Linear Technology DC1565A Quick setup guide

dc1565afa

DEMO MANUAL DC1565A

Description

LTC2153-14, LTC2153-12,

LTC2152-14, LTC2152-12,

LTC2151-14, LTC2151-12,

LTC2150-14, LTC2150-12

12-Bit/14-Bit, 170Msps to 310Msps ADCs

Demonstration circuit 1565A supports a family of

12‑Bit/14‑Bit 170Msps to 310Msps ADCs. Each assem‑

bly features one of the following devices: LTC2153‑14/

LTC2153‑12, LTC2152‑14/LTC2152‑12, LTC2151‑14/

LTC2151‑12, LTC2150‑14/LTC2150‑12, high speed ADCs.

The versions of the 1565A demo board are listed in Table1.

Depending on the required resolution and sample rate,

the DC1565A is supplied with the appropriate ADC. The

L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks

and PScope is a trademark of Linear Technology Corporation. All other trademarks are the

property of their respective owners.

circuitry on the analog inputs is optimized for analog input

frequencies from 5MHz to 140MHz. Refer to the data sheet

for proper input networks for different input frequencies.

Design files for this circuit board are available at

http://www.linear.com/demo

Table 1. DC1565A Variants

DC1565A VARIANTS ADC PART NUMBER RESOLUTION MAXIMUM SAMPLE RATE INPUT FREQUENCY

1565A‑A LTC2152‑14 14‑Bit 250Msps 5MHz to 140MHz

1565A‑B LTC2151‑14 14‑Bit 210Msps 5MHz to 140MHz

1565A‑C LTC2150‑14 14‑Bit 170Msps 5MHz to 140MHz

1565A‑D LTC2152‑12 12‑Bit 250Msps 5MHz to 140MHz

1565A‑E LTC2151‑12 12‑Bit 210Msps 5MHz to 140MHz

1565A‑F LTC2150‑12 12‑Bit 170Msps 5MHz to 140MHz

1565A‑G LTC2153‑14 14‑Bit 310Msps 5MHz to 140MHz

1565A‑H LTC2153‑12 12‑Bit 310Msps 5MHz to 140MHz

perForMAnce sUMMArY

(TA= 25°C)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Supply Voltage – DC1565A Depending on Sampling Rate and the A/D Converter

Provided, This Supply Must Provide Up to 500mA.

3 3.6 6 V

Analog Input Range Depending on SENSE Pin Voltage 1.5 or 1.32 VP‑P

Logic Input Voltages Minimum Logic High

Maximum Logic Low

1.3

0.6

Logic Output Voltages (Differential) Nominal Logic Levels (100Ω Load, 3.5mA Mode)

Common Mode

Minimum Logic Levels (100Ω Load, 3.5mA Mode)

Common Mode

350

1.25

247

1.25

Sampling Frequency (Convert Clock Frequency) See Table 1

Encode Clock Level Differential Encode Mode (ENC–Not Tied to GND) 0.2 1.9 V

Resolution See Table 1

dc1565afa

DEMO MANUAL DC1565A

TO PROVIDED

USB CABLE

TO PROVIDED

POWER SUPPLY

CHANNEL 1

PARALLEL/SERIAL

SINGLE-ENDED ENCODE CLOCK

(USE A LOW JITTER SIGNAL GENERATOR

WITH PROPER FILTERING)

dc1565a F01

3.6V TO 6V

qUick stArt proceDUre

Figure 1. DC1565 Setup

Demonstration circuit 1565A is easy to set up to evaluate

the performance of the LTC2152A/D converter family. Refer

to Figure 1 for proper measurement equipment setup and

follow the procedure below:

Setup

If a DC1371 Data Acquisition and Collection System was

supplied with the DC1565A demonstration circuit, fol‑

low the DC1371 Quick Start Guide to install the required

software and for connecting the DC1371 to the DC1565A

and to a PC.

DC1565A Demonstration Circuit Board Jumpers

The DC1565A demonstration circuit board should have

the following jumper settings as default positions: (as

per Figure 1)

JP2 PAR/SER: Selects parallel or serial programming

mode. (default ‑ serial)

perForMAnce sUMMArY

(TA= 25°C)

Input Frequency Range See Table 1

SFDR See Applicable Data Sheet

SNR See Applicable Data Sheet

dc1565afa

DEMO MANUAL DC1565A

qUick stArt proceDUre

Applying Power and Signals to the DC1565A

Demonstration Circuit

The DC1371 is used to acquire data from the DC1565A,

the DC1371 must first be connected to a powered USB

port and have 5V applied power before applying 3.6V to

6V across the pins marked V+and GND on the DC1565A.

DC1565A requires 3.6V for proper operation.

Regulators on the board produce the voltages required for

the ADC. The DC1565A demonstration circuit requires up

to 500mA depending on the sampling rate and the A/D

converter supplied.

The DC1565A should not be removed, or connected to

the DC1371 while power is applied.

Analog Input Network

For optimal distortion and noise performance the RC

network on the analog inputs may need to be optimized

for different analog input frequencies. For input frequen‑

cies above 140MHz, refer to the LTC2152 data sheet for a

proper input network. Other input networks may be more

appropriate for input frequencies less that 5MHz.

In almost all cases, filters will be required on both analog

input and encode clock to provide data sheet SNR.

The filters should be located close to the inputs to avoid

reflections from impedance discontinuities at the driven

end of a long transmission line. Most filters do not present

50Ω outside the passband. In some cases, 3dB to 10dB

pads may be required to obtain low distortion.

If your generator cannot deliver full‑scale signals without

distortion, you maybenefit from a medium power amplifier

based on a Gallium Arsenide Gain block prior to the final

filter. This is particularly true at higher frequencies where

IC based operational amplifiers may be unable to deliver

the combination of low noise figure and High IP3 point

required. A high order filter can be used prior to this final

amplifier, and a relatively lower Q filter used between the

amplifier and the demo circuit.

Apply the analog input signal of interest to the SMA

connector on the DC1565A demonstration circuit board

marked J4 AINA. This input is capacitively coupled to a

balun transformer ETC1‑1‑13 (lead free part number:

MABA007159‑000000).

Encode Clock

NOTE: Apply an encode clock to the SMA connector on

the DC1565A demonstration circuit board marked CLK+.

As a default the DC1565A is populated to have a single‑

ended input.

For the best noise performance, the encode input must

be driven with a very low jitter, sine wave source. The

amplitude should be large, up to 3VP‑P or 13dBm.

Using bandpass filters on theclock and the analoginput will

improve the noise performance by reducing the wideband

noise power of the signals. Data sheet FFT plots are taken

with 10‑pole LC filters made by TTE (Los Angeles, CA) to

suppress signal generator harmonics, non‑harmonically

related spurs and broadband noise. Low phase noise

Agilent 8644B generators are used for both the clock input

and the analog input.

Digital Outputs

The data outputs, data clock, and frame clock signals are

available on J1 of the DC1565A. This connector follows the

VITA‑57/FMC standard, but all signals should be verified

when using an FMC carrier card other than the DC1371.

Software

The DC1371 is controlled by the PScope™ System Soft‑

ware provided or downloaded from the Linear Technology

website at http://www.linear.com/software/.

To start the data collection software if PScope.exe, is in‑

stalled (by default) in \Program Files\LTC\PScope\, double

click the PScope icon or bring up the run window under

the start menu and browse to the PScope directory and

select PScope.

If the DC1565Ademonstration circuit is properly connected

to the DC1371, PScope should automatically detect the

DC1565A, and configure itself accordingly.

If everything is hooked up properly, powered and a suit‑

able convert clock is present, clicking the Collect button

should result in time and frequency plots displayed in

the PScope window. Additional information and help for

PScope is available in the DC1371 Quick Start Guide and in

the online help available within the PScope program itself.

dc1565afa

DEMO MANUAL DC1565A

qUick stArt proceDUre

Figure 3. Demobd Configuration Options

Figure 2. PScope Toolbar

Serial Programming

PScope has the ability to program the DC1565A board

serially through the DC1371. There are several options

available in the LTC2152 family that are only available

through serially programming. PScope allows all of these

features to be tested.

These options are available by first clicking on the Set

Demo Bd Options icon on the PScope toolbar (Figure 2).

This will bring up the menu shown in Figure 3.

This menu allows any of the options available for the

LTC2152 family to be programmed serially. The LTC2152

family has the following options:

Sleep Mode: Selects between normal operation, sleep

mode.

• Off(Default):EntireADCispowered,andactive

• On:TheentireADCispowereddown

NAP: Selects between normal operation and nap mode.

• Off(Default):Channeloneisactive

• On:Channeloneisinnapmode

Clock Inversion: Selects the polarity of the CLKOUT signal:

• Normal(Default):NormalCLKOUTpolarity

• Inverted:CLKOUTpolarityisinverted

ClkOut Phase: Selects the phase delay of the CLKOUT

signal:

• None(Default):NoCLKOUTdelay

• 45deg:CLKOUTdelayedby45degrees

• 90deg:CLKOUTdelayedby90degrees

• 135deg:CLKOUTdelayedby135degrees

Clock Duty Cycle: Enable or disables duty cycle stabilizer

• Stabilizeroff(Default):Dutycyclestabilizerdisabled

• Stabilizeron:Dutycyclestabilizerenabled

dc1565afa

DEMO MANUAL DC1565A

qUick stArt proceDUre

Output Current: Selects the LVDS output drive current

• 1.75mA(Default):LVDSoutputdrivercurrent

• 2.1mA:LVDSoutputdrivercurrent

• 2.5mA:LVDSoutputdrivercurrent

• 3.0mA:LVDSoutputdrivercurrent

• 3.5mA:LVDSoutputdrivercurrent

• 4.0mA:LVDSoutputdrivercurrent

• 4.5mA:LVDSoutputdrivercurrent

Internal Termination: Enables LVDS internal termination

• Off(Default):Disablesinternaltermination

• On:Enablesinternaltermination

Outputs: Enables digital outputs

• Enabled(Default):Enablesdigitaloutputs

• Disabled:Disablesdigitaloutputs

Test Pattern: Selects digital output test patterns

• Allout=0(default):Alldigitaloutputsare0

• Allout=1:Alldigitaloutputsare1

• Checkerboard:OF,andD13-D0Alternatebetween101

0101 1010 0101 and 010 1010 0101 1010 on alternat‑

ing samples.

• Alternating:Digitaloutputsalternatebetweenall1’sand

all0’sonalternatingsamples

Alternate Bit: Alternate bit polarity mode

• Off(Default):Disablesalternatebitpolarity

• On:Enablesalternatebitpolarity(BeforeenablingABP,

be sure the part is in offset binary mode)

TP Enable: Selects digital outputtest patterns. The desired

test pattern can be entered into the text boxes provided.

• Off(default):ADCinputdataisdisplayed

• On:Testpatternisdisplayed.

Randomizer: Enables data output randomizer

• Off(Default):Disablesdataoutputrandomizer

• On:Enablesdataoutputrandomizer

Two’s Complement:Enablestwo’scomplementmode

• Off(Default):Selectsoffsetbinarymode

• On:Selectstwo’scomplementmode

Once the desired settings are selected hit OK and PScope

will automatically update the register of the device on the

DC1565A demo board.

dc1565afa

DEMO MANUAL DC1565A

pArts list

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 4 C1, C3, C8, C10 Capacitor, X7R, 1µF, 10V, 10%, 0603 AVX, 0603ZC105KAT2A

2 2 C2, C9 Capacitor, X5R, 0.1µF, 10V, 10%, 0603 AVX, 0603ZD104KAQ2A

3 2 C4, C11 Capacitor, X7R, 47µF, 10V, 10%, 1210 Murata, GRM32ER71A476KE15L

4 8 C5, C6, C12, C16, C21, C23, Capacitor, X5R, 0.1µF, 10V, 10%, 0402 AVX, 0402ZD104KAQ2A

C34, C35

5 1 C7 Capacitor, X5R, 4.7µF, 6.3V, 20%, 0603 AVX, 06036D475MAT2A

6 1 C13 Capacitor, X5R, 2.2µF, 10V, 20%, 0603 AVX, 0603ZD225MAT2A

7 2 C14, C19 Capacitor, X7R, 0.01µF, 50V, 10%, 0603 AVX, 06035C103KAQ2A

8 3 C15, C26, C27 Capacitor, C0G, 4.7pF, 50V, 5%, 0402 AVX, 04025A4R7JAT2A

9 2 C17, C18 Capacitor, C0G, 8.2pF, 50V, 5%, 0402 AVX, 04025A8R2JAT2A

10 5 C20, C24, C28, C29, C36 Capacitor, X7R, 0.01µF, 16V, 10%, 0402 Murata, GRM155R71C103KA01D

11 1 C22 Capacitor, X5R, 2.2µF, 10V, 20%, 0603 AVX, 0603ZD225MAT2A

12 0 R15, C25 OPT 0402

13 4 C30, C31, C32, C33 Capacitor, C0G, 47pF, 16V, 10%, 0402 AVX, 0402YA470KA

14 1 D1 Diode Schottky, RF SER, 15V, SOT‑23 Avago, HSMS‑2822‑TR1G

15 1 JP1 Header, 2‑Pin 0.079 Single Row Samtec, TMM‑102‑02‑L‑S

16 1 J1 BGA Connector, 40 ×10 Samtec, SEAM‑40‑02.0‑S‑10‑2‑A‑K‑TR

17 2 J2, J3 Connector, SMA, 50Ω, Straight Mount Connex., 132134

18 1 J4 Connector, SMA, 50Ω, EDGE‑LANCH E. F. Johnson, 142‑0701‑851

19 1 L1 Inductor, 56nH, 0603 Murata, LQP18MN56NG02D

20 0 L2 OPT 0603

21 3 L3, L4, L5 Ferrite Bead, 1206 Murata, BLM31PG330SN1L

22 0 L6 Bead, OPT 1206

23 22 R1, R2, R3, R4, R5, R6, R7, R8, R10,

R16, R20, R21, R23, R24, R25, R27,

R28, R33, R34, R35, R36, R47

Resistor, Chip, 100, 1/16W, 5%, 0402 NIC, NRC04J101TRF

24 5 R9, R37, R38, R39, R40 Resistor, Chip, 1k, 1/16W, 5%, 0402 Yageo, RC0402FR‑071KL

25 2 R11, R18 Resistor, Chip, 33.2Ω, 1/16W, 1%, 0402 NIC, NRC04F33R2TRF

26 1 R12 Resistor, Chip, 86.6Ω, 1/16W, 1%, 0402 NIC, NRC04F86R6TRF

27 2 R13, R17 Resistor, Chip, 86.6Ω, 1/16W, 1%, 0603 Vishay, CRCW060386R6FNEA

28 2 R14, R19 Resistor, Chip, 10Ω, 1/16W, 5%, 0402 Vishay, CRCW040210R0JNED

dc1565afa

DEMO MANUAL DC1565A

pArts list

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

29 2 R26, R32 Resistor, Chip, 5.1Ω, 1/16W, 1%, 0402 Vishay, CRCW04025R10FKED

30 1 R29 PES., Chip, 0Ω, 0402 Vishay, CRCW04020000Z0ED

31 2 R30, R31 Resistor, Chip, 49.9Ω, 1/16W, 1%, 0402 Yageo, RC0402FR‑0749R9L

32 3 R41, R42, R43 Resistor, Chip, 5.1k, 1/16W, 1%, 0402 NIC, NRC04F5101TRF

33 3 TP1, TP2, TP3 Testpoint, Turret, 0.094" pbf Mill‑Max, 2501‑2‑00‑80‑00‑00‑07‑0

34 2 T1, T3 Transformer, MABA‑007159‑000000 M/A‑COM, MABA‑007159‑000000

35 1 T2 Transformer, WBC1‑1L Coilcraft, WBC1‑1L

36 1 U1 IC, LTC2152CUJ, 40‑Pin QFN 6mm ×6mm Linear Technology, LTC2152CUJ#PBF

37 1 U3 IC, LT1763CS8‑1.8, SO8 Linear Technology, LT1763CS8‑1.8#TRPBF

38 1 U4 IC, LT1763CS8‑3‑3, SO8 Linear Technology, LT1763CS8‑3.3#TRPBF

39 1 U5 IC, EEPROM, 32k, 400khz, 8TSSOP MICROChip, 24LC32A‑I/ST

40 1 Fab, Printed Circuit Board Demo Circuit 1565A

41 2 Top & Botton Stencil for Proto Stencil 1565A

dc1565afa

DEMO MANUAL DC1565A

scheMAtic DiAgrAM

D D

C C

B B

A A

AINA

SENSE







CLK+

V+

3V - 6V

GND

CLK-

PAR_SER

aina-

aina+

sense

of+

of-

gnd

sense

VDD

OVDD

VDD

VDD OVDD

VDD

DA4_5+

DA10_11+

DA8_9+

DA2_3+

DA12_13+

DA6_7+

CLKOUT+

SCK

SDI

SDO

DA0_1-

DA10_11-

DA12_13-

DA0_1+

DA6_7-

CLKOUT-

DA4_5-

DA2_3-

DA8_9-





 

 









TECHNOLOGY





























































 

 









TECHNOLOGY





























































 

 









TECHNOLOGY



























































  



 





  



 





  



 



R18

R34

OPT

R34

OPT

BEAD

C13

2.2uF

0603

C13

2.2uF

0603

R28

100

R28

100

R14

C16

0.1uF

C16

0.1uF

R10

C34

0.1uF

C34

0.1uF

J2J2

R17

86.6

0603

R17

86.6

0603

OPT

JP2JP2 1

0.1uF

R26

5.1

R26

5.1

R45

R24

OPT

R24

OPT

C24

0.01uF

C24

0.01uF

R19

C12

0.1uF

C12

0.1uF

R32

5.1

R32

5.1

R25

OPT

R25

OPT

C29

0.01uF

C29

0.01uF

0.1uF

J4J4

R22

56nH

0603

56nH

0603

C21

0.1uF

C21

0.1uF

R23

OPT

R23

OPT

C10

1uF

C10

1uF

MABA-007159-000000

4 3

R27

OPT

R27

OPT

R35

OPT

R35

OPT

LT1763CS8-1.8















C20

0.01uF

C20

0.01uF

R36

OPT

R36

OPT

C17

8.2pF

C17

8.2pF

MABA-007159-000000

4 3

C35

0.1uF

C35

0.1uF

TP1TP1

R11

R13

86.6

0603

R13

86.6

0603

4.7uF

TP3TP3

C18

8.2pF

C18

8.2pF

WBC1-1L

TP2TP2

R15

OPT

R15

OPT

+ C11

47uF

1210

+ C11

47uF

1210

R16

100

R16

100

R31

49.9

R31

49.9

R20

R47

100

R47

100

0.1uF

R21

C22

2.2uF

C22

2.2uF

C15

4.7pF

C15

4.7pF

C36

0.01uF

C36

0.01uF

R44

LTC2152UJ

















































































R12 86.6

R33

OPT

R33

OPT

1uF

R30

49.9

R30

49.9

R29 0R29 0

C19

0.01uF

0603

C19

0.01uF

0603

C14

0.01uF

0603

C14

0.01uF

0603

J3J3

C23

OPT

C23

OPT

BEAD

C28

0.01uF

C28

0.01uF

dc1565afa

DEMO MANUAL DC1565A

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa‑

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

scheMAtic DiAgrAM

D D

C C

B B

A A

CHANNEL 0

CHANNEL 1

+3.3V

VDD

DA10_11+

DA10_11-

DA6_7-

DA6_7+

DA2_3-

DA2_3+

DA12_13-

DA12_13+

DA4_5+

DA4_5-

DA0_1+

DA0_1-

DA8_9-

DA8_9+

CLKOUT+

CLKOUT-

SDO

SCK

SDI





 

 









TECHNOLOGY





























































 

 









TECHNOLOGY





























































 

 









TECHNOLOGY

























































C31

47pF

C31

47pF

J1J

SEAM-10X40PIN

J1J

SEAM-10X40PIN



















J10



J11



J12



J13



J14



J15



J16



J17



J18



J19



J20



J21



J22



J23



J24



J25



J26



J27



J28



J29



J30



J31



J32



J33



J34



J35



J36



J37



J38



J39



J40

R41

J1E

SEAM-10X40PIN

J1E

SEAM-10X40PIN



















E10



E11



E12



E13



E14



E15



E16



E17



E18



E19



E20



E21



E22



E23



E24



E25



E26



E27



E28



E29



E30



E31



E32



E33



E34



E35



E36



E37



E38



E39



E40

J1A

SEAM-10X40PIN

J1A

SEAM-10X40PIN

















A10



A11



A12



A13



A14



A15



A16



A17



A18



A19



A20



A21



A22



A23



A24



A25



A26



A27



A28



A29



A30



A31



A32



A33



A34



A35



A36



A37



A38



A39



A40

C32

47pF

C32

47pF

C33

47pF

C33

47pF

J1K

SEAM-10X40PIN

J1K

SEAM-10X40PIN



















K10



K11



K12



K13



K14



K15



K16



K17



K18



K19



K20



K21



K22



K23



K24



K25



K26



K27



K28



K29



K30



K31



K32



K33



K34



K35



K36



K37



K38



K39



K40

R46

100K

R46

100K

J1F

SEAM-10X40PIN

J1F

SEAM-10X40PIN



















F10



F11



F12



F13



F14



F15



F16



F17



F18



F19



F20



F21



F22



F23



F24



F25



F26



F27



F28



F29



F30



F31



F32



F33



F34



F35



F36



F37



F38



F39



F40

J1B

SEAM-10X40PIN

J1B

SEAM-10X40PIN

















B10



B11



B12



B13



B14



B15



B16



B17



B18



B19



B20



B21



B22



B23



B24



B25



B26



B27



B28



B29



B30



B31



B32



B33



B34



B35



B36



B37



B38



B39



B40

C30

47pF

C30

47pF

J1G

SEAM-10X40PIN

J1G

SEAM-10X40PIN



















G10



G11



G12



G13



G14



G15



G16



G17



G18



G19



G20



G21



G22



G23



G24



G25



G26



G27



G28



G29



G30



G31



G32



G33



G34



G35



G36



G37



G38



G39



G40

R38

R42

J1C

SEAM-10X40PIN

J1C

SEAM-10X40PIN

















C10



C11



C12



C13



C14



C15



C16



C17



C18



C19



C20



C21



C22



C23



C24



C25



C26



C27



C28



C29



C30



C31



C32



C33



C34



C35



C36



C37



C38



C39



C40

R37

R39

R40

JP1JP1

J1H

SEAM-10X40PIN

J1H

SEAM-10X40PIN





















H10



H11



H12



H13



H14



H15



H16



H17



H18



H19



H20



H21



H22



H23



H24



H25



H26



H27



H28



H29



H30



H31



H32



H33



H34



H35



H36



H37



H38



H39



H40

R43

J1D

SEAM-10X40PIN

J1D

SEAM-10X40PIN

















D10



D11



D12



D13



D14



D15



D16



D17



D18



D19



D20



D21



D22



D23



D24



D25



D26



D27



D28



D29



D30



D31



D32



D33



D34



D35



D36



D37



D38



D39



D40

24LC32A-I /ST

















dc1565afa

DEMO MANUAL DC1565A

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035‑7417

(408) 432‑1900 ●FAX: (408) 434‑0507 ●www.linear.com

 LINEAR TECHNOLOGY CORPORATION 2011

LT 1211 REV A • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design‑, marketing‑, and/or manufacturing‑related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims

arisingfromthehandlingoruseofthegoods.Duetotheopenconstructionoftheproduct,itistheuser’sresponsibilitytotakeanyandall

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica‑

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035

Table of contents

Other Linear Technology Motherboard manuals

Linear Technology

Linear Technology DC1261A Quick setup guide

Linear Technology

Linear Technology DC1257B Quick setup guide

Linear Technology

Linear Technology DC1369A Quick setup guide

Linear Technology

Linear Technology DC1697A Quick setup guide

Linear Technology

Linear Technology DC2581A Quick setup guide

Linear Technology

Linear Technology DC1684A-B Quick setup guide

Linear Technology

Linear Technology DC1529A User manual

Linear Technology

Linear Technology DC1705A Quick setup guide

Linear Technology

Linear Technology DC1639A User manual

Linear Technology

Linear Technology DC1763A Quick setup guide

Linear Technology

Linear Technology LT1765EFE User manual

Linear Technology

Linear Technology DC1889A Quick setup guide

Linear Technology

Linear Technology DC1562B Quick setup guide

Linear Technology

Linear Technology DC1123 User manual

Linear Technology

Linear Technology DC1123 User manual

Linear Technology

Linear Technology DC2025A Quick setup guide

Linear Technology

Linear Technology DC2016A Quick setup guide

Linear Technology

Linear Technology DC1544 User manual

Linear Technology

Linear Technology LTC3880 Quick setup guide

Linear Technology

Linear Technology 2429A Quick setup guide

Linear Technology

Linear Technology DC2367A Quick setup guide

Linear Technology

Linear Technology 1172A User manual

Linear Technology

Linear Technology DC2117A Quick setup guide

Linear Technology

Linear Technology DC1698A Quick setup guide

Popular Motherboard manuals by other brands

DFI

DFI SD170 user manual

ASROCK

ASROCK ROMED8-2T user manual

Asus

Asus P2L97A user manual

Winmate

Winmate IC70 user manual

Asus

Asus MES-B user manual

Grantech

Grantech SYS8F377VGGA-3OMN user manual

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR user guide

Gigabyte

Gigabyte GA-9IVDT user manual

Texas Instruments

Texas Instruments ADS8372EVM user guide

Commell

Commell MS-C73 user manual

IBT Technologies

IBT Technologies MB860 user manual

Nvidia

Nvidia TEGRA DG-04927-001_V01 user guide

Biostar

Biostar M7VIT Bravo Description

Intel

Intel D33217CK specification

Asus

Asus F1A55-M LX PLUS R2.0 user manual

EPC

EPC EPC9147C quick start guide

Asus

Asus EX-B760M-V5 D4 quick start guide

EPOX

EPOX MU-8KHA0010 user manual