Life Smart YAA02E-5 Quick start guide

--SAVE THESE INSTRUCTIONS-- 1

OIL FILLED RADIATOR

Safety & Operating Instructions

Model # YAA02E-5

YAA02E-7

YAA02E -9

YAA02E -11

YAA02E -13

YL-A02LCD

WARNING!

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR PERSONAL INJURY, READ

ALL THE INSTRUCTIONS BEFORE USING THIS

HEATER, AND FOLLOW THESE INSTRUCTIONS!

BE SURE TO SAVE THIS MANUAL FOR FUTURE

REFERENCE

--SAVE THESE INSTRUCTIONS-- 2

CONTENTS

1. Important Instructions ............................

2. Parts Identification ..................................

Mode and Technical data…………………

Safety Control…………………………….

3. Assemble ..................................................

4. Operate......................................................

Set temperature

…………………………………

Set timer(auto- off)…………………………

Set timer(auto- on)…………………………

Timer function examples…………………..

Fahrenheit/Celsius function…………………

5. Care and Cleaning ....................................

Conformity with Directives

Environmental Protection

--SAVE THESE INSTRUCTIONS-- 3

1. IMPORTANT INSTRUCTIONS

Basic safety precautions should always be followed when using electrical products,

especially when children are present.

WARNING: TO AVOID THE RISK OF ELECTRICAL SHOCK, FIRE OR INJURY

TO PERSON, ALWAYS MAKE SURE THE PRODUCT IS UNPLUGGED FROM

THE ELECTRICAL OUTLET BEFORE RELOCATING, SERVICING, OR

CLEANING IT.

1. Read all instructions before using this heater.

2. Connect the appliance to single-phase AC power supply of the voltage specified on

the rating label.

3. This product is intended for indoor, non-commercial, non-industrial, household use

only. Do not use outdoors. Do not use the product for any other purpose.

4. This heater is not intended for use in bathrooms, laundry areas, and similar indoor

locations. Do not use this heater in the immediate surroundings of a bath, a shower or

a swimming pool.

5. Never leave this product unattended while it is in use. Always turn the product to the

“OFF” position and unplug it from the electrical outlet when it is not in use.

6. Extreme caution is necessary when this heater is used by or near children or invalids

and whenever the heater is left operating and unattended. Keep the product out of the

reach of children and pets. This product is not intended to use by children. Children

should be supervised to ensure that they do not play with the heater.

7. Do not use the product while sleeping or place it near a person who is sleeping.

8. Place the product on a flat, steady, stable, heat-resistant surface.

9. Do not place the product on or near surfaces that may be damaged by heat (i.e.,

delicate rugs, wall paper, floor coverings not made of heat-resistant material, etc.).

10. Do not place this product near flammable materials, surfaces or substances (i.e.,

curtains, draperies, walls, gasoline, paint, flammable liquids, etc.), as there may be a

risk of fire.

11. Do not insert or place flammable materials (i.e., paper, plastic, or cardboard) in, on

or near the product.

12. Use the product in a well-ventilated area. .

13. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If

provided, use handles when moving this heater. Keep combustible materials, such as

furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front

of the heater and keep them away from the sides and rear.

14. Do not touch hot surfaces. Always use the handle of the product. Use protective

oven mitts or gloves to avoid burns or serious personal injury.

15. A heater has hot and arcing or sparking parts inside.

16. Always maintain your distance from the product while it is use to avoid serious burns

and personal injury

17. Never insert fingers, hair, metallic objects or any other item into the vents and

openings of the product, as an electrocution, fire, and/or burn hazard exists.

18. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as

this may cause an electric shock, fire, or damage to the heater.

19. Never block the air openings of the product or place it on a soft surface (i.e., a bed or

a couch) where the air openings may be blocked. Wipe the air openings clean if they

become clogged.

--SAVE THESE INSTRUCTIONS-- 4

20. Do not use this product to dry or heat clothing, shoes, pipes, or any other item.

21. Do not place or expose this product to water or other liquids.

22. Do not move the product when it is heated. Allow the product to thoroughly cool

before handling it.

23. Do not run cord under carpeting and do not cover cord with throw rugs, runners or

the like. Arrange cord away from traffic area and where it will not be tripped over.

24. To disconnect the product, turn the controls to the “OFF” position, then remove the

plug from the electrical outlet. Disconnect the plug (do not pull on the Power Cord)

from the electrical outlet.

25. Do not use attachments not recommended or sold by the product manufacturer, as a

risk of fire, electrical shock, or serious personal injury may result.

26. Attachments, when furnished, may become hot during use. Allow any attachments

to cool before handling them.

27. To prevent a possible fire, do not block air intakes or exhaust openings in any

manner. Do not use on soft surfaces, like a bed, where openings may become

blocked.

28. To avoid a circuit overload when using this product, do not operate another high-

wattage product on the same electrical circuit.

29. Avoid the use of an extension cord because the extension cord may overheat and

cause a risk of fire.

30. Do not allow the Power Cord to hang (i.e., over the edge of a table or counter) or

place/run the Power Cord under rugs or in high-traffic areas where it may be tripped

over or pulled.

31. Do not put any stress on the Power Cord where it connects to the product, as the

Power Cord could fray and break.

32. Do not plug or unplug the product from the electrical outlet with a wet hand.

33. Keep the Power Cord and product away from heated surfaces.

34. When scrapping the heater, follow the regulations concerning the disposal of oil.

35. The heater should not be used in a room, of which the floor area is less than 5 M2.

36. Use this heater only as described in this manual. Any other use not recommended by

the manufacturer may cause fire, electric shock, or injury to persons.

37. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety.

38. Children should be supervised to ensure that they do not play with the appliance.

39. If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

40. WARNING: In order to avoid overheating, do not cover the heater.

41. heater must not be located immediately below a socket outlet.

42. Do not use this heater in the immediate surroundings of a bath, a shower or a

swimming pool.

43. this heater is filled with a precise quantity of special oil. Repairs requiring opening of

the oil container are only to be made by the manufacturer or his service agent who

should be contacted if there is an oil leak;

44. when scrapping the heater, follow the regulations concerning the disposal of oil.

--SAVE THESE INSTRUCTIONS-- 5

2. Parts Identification

1. Castor Wheels 2. Button 3. LCD Display Screen 4. Power Switch

5. Control Panel 6. Front Cover 7. Radiator Fins 8. Cord Storage

Mode and Technical data

Safety Control (Thermal Cut-Out)

This model has two levels of over heat protection

1. Automatic thermal cut-off

Switches off the heater in the event of overheating or malfunction and resets once the

temperature drops to a normal level.

2. Thermal fuse

In the event that the automatic thermal cut-off fails to operate the heater has a further

safety device. This is a non-resettable switch which will require the unit be returned to

an Approved Service Agent for replacement.

If overheating or malfunctions continue, return the heater to an Approved Service

Agent for examination.

SPECIFICATIONS

Model No.

Rated Voltage & Frequency

Wattage

YAA02E -5

220-240V~, 50 Hz

1000W(I+II);600W(II);400W( I )

YAA02E -7

220-240V~, 50 Hz

1500W(I+II);900W(II);600W( I )

YAA02E -9

220-240V~, 50 Hz

2000W(I+II);1200W(II);800W( I )

YAA02E -11

220-240V~, 50 Hz

2500W(I+II);1500W(II);1000W( I )

YAA02E -13

220-240V~, 50 Hz

2500W(I+II);1500W(II);1000W( I )

Castor Wheel Assembly

Description

Drawing

Quantity

Castor

Wheels

Wing Nut

Arc-shaped

Bracket

--SAVE THESE INSTRUCTIONS-- 6

3. Assemble

1. Unpack the Castor Wheels and Arc-shaped Brackets from the product packaging.

2. Turn the radiator upside-down on a scratch-free and stable surface to prevent damage

to the paint finish or your floor surfacing.

3. Fit the two (2) Castor Wheels onto the radiator by placing the Arc-shaped Brackets

between the outermost fins on each side of the radiator.

4. Securely fasten the two (2) Castor Wheels onto the radiator by screwing two (2) Wing

Nuts onto each Foot.

5. Turn the radiator in upright position after the Castor Wheel Assembly fitted. For the

correct upright position, please refer to fig. below

4. Operate

This heater is equipped with ElectronicDigital Controls that provide the ability to set the

temperature to the exact degree desired .To operate , simply follow these instructions.

NOTE:The temperature display will not reflect the accurate room temperature until the heater has

been operating for at least 20 minutes.

1. Turn on Power Switch, Press the power button once to start the heater on High

Power( ), Continuous Run. If left at this setting , the unit will run continuously on

High Power and will not shut off until the unit is manually turned off or the room

temperature over 30℃.

2. Press the power button again to change to Lower Power ( ), Continuous Run. If left

at this setting, the unit will run continuously on Lower Power and will not shut off

until the unit is manually turned off or the room temperature over 30℃.

3. Press the power button a third time to turn the heater OFF.

Note:the heater will run continuously if not setting temperature.

CAUTION: Only operate the radiator in

normal upright position with Castor

Wheel Assemblies attached to the bottom

of the unit (wheels on the bottom, controls

on the top), any other position could create

a hazardous situation

--SAVE THESE INSTRUCTIONS-- 7

Note: if operated at the Low setting, the heater will not provide as much heat output as in

the High setting , however , the Low setting will not require a much electrical current to

operate .To avoid overloading a circuit , do not plug the heater into a circuit that already

has other appliances working.

SET TEMPERATURE

MODE F/C

1. Press the Mode button until the temperature icon blinks .

2. Use the + and -button to set the desired temperature,from 13 to30℃.

3. The temperature icon will stop blinking and the current room temperature will appear after the

desired temperature is set.

4. The heat will turn-off shortly after the desired temperature is reached and the temperature display

will blink.

5. The heater will turn back on when the room temperature drops below the desired temperature . the

temperature display will then stop blinking and will display the current room temperature.

SET TIMER (AUTO-OFF)

NOTE: This function should only be set if you desire that the heater be automatically

shut off after a certain period of time(1 to 10 hours from the time the function is set)

NOTE: Always set the desired temperature prior to setting the Timer(see step2) so that

the heater will shut off at the desired temperature setting.

6. Press the Mode button until the timer icon blinks. The hour display will appear . The Auto Off icon

will also appear.

7. Use the +and -buttons to set the heater operation time between 1 and 10 hours. This function will

activate once the timer icon stops blinking.

8. The heater will automatically turn-off when time runs out.

NOTE :If the desired temperature was set prior to setting the timer function , the heater will cycle on

and off as per the selected desired temperature setting and will discontinue operation once the

programmed timer setting has been reached(default is 10 hours).

SET TIMER (AUTO-ON)

NOTE: This function provides a delayed start option and should only be set if you

desire that the heater be automatically turned ON after a certain period of time (1 to

10 hours from the time the function is set).

NOTE: Always set the desired temperature prior to setting the timer (see step2)so that

the heater will turn on at the desired temperature setting.

1. Press the Mode button until the timer icon blinks. The hour display will appear .The Auto On icon will

also appear.

POWER

--SAVE THESE INSTRUCTIONS-- 8

2. Use the + and - buttons to set the heater start time between 1 and 10 hours. This function will activate

once the timer icon stops blinking.

3. The heater will automatically turn on when time expires.

NOTE: If the desired temperature was set prior to setting the timer function, the heater

will cycle on and off as per the selected desired temperature setting once the heater

begins to operate.

NOTE: When using the Auto-On function the heater will turn on after the set time has

elapsed. If the Auto-Off function has not been set , a default timer of 10 hours will be

applied to the function.

TIMER FUNCTION EXAMPLES

Auto on Example:

Set Auto off for 3 hours

the heater will start running after 2 hours has elapsed；.

Set Auto on for 2 hours

The heater will then operate for 3 additional hour and then immediately turn off.

Auto off Example:

Set Auto off for 7 hours ：

The heater will shut off after 7hours has elapsed.

FAHRENHEIT/CELSIUS FUNCTION

NOTE: This heater offers the option to read the temperature setting in either

Fahrenheit or Celsius.

1. F/C feature functions from only the power or set temperature screens.

2. Press F/C button to toggle between Fahrenheit and Celsius.

5. Care and Cleaning

CAUTION: Allow the product to completely cool before handling or cleaning it.

Ensure the product is in the “O” OFF position and the Power Cord is unplugged from the

electrical outlet before cleaning the product.

•Always ensure the product’s housing is intact and completely assembled before each

use.

•Do not touch hot surfaces. Always use the handle of the product. Use protective

mitts or gloves to avoid serious burns or other personal injury.

•Clean the exterior surface of the product by wiping it with a soft, damp cloth.

CAUTION: Do not allow water or other liquids to run into the interior of the product, as

this could create a fire and/or electrical hazard.

•Do not use any abrasive cleaners or solvents, as product damage will occur.

•Store the product in a clean, dry place when it is not in use.

--SAVE THESE INSTRUCTIONS-- 9

Conformity with Directives

This product is CE marked to denote conformity with Directives 73/23/EEC(Low

Voltage) and 89/336/EEC (Electromagnetic Compatibility), as amended.

Environmental Protection

Disposal

This marking indicates that this product should not be disposed with

other household wastes throughout the EU. To prevent possible harm

to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material

resources. To return your u

sed device, please use the return and

collection systems or contact the retailer where the product was

purchased.

They can take this product for environmental safe

recycling.

--SAVE THESE INSTRUCTIONS-- 10

This manual suits for next models

Table of contents

Other Life Smart Heater manuals

Life Smart

Life Smart LS-IF1500-MOFP Quick start guide

Life Smart

Life Smart LS-PP1500-6NAT User manual

Life Smart

Life Smart HT1041 User manual

Life Smart

Life Smart HT1269UV User manual

Life Smart

Life Smart LS-6BPIQH-X Quick start guide

Life Smart

Life Smart HT1289 User manual

Life Smart

Life Smart XXHT1086US User manual

Life Smart

Life Smart LS-PP1800-6WCH User manual

Life Smart

Life Smart HT1193 User manual

Life Smart

Life Smart LS-3ECO User manual

Life Smart

Life Smart LS-8WIQH-LB User manual

Life Smart

Life Smart LS-3W-BPIQT User manual

Life Smart

Life Smart LS-1000X-6W User manual

Life Smart

Life Smart XXAC3004US User manual

Life Smart

Life Smart LS1001HH13 Quick start guide

Life Smart

Life Smart HT1269 User manual

Life Smart

Life Smart ZCHT1040US User manual

Life Smart

Life Smart LS-1000X-4C User manual

Life Smart

Life Smart HT1216 User manual

Life Smart

Life Smart LS-8WQH-DLX13B User manual

Life Smart

Life Smart S-1500-6WB operati Quick start guide

Life Smart

Life Smart LS-1000X-4M User manual

Life Smart

Life Smart LS-4W1500-X Quick start guide

Life Smart

Life Smart ZCHT1074US User manual

Popular Heater manuals by other brands

oventrop

oventrop Regucor Series quick start guide

Blaze King

Blaze King CLARITY CL2118.IPI.1 Operation & installation manual

ELMEKO

ELMEKO ML 150 Installation and operating manual

BN Thermic

BN Thermic 830T instructions

KING

KING K Series Installation, operation & maintenance instructions

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Installation instructions and owner's manual

Well Straler

Well Straler RC-16B user guide

EUROM

EUROM 333299 instruction manual

Heylo

Heylo K 170 operating instructions

Eterna

Eterna TR70W installation instructions

Clarke

Clarke GRH15 Operation & maintenance instructions

IRSAP

IRSAP The Radiator Company Ovali Fitting instructions

Empire Heating Systems

Empire Heating Systems WCC65 Installation and owner's instructions

Wetekom

Wetekom 92 86 43 Original instructions

Desa

Desa SPC170-F owner's manual

Watlow

Watlow Watrod Electric Tubular Heaters Specifications

Haverland

Haverland ECO-DRY GPS Series Instruction & installation manual

Stelpro

Stelpro ASILVC2060 Series user guide