Linksys WPC55AG User manual

A Division of Cisco Systems, Inc.

Model No.

Quick Installation Guide

Model No.

Quick Installation Guide

WPC55AG (EU/LA/UK)

Notebook Adapter

Wireless A+G

Package Contents

• Dual-Band Wireless A+G Notebook Adapter

• Setup CD-ROM

• User Guide (English only) on CD-ROM

• Quick Installation

Dual-Band

GHz

802.11a

5GHz

802.11g

AInsert the Setup Wizard CD-

ROM into your CD-ROM drive.

The Setup Wizard should run

automatically, and the

Welcome screen should

appear. If it does not, click the

Start button and choose Run.

In the field that appears, enter

D:\setup.exe (if “D” is the letter

of your CD-ROM drive).

BTo install the Adapter, click the

Install button on the Welcome

screen.

CAfter reading the License

Agreement, click Next to

accept the agreement

DChoose a network type. Select

5GHz or 2.4GHz if you will

connect to 802.11a, 802.11g,

and/or 802.11b networks.

Select 5GHz only if you will

connect only to 802.11a

networks. Select 2.4GHz only if

you will connect only to

802.11g and/or 802.11b

networks. Then click Next.

EChoose a wireless network

mode. Click the Infrastructure

Mode radio button if you want

your wireless computers to

network with computers on

your wired network using a

wireless access point. Click the

Set up the Dual-Band Wireless A+G

Notebook Adapter

IMPORTANT: You must run the

Setup Wizard before inserting the

Adapter into your notebook

computer.

Ad-Hoc Mode radio button if

you want multiple wireless

computers to network directly

with each other.

In the SSID field, enter the SSID

or name for your wireless

network. The SSID must be

identical for all devices in the

network. Click Next.

FIf you chose Infrastructure

Mode, go to Step G now.

Select the correct operating

channel for your wireless

network, which must match the

channel set on the other

devices in your wireless

network. If you are unsure

about which channel to use,

keep the default setting, Auto.

Then, click Next.

GSelect the security method you

want to use: WEP, WPA-

Personal, WPA-Enterprise,

RADIUS, or LEAP. Then click

Next.

If your network doesn’t use any

security method, select

Disabled and click Next. Then

proceed to Step I.

NOTE: WEP stands for Wired

Equivalent Privacy. WPA stands

for Wi-Fi Protected Access and is

a stronger security method than

WEP. RADIUS stands for Remote

Authentication Dial-In User

Service, and LEAP stands for

Lightweight Extensible

Authentication Protocol.

HProceed to the appropriate

instructions for your security

method.

1WEP

aSelect 64-bit, 128-bit, or 152-

bit from the drop-down menu

(152-bit encryption is available

only for 802.11a networking).

bEnter your Passphrase in the

Passphrase field, and the WEP

key will be automatically

generated.

To manually enter the WEP key,

leave the Passphrase field

blank and enter the WEP key in

the WEP Key field.

cClick Next, and go to Step I.

2 WPA - Personal

aSelect the encryption method

you want to use, TKIP or AES,

from the drop-down menu.

bEnter your Passphrase or pre-

shared key in the Passphrase

field.

cThen click Next and proceed

to Step I.

WEP

WPA - Personal

3 WPA-Enterprise

Select the authentication method

you want to use, EAP-TLS or PEAP.

EAP-TLS

aEnter the login name in the

bEnter the name of the

authentication server in the

Server Name field. (optional)

cFrom the Certificate drop-

down menu, select the

authentication certificate.

dSelect the encryption method

you want to use, TKIP or AES.

eClick Next, and go to Step I.

PEAP

aEnter the login name in the

bEnter the password in the

Password field.

cEnter the name of the

authentication server in the

Server Name field. (optional)

dFrom the Certificate drop-

down menu, select the

authentication certificate.

eSelect the authentication

method used inside the PEAP

tunnel, EAP-MSCHAP v2 or

Generic Token Card.

WPA - Enterprise

EAP-TLS

WPA - Enterprise

PEAP

fSelect the encryption method

you want to use, TKIP or AES.

gClick Next, and go to Step I.

4 RADIUS

Select the authentication method

you want to use, EAP-TLS or PEAP.

EAP-TLS

aEnter the login name in the

bEnter the name of the

authentication server in the

Server Name field. (optional)

cFrom the Certificate drop-

down menu, select the

authentication certificate.

dClick Next, and go to Step I.

PEAP

aEnter the login name in the

bEnter the password in the

Password field.

cEnter the name of the

authentication server in the

Server Name field. (optional)

dFrom the Certificate drop-

down menu, select the

authentication certificate.

eSelect the authentication

method used inside the PEAP

RADIUS

EAP-TLS

RADIUS

PEAP

ftunnel, EAP-MSCHAP v2 or

Generic Token Card.

gClick Next, and go to Step I.

5 LEAP

aEnter the user name in the User

Name field.

bEnter your password in the

Password field.

cEnter your password again in

the Confirm field.

dClick Next, and go to Step I.

IThe Setup Wizard will ask you to

review your settings before it

starts to copy files. Click Next to

save these settings, or click

Back to change any settings.

JIf you are using Windows 2000,

you may see a screen

indicating that a digital

signature was not found. This

software has been tested and

works properly with Windows

2000. Click the Yes button.

KAfter the software has been

successfully installed, the

Congratulations screen will

appear. Click Exit.

LEAP

APower down your notebook

and locate an available

CardBus slot on it.

BWith the connector pin end

facing the CardBus slot and

the label facing up, slide the

Adapter into the CardBus slot

until it locks into place.

CPower on your notebook

computer. The Power LED

should light up when the

Adapter is installed correctly.

DIf you are using Windows 2000,

you may see a screen

indicating that a digital

signature was not found. This

software has been tested and

works properly with Windows

2000. Click the Yes button.

EAfter the Adapter is installed,

the Wireless Network Monitor

icon will appear in the system

tray at the bottom right-hand

corner of your screen.

Double-click the icon if you

want to check the link

information, search for

available wireless networks, or

make additional configuration

changes.

Congratulations! The installation of

the Dual-Band Wireless A+G

Notebook Adapter is complete.

WPC55AG-EU-LA-UK_V1.2-QIG-50110NCJL

Linksys is a registered trademark or trademark of

Cisco Systems, Inc. and/or its affiliates in the U.S.

Connect the Dual-Band

Wireless A+G Notebook Adapter

For additional information or troubleshooting

help, refer to the User Guide on the CD-ROM

or the Technical Support Insert. You can also

e-mail for further support.

Website

http://www.linksys.com/international

A Division of Cisco Systems, Inc.

Modelnr.

Installationsvejledning

Modelnr.

Installationsvejledning

WPC55AG (DK)

Notebook-netværkskort

Trådløs-A+G

Pakkens indhold

• Trådløst dual band-A+G-Notebook-netværkskort

• Installations-cd-rom

• Brugervejledning (kun på engelsk) på cd-rom

• Installationsvejledning

Dual band

GHz

802.11a

GHz

802.11g

APlacer cd-rom'en med guidet

konfiguration i cd-rom-drevet.

Den guidede konfiguration

køres automatisk, og

skærmbilledet Welcome

(Velkommen) vises. Hvis det

ikke er tilfældet, skal du klikke

på knappen Start og vælge

Kør. Indtast D:\setup.exe i det

felt, der vises (hvis "D" er

bogstavet for cd-rom-drevet).

BInstaller kortet ved at klikke på

knappen Install (Installer) i

skærmbilledet Welcome

(Velkommen).

CKlik på Next (Næste), når du

har læst licensaftalen, for at

acceptere vilkårene.

DVælg en netværkstype. Vælg

5GHz or 2.4GHz (5 GHz eller

2,4 GHz) for at tilslutte 802.11a-,

802.11g- og/eller 802.11b-

netværk. Vælg 5GHz only (Kun

5 GHz) for kun at tilslutte

802.11a-netværk. Vælg

2.4GHz only (Kun 2,4 GHz) for

kun at tilslutte 802.11g- og/eller

802.11b-netværk. Klik derefter

på Next (Næste).

EVælg en tilstand for det

trådløse netværk. Klik på

alternativknappen

Infrastructure Mode,

(Infrastrukturtilstand), hvis dine

trådløse computere, skal

oprette netværksforbindelse til

Konfiguration af det trådløse dual

band-A+G-Notebook-netværkskort

VIGTIGT: Du skal køre den

guidede konfiguration, inden du

sætter netværkskortet i din

notebook-computer.

Other manuals for WPC55AG

Table of contents

Languages:

Popular Adapter manuals by other brands

PCB Piezotronics

PCB Piezotronics 090B274 Installation and operating manual

Auvidea

Auvidea J20 Technical reference manual

Gossen MetraWatt

Gossen MetraWatt AT3-III E operating instructions

Akribis

Akribis ITF-21-BISS-MIT user manual

Tenda

Tenda W54U user guide

ROHO

ROHO AGILITY Operation manual

PROLiNK

PROLiNK WN2001 Quick installation guide

Hawking

Hawking HUF2 Specifications

Airlink101

Airlink101 AWLC4030 user manual

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter user manual

Philips

Philips SWA4554S/10 user manual

JVC

JVC TS-C9D2B Assembly and installation instructions

NETGEAR

NETGEAR A6100 quick start

D-Link

D-Link DWA-121 Quick install guide

Philips

Philips SWA2037 Specifications

Basalte

Basalte 0610-20 installation manual

Yealink

Yealink EHS40 user guide

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A installation guide