Linear Technology LT3473EDD User manual

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 883

LI-ION TO 25V STEP-UP DC-DC CONVERTER

LT3473EDD

DESCRIPTION

Demonstration circuit DC883 features the LT®3473

micropower step-up DC/DC converters with inte-

grated Schottky diode and output disconnect cir-

cuitry. The output on DC883 is 25V at up to 80mA

from a 3~4.2V input, while automatic Burst Mode op-

eration maintains efficiency at light load. The lithium

ion battery input voltage range, high output voltage,

internal NPN power switch, minimal external compo-

nents and simple design make the LT3473 an excel-

lent solution for OLED and CCD Bias.

The DC883 has a jumper for enabling the output

(JP2). Placing the jumper to “OFF”, disables the DC-

DC converter and jumper to “ON”, enables the DC-DC

converter. There is a jumper (JP1) and a control pin

(CTRL) for varying the output voltage. Placing the

jumper to “VIN” provides 25V output. Placing the

jumper to “CTRL” and changing the voltage at CTRL

pin can change the output voltage. The voltage of the

PGOOD pin is approximately 0V as the output voltage

reaches 90% of final value.

Design files for this circuit board are available. Call

the LTC factory.

LT is a registered trademark of Linear Technology Corporation

Table 1.

Performance Summary ( TA= 25°

°°

°C )

PARAMETER CONDITION VALUE

Minimum Input Voltage 3V

Maximum Input Voltage 4.2V

Maximum Output Current Vin = 3 − 4.2V 80mA

Typical Switching Frequency 1.2MHz

QUICK START PROCEDURE

Demonstration circuit 883 is easy to set up to evalu-

ate the performance of the LT3473. Refer to Figure 1.

for proper measurement equipment setup and follow

the procedure below:

1. Set the input supply between 3V to 4.2V.

With power off, connect the input power sup-

ply to VIN and GND. Make sure JP2 is set to

“ON” and JP1 is set to “VIN”.

2. Turn on the power at the input.

3. The output voltage should measure about 25V

across the “VOUT” terminal to “GND” terminal

and the voltage across the PGOOD pin and

“GND” terminal should measure about 0V.

4. Test the shutdown function by placing JP2 to

“OFF”. Observe the output voltage is about

0.7V lower than the input voltage.

5. The output voltage can be controlled by DC

voltage at the CTRL terminal. With JP2 placed

at “ON” and JP1 placed at “CTRL”, observe

the output voltage change with DC voltage

applied to the CTRL terminal. The DC voltage

range recommended is 200mV ~ 1.5V. The

maximum DC voltage is 10V. Refer to the

datasheet for further details.

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 883

LI-ION TO 25V STEP-UP DC-DC CONVERTER

AVV

Load

+++

Figure 1. Proper Measurement Equipment Setup

Figure 2. Scope Probe Placement for Measuring Input or Output Ripple

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 883

LI-ION TO 25V STEP-UP DC-DC CONVERTER

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

DC883A

Other Linear Technology Motherboard manuals

Linear Technology

Linear Technology LTC5584 User manual

Linear Technology

Linear Technology DC1338A Quick setup guide

Linear Technology

Linear Technology DC1816B User manual

Linear Technology

Linear Technology DC1472A Quick setup guide

Linear Technology

Linear Technology DC2347A Quick setup guide

Linear Technology

Linear Technology DC2049A Quick setup guide

Linear Technology

Linear Technology Analog Devices DC1890A Quick setup guide

Linear Technology

Linear Technology DC1962C Quick setup guide

Linear Technology

Linear Technology LTC2374 Quick setup guide

Linear Technology

Linear Technology DC102 Quick setup guide

Linear Technology

Linear Technology DC2077A Quick setup guide

Linear Technology

Linear Technology DC2016A Quick setup guide

Linear Technology

Linear Technology DC1537A Quick setup guide

Linear Technology

Linear Technology DC2142A Quick setup guide

Linear Technology

Linear Technology DC1763A Quick setup guide

Linear Technology

Linear Technology LTC4245CUHF User manual

Linear Technology

Linear Technology DC1398 User manual

Linear Technology

Linear Technology DC1317A User manual

Linear Technology

Linear Technology DC2026A Quick setup guide

Linear Technology

Linear Technology Analog Devices DC2688A Quick setup guide

Linear Technology

Linear Technology DC1668A-A Quick setup guide

Linear Technology

Linear Technology DC2475A-A Quick setup guide

Linear Technology

Linear Technology DC2181A Series Quick setup guide

Linear Technology

Linear Technology DC1385A Quick setup guide

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual