Linear Technology DC299 User manual

DC299 Introduction

Description

Demo board DC299 features the LTC1729 Li-Ion charge-termination IC in combination with the

LT1769 battery charger IC. This board provides a complete solution for charging 1- or 2-cell Li-

Ion batteries with a 2A charging current. These ICs have end-of-charge termination that can be

configured to stop the charger when the charge current drops below 10% of its initial setting or

when the internal timer counts to 3 hours. A safety termination feature disables charging if the

temperature is below 0°C or above 50°C and resumes charging when the temperature returns to

the 0°C to 50°C range. The solution extends battery life by trickle charging when the battery is

depleted and by meeting the battery manufacturers’voltage requirement of 1% total accuracy.

Finally, the board adds convenience by automatically detecting when a battery or supply is

present.

This board is intended for designers who need the versatility of battery charger DC/DC

converters. The small size and efficiency of this circuit allow it to function in portable

applications as well as in wall operated chargers.

Quick Start Guide

It is simple to set up the DC299 demo board to charge a 1-cell or 2-cell Li-Ion battery. Follow the

procedure outlined below for proper operation. Note: Use the battery manufacturer’s

recommended safety procedures and protection circuits.

–

'SCOPE

BATTERY

TO BE

CHARGED

SYSTEM

LOAD

GND

UV OUT

PROGRAM

VBAT

GND

NTC

GND

+VIN

LT1769CGN/LTC1729CMS8

2A Li-Ion Battery Charger

With Termination Controller

Demo Circuit DC299A

]

LED

]

C/10

]

3HR

JP1

Figure 1. DC299 Connection Diagram

1. The demo board comes in four versions, each with a different output voltage. It is very

important to determine the correct version for your battery. To verify the output voltage of the

board, compare the marking on the top of U2 (refer to Figure 1) with Table 1.

2. Before turning on power, connect the input power supply, battery, oscilloscope and meters as

shown in Figure 1. For best accuracy, it is important to connect voltmeters directly to the PCB

terminals when measuring input and output voltages.

3. Select the end-of-charge termination method desired. If 3-hour termination is preferred,

connect two jumpers on JP1, enabling LED and 3HR. To stop the charger after the current

drops below 10% of 2A or 200mA, connect the jumper on JP1 to enable C/10.

4. The charger can be stopped if the temperature is not in the 0°C to 50°C range using the NTC

terminal on the PCB board. An external 10k NTC thermistor, such as a Vishay

NTHS12106N02, must be connected between the NTC terminal and ground and R14 must be

removed from the PCB board.

1elbaT

gnikraMtraPegatloVnoisreVylbmessA

YLTLV1.4A-

HJTLV2.4B-

ZLTLV2.8C-

GJTLV4.8D-

Table of contents

Other Linear Technology Motherboard manuals

Linear Technology

Linear Technology DC1962C Quick setup guide

Linear Technology

Linear Technology DC1762A Quick setup guide

Linear Technology

Linear Technology DC2491A Quick setup guide

Linear Technology

Linear Technology LTC5585 User manual

Linear Technology

Linear Technology DC1238B User manual

Linear Technology

Linear Technology LTC2270 Quick setup guide

Linear Technology

Linear Technology DC1755A Quick setup guide

Linear Technology

Linear Technology DC2194A Quick setup guide

Linear Technology

Linear Technology DC1816B Quick setup guide

Linear Technology

Linear Technology DC1877A Quick setup guide

Linear Technology

Linear Technology DC1763A Quick setup guide

Linear Technology

Linear Technology DC1759A Quick setup guide

Linear Technology

Linear Technology DC1505A Quick setup guide

Linear Technology

Linear Technology DC1830A-A Quick setup guide

Linear Technology

Linear Technology DC2133A Quick setup guide

Linear Technology

Linear Technology DC1923A User manual

Linear Technology

Linear Technology DC1160 Quick setup guide

Linear Technology

Linear Technology DC1839A Quick setup guide

Linear Technology

Linear Technology DC1668A-B Quick setup guide

Linear Technology

Linear Technology LT3015 User manual

Linear Technology

Linear Technology 2429A Quick setup guide

Linear Technology

Linear Technology LTC4267 User manual

Linear Technology

Linear Technology DC2181A-A Quick setup guide

Linear Technology

Linear Technology DC1737A Quick setup guide

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual