Midea FT30-8MB User manual

READ AND SAVE THESE INSTRUCTIONS

Attention: Pictures in the IM are for reference only.

GD Midea Environment Appliances MFG.Co.,Ltd.

No.28, Dong Fu Road, Hesui East Industrial Area, Dong Feng Town,

Zhongshan, Guangdong 528425 P.R.China

ELECTRIC FAN

MODEL: FT30-8MB

TABLE FAN

OWNER’S MANUAL

Read Rules for Safe Operation and Instructions Carefully.

CAUTION

1. If the supply cord is damaged, it must be replaced by manufacturer

or its service agent or a similarly qualified person in order to avoid

a hazard.

2. To protect against the risk of electrical shock, do not immerse the

unit, cord or plug in water or other liquid.

3. This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a

person responsible for their safety. Young children should be

supervised to ensure that they do not play with the appliance.

4. When the appliance is not in use and before cleaning, unplug the

appliance from the outlet.

5. Keep electrical appliances out of reach from Children or infirm

persons. Do not let them use the appliances without supervision.

6. When the fan was assembled, the rotor blade guard shall not be

taken off anymore

- Prior cleaning unplug the fan.

- The rotor guard shall not be dissembled/opened to clean the

rotor blades.

- Wipe the fan enclosure and rotor blade guard with a slightly

damp cloth.

WARNING

1. Never insert fingers, pencils, or any other object through the

grille when fan is running.

2. Disconnect fan when moving from one location to another.

3. Be sure fan is on a stable surface when operating to avoid

overturning.

4. DO NOT use fan in window, rain may create electrical hazard.

5. Household use only.

RULES FOR SAFE OPERATION

PART FIGURE

1. Front grill

2. Blade

3. Plastic nut

4. Rear grill

5. Motor shaft

6. Oscillating clutch knob

7. Pedestal

8. Screw

9. Spinner

10. Base

11. Nut

12. Piano switch

ASSEMBLY OF BASE

1. Detach screw from base of the fan.

2. Match locking tab to base and click into position.

3. Tighten the screw in the base to secure the fan to the base.

Note: All the pictures in this manual are for explanation

purpose only. Any discrepancy between the real object

and the illustration in the drawing shall be subject to the

real subject.

GRILL & FAN BLADE ASSEMBLY

1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the

plastic nut counterclockwise to remove both of them. Fix the rear grill to the

motor then tighten the plastic nut again. (Fig.1)

2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove

of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig.2)

3. Open the clips on the Front Guard and place the Front Guard onto the

Rear Guard (align the locking screw holes) and close clips. Secure both

guards firmly by fitting and tightening the locking screw and nut. (Fig.3)

182311

Handle

Motor

tighten

loosen 10

Spinner Spinner

tighten

Groove

Stopper Pin

loosen

Plastic Nut

Fig.1 Fig.2 Fig.3

Blade

Speed control

Speed is controlled by the piano switch. (0-1-2-3)

0--Off 1--Low 2---Medium 3---High

Oscillation control

To make the fan oscillate, push down on the oscillating clutch knob located on the

top of the motor housing.

To stop the fan down from oscillating in the position desired, push on the oscillating

clutch knob once more.

Tilting control

To adjust the air flow upward or downward, push the grilles lightly to the desired

direction.

OPERATION INSTRUCTION

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified

service personnel if service is needed.

1. Before cleaning and assembling, fan must be unplugged.

2. To ensure adequate air circulation to the motor, keep vents at the rear of the

motor free of dust. Do not disassemble the fan to remove dust.

3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.

4. Do not use any abrasive detergent or solvents to avoid scratching the surface.

Do not use any of the following as a cleaner: gasoline, thinner.

5. Do not allow water or any other liquid into the motor housing or interior parts.

MAINTENANCE INSTRUCTION

CLEANING

1. Be sure to unplug from the electrical supply source before cleaning.

2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.

Thoroughly remove soap film with dry cloth.

DISPOSAL：Do not dispose of electrical appliances as unsorted

municipal waste, use separate collection facilities. Contact your

local government for information regarding the collection systems

available. If electrical appliances are disposed of in landfills or dumps, hazardous

substances can leak into the groundwater and get into the food chain, damaging

your health and well-being.

Table of contents

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual