Monarch Sierra Sport 2 User manual

MONARCHis a registered trademark of Monarch Marking Systems, Inc. Sierra Sport and 9460 are

trademarks of Monarch Marking Systems, Inc. Paxaris a trademark of Paxar Corporation.

IP PRINTER SETUP

Use these instructions to configure your MONARCHSierra Sport2 IP

Printer using the printer’s Main Menu. The IP printer operates on any WiFi

(Wireless Fidelity) compatible 802.11b RF network. Make sure your access

point and network are correctly set up. Refer to your network manuals for

more information. This manual does not include information about setting up

your RF network.

Setting Up the RF Network Printer

1. Turn on the printer by pressing and holding the Pbutton until the

display turns on.

The display flashes printer version information, battery charging

status, and then you will see:

Ready

p<T>

The <T> on the display indicates the printer is connected to a

network (peer to peer or infrastructure mode). indicates the printer

is not connected to a network.

When you see “Ready,” press the Center navigational button to

display the printer’s IP address. Press any button to return to

Ready mode.

2. Press the Abutton under the picon.

E BF

R XT

You will see the battery indicator E (empty) and F (full). As you use

the printer, the battery indicator line gets closer to E (empty), instead

of F (full). Recharge the battery when the line is by the E.

3. Press the Abutton under the Ticon (Tool Box) to enter the program.

Tool Box

Language

4. Tool Box is highlighted. Press the Abutton under the Eicon to select

Tool Box.

Enter Password

5. Press the navigational buttons in this order: Right, Center, Left,

Center, Right. The Service Diagnostics menu appears.

6. Press the Abutton under Duntil you see

Setup

Service

Eu U D

7. Service is highlighted. Press the Abutton under the Eicon to select

Service.

Totals

Sensor Cal

8. From the Service menu, press the Abutton under Duntil you see RF

Network. Press the Abutton under the Eicon to select RF Network.

The following menu shows the RF Network options.

The RF Network menu allows you to check the printer’s status, configure the

RF network settings, and reset the radio.

To exit, press the Fbutton at any time.

Status Configure Reset Exit

Network

Checking the Status

This option displays the status of the RF network.

1. From the RF Network menu, select Status.

192.168.069.062

S1.10 020 104

Version 1.10

WHSEFLR

The local IP address, firmware version, software version, and device

name are displayed.

2. Press any Abutton to see the next screen of information.

OIKOB1ZO3B54

Protocol: TCP

State: Wait

Radio: IEEE 802.11b

The MAC address, protocol, current state, and radio type are

displayed.

3. Press any Abutton to return to the RF Network menu.

Resetting the RF Network

This option resets the radio, because it cycles the power off and then back

on.

NOTE: You may lose your current connection and application.

1. From the RF Network menu, select Reset.

Reset command

sent. Hit key

to continue.

2. Press any Abutton to return to the RF Network menu.

Configuring the Printer

The following menu shows the RF Network Configure options.

The Configure menu allows you to set the printer’s IP Address, Subnet Mask,

Gateway, Power Mode, Call/Listen, Protocol, Transfer, and ESS ID.

To exit, press the Fbutton at any time.

Setting the IP Address

This option sets the printer’s IP Address.

1. From the RF Network menu, select Configure.

2. From the Configure menu, select IP Address.

IP Address

192.168.69.62

ER+

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the

positions from left to right

Increments the current

position setting by 1

3. When the setting you want is displayed, press the Abutton under the E

icon to save the setting. You return to the Configure menu.

Address

Subnet

Mask

Gateway Power

Mode

Configure

Call/

Listen

Protocol

Transfer ESS ID Exit

Setting the Subnet Mask

This option sets the printer’s Subnet Mask.

1. From the Configure menu, select Subnet Mask.

Subnet Mask

255.255.000.000

ER+

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the positions

from left to right

Increments the current

position setting by 1

2. When the setting you want is displayed, press the Abutton under the E

icon to save the setting. You return to the Configure menu.

Setting the Gateway

This option sets the printer’s Gateway address.

1. From the Configure menu, select Gateway.

Gateway

000.000.000.000

ER+

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the positions

from left to right

Increments the current

position setting by 1

2. When the setting you want is displayed, press the Abutton under the E

icon to save the setting. You return to the Configure menu.

Setting the Power Mode

This option sets the Power Mode.

1. From the Configure menu, select Power Mode.

Power Mode

PP CAM

X PSP

The choices include CAM (continuously awake) or PSP (power save

protocol). PSP conserves battery power. CAM means the printer is

continuously receiving and transmitting data. This mode uses

battery power quickly.

2. Use the Abutton under the Dicon to select the power mode you want.

Press the Abutton under the Eicon to save the setting.

If you select PSP, you are prompted to enter a PSP algorithm

between 1-10. 1 is the shortest sleep time (uses battery power

quicker, but responds faster); 10 is the longest sleep time (optimal

battery conservation, but responds slower).

EUD

3. Use the Abuttons under the Uor Dicons to select the desired PSP

algorithm. Press the Abutton under the Eicon to save the setting.

You return to the Configure menu.

Setting the Call/Listen Mode

This option sets the connection mode to Call or Listen.

1. From the Configure menu, select Call/Listen.

Call/Listen

PP Listen

X Call

The choices include Listen or Call. Call mode initiates the transfer of

data. Call mode can be used for TCP or Telnet protocols. Listen

mode waits for a host to connect to the specified port and receives

data. Listen mode can be used for TCP or LPD protocols.

2. Use the Abutton under the Dicon to select the connection mode you

want. Press the Abutton under the Eicon to save the setting. For

example, if you select Call, you will see

Port

+ 09100

ER+

In Listen mode, this is the listen port.

In Call mode, this is the call port.

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the positions

from left to right

Toggles between +or –;

also

Increments the current

position setting by 1

3. When the setting you want is displayed, press the Abutton under the E

icon to save the setting.

Remote IP

192.168.069.200

ER+

In Call mode, this is the remote IP address you are calling.

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the positions

from left to right

Increments the current

position setting by 1

4. When the remote IP setting you want is displayed, press the Abutton

under the Eicon to save the setting.

5. Press the Fbutton to exit. You return to the Configure menu.

Setting the Protocol

This option sets the protocol.

1. From the Configure menu, select Protocol.

Protocol

PP TCP

X Telnet

EUD

The choices include DLP, UDP, TCP, Telnet, or LPD. The most

common options are TCP and LPD for AS400 or Unix systems. Do

not use UDP.

2. Use the Abuttons under the Uor Dicons to select the protocol you

want. Press the Abutton under the Eicon to save the setting. You

return to the Configure menu.

Setting the Transfer Mode

1. From the Configure menu, select Transfer.

Transfer

PP Stream

X Frame

The choices include Stream or Frame.

2. Use the Abutton under the Dicon to select the transfer mode you

want. Press the Abutton under the Eicon to save the setting.

3. Press the Fbutton to exit. You return to the Configure menu.

Setting the ESS ID

1. From the Configure menu, select ESS ID.

ESS ID

ABC 1234

ERD

Use the Abuttons as shown in the following table:

Press Ato

Saves the setting Scrolls through the positions

from left to right

Increments the current

position setting by 1 and

scrolls through

alpha/special characters

2. When the setting you want is displayed, press the Abutton under the E

icon to save the setting.

3. Press the Fbutton to exit.

When you select “Exit” after configuring, you will see

Configure

Re-configure?

To save all the configuration settings, press the Abutton under the Eicon.

To exit without saving the configuration settings, press the Abutton under

the Xicon.

The IP printer is ready to use. Turn on the printer.

When you see

Ready

p<T>

Press the Abutton under the connected icon <T> to see the printer’s IP

Address. Press any Abutton to toggle back to Ready.

For supplies, service or assistance, call toll free:

1-800-543-6650 (In the U.S.A.)

1-800-263-4650 (In Canada)

www.paxar.com

Other Monarch Printer manuals

Monarch

Monarch 9855 Service manual

Monarch

Monarch 9820 User manual

Monarch

Monarch RASCAL 9450 User manual

Monarch

Monarch 9855 RFMP User manual

Monarch

Monarch 9400 Series Service manual

Monarch

Monarch PATHFINDER Ultra 6030TM Service manual

Monarch

Monarch 9430RX Service manual

Monarch

Monarch 9401 Service manual

Monarch

Monarch 9403 User manual

Monarch

Monarch 9855 Supplement

Monarch

Monarch 9855 Service manual

Monarch

Monarch 9406 Service manual

Monarch

Monarch 9401 Technical Document

Monarch

Monarch 9493 9493 User manual

Monarch

Monarch 9414 User manual

Monarch

Monarch Paxar 9450 RASCAL Service manual

Monarch

Monarch 9855 User manual

Monarch

Monarch MPCL II User manual

Monarch

Monarch Pathfinder Ultra Silver 6032 User manual

Monarch

Monarch 9855 HF User manual

Monarch

Monarch 9460 User manual

Monarch

Monarch 94 Series Operator's manual

Monarch

Monarch 9403 Service manual

Monarch

Monarch Pathfinder Ultra Platinum 6039 User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide