cooling set onto

the retention mechanism.

Hook one end of the clip to

hook first.

retention mechanism

Table of contents

Other MSI Motherboard manuals

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual